TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2018 Behr Process Corporation Santa Ana, CA 92705 U.S.A.
Revised 12/2018
1 of 1
ADVANCED DECKOVER® SMOOTH COATING
NO. 5000
PRODUCT INFORMATION
BEHR PREMIUM ADVANCED DECKOVER® Smooth is an innovative solid color coating that resurfaces properly prepared weathered
wood and concrete. The advanced 100% acrylic resin creates a durable coating on your tired deck, rejuvenating its look.
ADVANCED DECKOVER Smooth is designed to conceal splinters & cracks up to 1/4" and creates a smooth, slip-resistant nish.
Our latest formula now features even better adhesion and cracking resistance. It can be tinted to 54 solid custom colors.
RECOMMENDED USES:
Recommended for properly prepared interior and exterior weathered or cracked horizontal and vertical surfaces such as:
• Wood • Composite • Concrete
Do not use on drivable surfaces such as garage oors and driveways.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 5000 Deep Base 116  oz / 14  oz
Resin Type: 100% Acrylic
Weight per Gallon: 11.45 lbs
% Solids by Volume: 51% +/- 2%
% Solids by Weight: 63% +/- 2%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 95-105 KU (Paste Paddle)
Recommended Film Thickness:
Wet: 10.6 mils Dry: 5.4 mils per coat
(Total Dry Film Thickness: 10.9 mils for 2 coats)
Coverage: 75 sq ft/gal for 2 coats (required)
APPLICATION:
Brush: Nylon/polyester brush
Roller: 1/4"- 1/2" nap
Airless Spray: At packaged consistency
Tip: .027"-.035" with no lter at 2400-3200 psi
Dry Time: @ 77°F & 50% RH
To Recoat: 4-6 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
• For nail holes and cracks up to 1/4", completely ll in with
ADVANCED DECKOVER Coating using a nylon/polyester
brush and allow to dry prior to rolling. Deep nail holes and
cracks require additional lling.
• Use pressure while rolling and apply generously.
• For optimum performance, lm uniformity, leveling,
adhesion and crack lling, a second coat MUST be applied.
Maintain a wet edge when applying.
• For best results, coat all accessible board ends.
SURFACE PREPARATION:
The following steps and products are required: All
surfaces must be clean, sound, dry and free of any dirt, oil,
and grease before application. Wood Surfaces: Replace
rotting or unstable boards and remove loose splinters.
If you remove mildew stains and dirt with a product such
as BEHR PREMIUM All-In-One Wood Cleaner No. 63, then
you must use a product such as BEHR PREMIUM Wood
Stain & Finish Stripper No. 64 to remove all loose wood
bers, peeling paint/stain or deteriorated coatings prior
to application of ADVANCED DECKOVER Coating. On new
wood, use a product such as BEHR PREMIUM All-In-One
Wood Cleaner No. 63 to remove mill glaze and open the
pores of the wood. Rinse thoroughly and allow to dry
before coating.
Concrete Surfaces: Avoid areas that are structurally weak
or subject to hydrostatic pressure up to 8 psi. Allow new
surfaces to cure for 30 days. Clean and etch surface using a
product such as a muriatic acid to achieve a textured prole
similar to 150 grit sandpaper. Follow all label instructions.
If the previous coating is failing or peeling, use a paint
stripper to remove old coating. See behr.com for
additional product information.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water. For proper
disposal of empty containers and unused product, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• While this textured product provides a slip resistant nish,
surfaces may still become slippery when wet.
• Use product when air and surface temperatures are
between 50-90° F.
• Do not use if rain is expected within 24 hours and avoid
painting if humidity is expected to be greater than 80%.
• Avoid applying paint in direct sunlight or hot surfaces.
• Do not use on drivable surfaces such as garage oors and
driveways.
• Do not use without the addition of tinting colorants.
• DO NOT THIN PRODUCT.
• Test product for color on a small hidden area before
proceeding.
• Protect from freezing.
• Shelf life under normal conditions is two years (unopened
containers).
GENERAL INFORMATION:
CAUTION IRRITANT HARMFUL IF SWALLOWED.
MAY CAUSE EYE, NOSE AND THROAT IRRITATION.
AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING
OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION
AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE
VENTILATION.To avoid breathing vapors and spray mist,
open windows and doors or use other means to ensure
fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator (NIOSH approved
for organic vapor with P series particulate pre-lter) may
oer additional protection. A dust mask does not provide
protection against vapors. Avoid contact with eyes and skin.
Wash thoroughly after handling. Close container after each
use. FIRST AID: If you experience diculty in breathing,
leave the area to obtain fresh air. If continued diculty is
experienced, get medical assistance immediately. In case of
eye contact, ush immediately with plenty of water for at
least 20 minutes and get medical attention; for skin, wash
thoroughly with soap and water. If swallowed, get medical
attention immediately.
COMPLIES WITH THE BELOW AS OF 12/1/2018
SCAQMD YES LADCO YES
CARB SCM 2007 YES AIM YES
CARB YES LEED v.3 (2009)
†
YES
OTC Phase II YES MPI# 127
OTC YES FLAME SPREAD/CLASS A YES
†
Please visit www.usgbc.org/LEED for additional details.