Installation Guide

ManualsBrandsUnbranded ManualsCommercial Lighting2-Light White Fluorescent Wraparound Steel Ceiling Fixture with Clear Prismatic Acrylic Lens

CAUTION: For your safety and proper operation of this fixture, read instructions

carefully before you start. Note and understand all safety information in bold print.

This fixture uses two T8 17 WATT

Medium Bipin ( 24" Length ) LAMPS.

( Sold Separately )

1) WARNING: RISK OF SHOCK

House electric current can cause painful shock or serious injury unless handled properly.

For your safety, always remember to:

-Turn off the power supply at the fuse or circuit breaker box before you install the fixture.

-Turn off the power supply again when you change lamps or perform other maintenance.

-Ground the fixture to avoid potential electric shocks and to ensure reliable starting.

-Double check all connections to be sure they are all tight and correct.

-Wear rubber-soled shoes and work on a sturdy wooden ladder.

Couper le courant au niveau du disjoncteur avant d’installer la lampe pour éviter tout risque de

secousse électrique.

2) This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also

designed to be installed in accordance with local electrical codes. If you are unsure about the

wiring, consult a qualified electrician and check your local electircal code.

Tous les branchements électrique doivent respecter les normes du Code National de l’Électricité.

Si vous ne savez pas comment installer correctement des fils électriques,appelez un électricien

professionnel.

3) WARNING: RISK OF CUTS

Some metal parts in the fixture may have sharp edges. To prevent possible cuts and scrapes,

we suggest gloves to be worn when handling all parts from this fixture.

4) Account for small parts and destroy packing material, as these may be hazardous to children.

5) WARNING: RISK OF FIRE

Most dwellings built before 1985 have supply wire rated 60°C. If supply wires are located

within 3 inches of the ballast, wire must be suitable for at least 90°C ( 194 ˚F ). Consult a

qualified electrician before installing.

Les fils d’alimentation 90℃ min.

TOOLS REQUIRED FOR INSTALLATION

A) LAMP HOUSING 1 UNIT D) WIREWAY COVER 1 UNIT A) PLIERS C) PHILPS SCREWDRIVER

B) ACRYLIC LENS 1 UNIT E) WOOD SCREWS 4 UNITS B) HAMMER D) SAFETY CLASSES

C) LAMPHOLDER 4 UNITS F) WIRENUTS 3 UNITS

INSTALLATION INSTRUCTIONS

WRAP AROUND LIGHT FIXTURE

IMPORTANT SAFETY INFORMATION

FOR YOUR PROTECTION, READ CAREFULLY

PACKING LIST

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CAUTION: For your safety and proper operation of this fixture, read instructions carefully before you start. Note and understand all safety information in bold print. WRAP AROUND LIGHT FIXTURE This fixture uses two T8 17 WATT Medium Bipin ( 24" Length ) LAMPS. ( Sold Separately ) IMPORTANT SAFETY INFORMATION FOR YOUR PROTECTION, READ CAREFULLY 1) WARNING: RISK OF SHOCK House electric current can cause painful shock or serious injury unless handled properly.
PAGE 2
INSTALLATION INSTRUCTIONS WARNING: Before wiring to the power supply, turn off the electricity at fuse or circuit breaker box. Ensure grounding to avoid potential electrical shock and to ensure reliable lamp starting. PREPARATION OF LIGHT FIXTURE FOR INSTALLATION 1) Remove the Acrylic lens from the fixture and place aside on a flat surface to avoid damage to the lens. To remove the lens, carefully slide the lens to one end of the fixture. Gently grab the lens and pull it out.
PAGE 3
INSTALLATION INSTRUCTIONS NOTE: This fixture is designed to be surfaced mounted on a drywall ceiling. Mounting hardware requirements will depend on mounting method. MOUNTING OF THE LIGHT FIXTURE A) For mounting on drywall ceilings: 1) Lift fixture housing to the ceiling, positioning the center knockout of the housing over the junction box and parallel to the ceiling. See Diagram 1. Diagram 1 2) Mark ceiling with a pencil for the drill hole locations throuth the narrow portion on the 4 keyhole slots.
PAGE 4
INSTALLATION INSTRUCTIONS WARNING: Before wiring to the power supply, turn off the electricity at fuse or circuit breaker box. Ensure grounding to avoid potential electrical shock and to ensure reliable lamp starting. WIRING OF THE LIGHT FIXTURE 1) Connect the black supply ( house ) wire to the black wire from the light fixture. Secure the connection by inserting into the wirenut, then revolving until secure.Diagram 1. 2) Connect the white supply ( house ) wire to the white wire from the light fixture.