Use and Care Manual

ZAR® Ultra Max Interior Waterborne Oil Modied Polyurethane
ZAR ULTRA MAX Waterborne Oil Modied
Polyurethane is an environmentally safe,
clear wood nish Self-leveling for a smooth
nish .is fast drying, low-odor formula
features superior hardness and mar
resistance for outstanding wear and
durability .
Natural ambering enhances wood tones.
Dual Drying Technology makes the
polyurethane dry by coalescing and oxygen
cross-linking for a harder “through cure”.
Child safe when dry. “Exotic Hardwood
Approved”-Ideal for use on Teak, Brazilian
Walnut and other exotic wood species.
Superior abrasion resistance
Low odor, fast drying
Dual Drying Technology, dries with a harder
"through cure"
Exotic hardwood approved .
Specially formulated to protect and beautify
oors, cabinets, furniture and woodwork.
Do not apply over nishes containing
stearates or aluminum oxide. Do not use steel
wool.
COMPOSITION:
Waterborne oil modied
SHEEN:
Gloss 85+ @ 60º
Semi-Gloss 65-75 @ 60º
Satin 40-50 @ 60º
Antique Flat 15-25 @ 60º
% WEIGHT SOLIDS:
31.5-33.5
% VOLUME SOLIDS:
32-34
DENSITY (LBS./US GAL.):
8.5-9.0
VISCOSITY:
54-60 KU
pH:
8.5-9.0
COLORS:
N/A
DRY TIME:
• To touch: 30 minutes
• To recoat: 2 hours
Note: Maximum cure and dry time will
be prolonged when slightly humid and
damp, cool conditions prevail.
CLEAN UP:
Warm soapy water
Dispose of contaminated absorbent,
container and unused contents in
accordance with local, state and federal
regulations.
COVERAGE (SQ. FT./US GAL.):
• 400-500 sq. ./gal.
Note: Actual coverage will vary
depending upon application method,
surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT:
4 wet mils
FLASH POINT:
N/A
SHELF LIFE:
N/A
FREEZE/THAW:
Protect from freezing
CONTAINER SIZES:
One-half pint (US), one quart (US) and
one gallon (US) cans
Does not exceed 250 g/L
N/A
May be thinned up to 10% with water for
use as a rst coat.
New Wood:Sand smooth using ne
sandpaper, vacuum sanding dust. Wipe
clean using a tack-cloth or microber cloth.
Do not use steel wool. If open-grained
woods are to be lled, use a ller that does
not contain stearates or waxes, such as ZAR
Wood Patch.
Old Clear Finishes in Good Condition:
Remove grease, dirt and wax. Sand lightly in
the direction of the grain to remove any gloss.
Do not use steel wool. Vacuum all sanding
dust. Wipe clean using a tack-cloth or
microber cloth. If the old nish contains wax
or stearates, regardless of condition, remove
completely. Clean dust with cloth dampened
with paint thinner or mineral spirits.
Old Clear Finishes in Poor Condition,
Lacquer or Shellac: Remove completely. Do
not use steel wool. Sand and vacuum all
sanding dust. Wipe clean using a tack-cloth or
microber cloth.
If wood is to be stained, use ZAR Wood Stain
or ZAR ULTRA MAX Wood Stain. Allow
Wood Stain to dry a minimum of 3 hours. For
water-based wood stains or oil-based wood
stains other than ZAR, follow manufacturer’s
drying directions.
NOTE: To ensure satisfactory results, always
prepare a sample or test the product on an
®®
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.ugl.com
Z A R ® W O O D F I N I S H I N G P R O D U C T S
O V E R
S
o
a
p
DRY TIME:
30 Minutes
Recoat 2 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
2-3 Coats
3 Coats for Floors
SPREAD RATE:
400-500 Sq.
Ft./Gallon