Use and Care Manual

TECHNICAL DATA ROC-109
CONCRETE & GARAGE
®
FLOOR PAINT + PRIMER
Form: GDH-1355
Rev.: 051517
1
DESCRIPTION AND USES .
Rust-Oleum
®
Concrete and Garage Floor Paint and Primer is a
ready-to-use interior/exterior concrete floor paint designed for use on
garages, carports, driveways, basements, porches, patios, walkways,
and pool decks A single coat of this self-priming concrete floor paint
saves time and resists damage from hot tires, motor oil, grease and
gasoline. The durable, UV and weather resistant satin finish is easy
to maintain and resists fading and peeling. It is environmentally
friendly and can be easily cleaned with soap and water.
Not recommended for use on asphalt or wood surfaces.
. FEATURES .

Advanced acrylic formula

Hot tire and chemical resistant

UV and weather resistant

Interior/exterior durability
.PRODUCTS .
SKU Description
225359 Armor Gray Satin – 1-Gallon
225380 Battleship Gray Satin – 1-Gallon
225381 Satin Tint Base - 1-Gallon
319550 Satin Deep Tint Base – 1-Gallon
320173 Armor Gray Satin – 5-Gallon
320172 Battleship Gray Satin– 5-Gallon
320174 Satin Tint Base – 5-Gallon
320175 Satin Deep Tint Base – 5-Gallon
. APPEARANCE .
Dries to a satin finish.
.PRODUCT APPLICATION .
READ ALL INSTRUCTIONS CAREFULLY BEFORE STARITNG
PROJECT
SURFACE PREPARATION
Bare Concrete Surfaces: Proper surface preparation is critical to
performance. Allow new concrete to cure for a minimum of 28 days.
Before coating bare concrete surfaces, remove grease, oil, salt and
other contaminants with Rust-Oleum Heavy-Duty Degreaser (sold
separately) or Rust-Oleum Cleaner & Degreaser (sold separately).
Scrub spots thoroughly with a stiff bristle brush or broom and wipe up
excess cleaner with rags or paper towels to keep contaminants from
spreading. Rinse thoroughly with fresh water. Repeat as necessary
to completely clean.
If necessary, use a wire brush or sander to remove any loose or
unsound concrete or masonry. For proper penetration and maximum
adhesion, use Rust-Oleum Clean & etch (sold separately). Follow
label instructions carefully and allow the floor to dry completely. Wipe
your fingers over the clean, dry surface. If you see and dust or
powder on your fingers, repeat scrubbing and rinsing until the floor is
clean.
Previously Painted, Stained or Sealed Concrete Surfaces:
Use a
wire brush to remove any loose or peeling paint, stain or sealer. To
ensure proper adhesion, scuff sand the entire surface and clean with
a solvent such as acetone. Rinse or sweep away dust and other
particles.
.PRODUCT APPLICATION (cont.) .
SURFACE PREPARATION (cont.)
Wash the entire floor with Rust-Oleum heavy-Duty Degreaser
(diluted as stated on the label) or Rust-Oleum Cleaner & Degreaser
and scrub the surface using a stiff bristle brush or broom. Spot etch
all exposed concrete surfaces using Rust-Oleum concrete Etch or
Rust-Oleum Clean & Etch. Rinse thoroughly and allow to dry
completely.
WARNING!
If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT
WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a
NIOSH-approved respirator to control lead exposure. Clean
up carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
APPLICATION
Rust-Oleum concrete and Garage Floor Paint and Primer is ready to
use. Do not thin. Apply only when air, material, and surface
temperatures are between 50-90°F (10-32°C) and the relative
humidity is below 85%. Do not paint outdoors if rain is expected
within 48 hours. If using more than one gallon, intermix (box) all cans
of the same product to ensure gloss uniformity. Stir thoroughly before
applying. NOTE: Painted floors may be slippery when wet. If desired,
Rust-Oleum Anti-Skid Additive (sold separately) may be added to the
mixed coating.
Use a brush or edger to trim the perimeter and hard-to-reach areas.
Use a long handled extension pole and a high quality ⅜” nap roller
cover to apply an even coat of Rust-Oleum Concrete Garage and
Floor Paint and Primer onto the surface. Apply in 4’x4’ foot sections
and maintain a wet edge to prevent lap marks and gloss differences.
Continue applying in 4’x4’ sections until complete. Only one coat is
necessary. If a second coat is desired, wait 24 hours before applying
the second coat in a direction perpendicular to the first. Occasional
touch-up may be necessary for areas subject to heavy vehicle traffic.
Rust-Oleum Decorative Color Chips (sold separately) can be added
for an upgraded appearance. Chips should be applied in 4’x4’
sections while the coating is wet.
DRY TIME
Surfaces should be ready for light foot traffic in 12-16 hours and
normal foot traffic in 24 hours. FOR FULL CURE AND VEHICLE
TRAFFIC, ALLOW 5 DAYS. Dry times increase at cooler
temperatures.
COVERAGE
Each gallon contains enough material to cover approximately 300-
400 square feet over smooth, bare concrete. Very rough or porous
surfaces will require more material.
CLEAN-UP
Wash tools and equipment with warm water and a mild detergent
immediately after use. Properly dispose of all roller covers and soiled
rags and protect unused product from freezing.