Use and Care Guide

SYMBOLS
AC (Alternating current) DC (Direct current)
AC/DC Voltage Negative DC
Auto-ranging Overload: Range Exceeded
Auto power off Active Hold/Capture Value
Low Battery Amperage
Voltage Non-Contact Voltage
Ohms/Resistance MicroAmps
Diode High Voltage Indication
Continuity Mega (x10
6
or 1,000,000)
Milli (x10
-3
or 0.001) Kilo (x10
3
or 1,000)
Ground Micro (x10
-6
or 0.000001)
Dangerous Levels Warning or Caution
Double Insulation
(Protection to Class II)
Safe for disconnect from
live conductors
CATEGORY DEFINITIONS
Measurement
Category
Short-Curcuit
(typical) kA
a
Location in the
building installation
II < 10 Circuits connected to mains socket
outlets and similar points in the MAINS
installation
III < 50 Mains distributions parts of the building
IV > 50 Source of the mains installation in the
building
OVERVIEW
DL469
NCV
CAT III 1000V
MAX
µA
A
CAT Ill
1000V 400A
True RMS
INSTRUCTION MANUAL
ENGLISH
DL469
AC 400A TRMS Clamp Meter
17207 • 0616
FEATURES
• True RMS
• 400A AC
• 750V AC / 600V DC
• Resistance 40MΩ
• DC Microamps 2000µA
• Diode test
• Non-contact voltage detection
• Data hold
• Manual ranging option
• Worklight
• Audible voltage indicator
• Auto power off (See select button)
• Low battery indicator
• Overmolded grip
• Test lead storage
• Battery compartment latches
• Auto-calibration
GENERAL SPECIFICATIONS
• Operating Temperature: 32˚ to 104˚F (0˚ to 40˚C)
• Storage Temperature 14˚ to 122˚F (-10˚ to 50˚C)
• Operating Humidity: <75%
• Operating Altitude: 6,562 ft (2,000m)
• Pollution Degree: 2
• Display: 3 - 3/4" digit, 4000 count
• Refresh Rate: 3/sec
• Over-range: “OL” is displayed
• Dimensions: 8.85" X 3.3" X 1.55"
• Item Weight: 0.65 lb
• Calibration: Recommended Annually
• CAT Rating: CAT III 1000V
• Certifications: cETLus 3rd Edition, CATIII 1000V, IEC 61010-1, 61010-2-032,
61010-2-033, CSA C22.2, NO. 61010-1, 61010-2-032,
61010-2-033, 6’ Drop Protection, RoHS Compliant,
CE Conformity
• Battery Type: (AAA) X 2
• Test Leads: Test lead w/Alligator Clips
• Accuracy: ± (% of reading + # of least significant digits)
IMPORTANT SAFETY WARNINGS
WARNING
Read entire Safety Notes section regarding potential hazards and proper
instructions before using this meter. In this manual the word “WARNING” is
used to indicate conditions or actions that may pose physical hazards to the
user. The word “CAUTION” is used to indicate conditions or actions that may
damage this instrument.
WARNING
To ensure safe operation and service of the tester, follow these instructions.
Failure to observe these warnings can result in severe injury or death.
WARNING
• Before each use, verify meter operation by measuring a known voltage
or current.
• Never use the meter on a circuit with voltages that exceed the category
based rating of this meter.
• Do not use this meter during electrical storms or in wet weather.
• Do not use the meter or test leads if they appear damaged.
• Ensure meter leads are fully seated and keep fingers away from the
metal probe contact when making measurements. Always grip the leads
behind the finger guards molded into the probe.
• Do not open the meter to replace batteries while the probes are
connected.
• Use caution when working with voltages above 60V DC or 25V AC RMS.
Such voltages pose shock hazards.
• To avoid false readings that can lead to electrical shock, replace
batteries if a low battery indicator appears.
• Unless measuring voltage or current, shut off and lockout power before
measuring resistance or capacitance.
• Always adhere to national and local safety codes. Use proper personal
protective equipment (PPE) to prevent shock and arc blast injury where
hazardous live conductors are exposed.
• Always turn off power to a circuit or assembly under test before cutting,
unsoldering or breaking the current path. Even small amounts of current
can be dangerous.
• Always disconnect the live test lead before disconnecting the common
test lead from the circuit.
• In the event of electrical shock, ALWAYS bring the victim to the
emergency room for evaluation, regardless of victim’s apparent recovery.
Electrical shock can cause unstable heart rhythms that may need
medical attention.
• If any of the following occur during testing, turn off the power source to
the circuit being tested: arching, flame, smoke, extreme heat, smell of
burning materials or discoloration or melting of components.
WARNING
Higher voltages and currents require greater awareness of physical safety
hazards. Before connecting the test leads, turn off power to the circuit under
test, set meter to the desired function and range, connect the test leads to
the meter first, then connect to the circuit under test. Reapply power. If an
erroneous reading is observed, disconnect power immediately and recheck all
settings and connections.
WARNING
This meter is designed for trade professionals who are familiar with the
hazards of their trade. Observe all recommended safety procedures that
include proper lock-out utilization and use of personal protective equipment
that includes safety glasses, gloves and flame resistant clothing.
WARRANTY
The DL469 is warranted to be free from defects in materials and workmanship
for a period of two years from the date of purchase. If within the warranty
period your instrument should become inoperative from such defects, the unit
will be repaired or replaced at UEi’s option. This warranty covers normal use
and does not cover damage which occurs in shipment or failure which results
from alteration, tampering, accident, misuse, abuse, neglect or improper
maintenance. Batteries and consequential damage resulting from failed
batteries are not covered by warranty.
Any implied warranties, including but not limited to implied warranties of
merchantability and fitness for a particular purpose, are limited to the express
warranty. UEi shall not be liable for loss of use of the instrument or other
incidental or consequential damages, expenses, or economic loss, or for any
claim or claims for such damage, expenses or economic loss.
A purchase receipt or other proof of original purchase date will be required
before warranty repairs will be rendered. Instruments out of warranty will be
repaired (when repairable) for a service charge
For more information on warranty and service, contact:
www.ueitest.com • Email: [e-mail]
1-800-547-5740
This warranty gives you specific legal rights. You may also have other rights,
which vary from state to state.
DISPOSAL
CAUTION: This symbol indicates that equipment and its accessories
shall be subject to separate collection and correct disposal.
CLEANING
Periodically clean your meter’s case using a damp cloth. DO NOT use abrasive,
flammable liquids, cleaning solvents, or strong detergents as they may damage the
finish, impair safety, or affect the reliability of the structural components.
STORAGE
Remove the batteries when instrument is not in use for a prolonged period of time.
Do not expose to high temperatures or humidity. After a period of storage in extreme
conditions exceeding the limits mentioned in the General Specifications section, allow
the instrument to return to normal operating conditions before using it.
Copyright © 2016 UEi. All Rights Reserved.
1000V
CAT III
A. Clamp: Measure inductive AC current. Opens to 1.25” (31.7mm).
B. Conductor Alignment Marks: Used to aid the visual alignment of a conductor
when measuring inductive amperage. Greatest accuracy is achieved when the
conductor inside the clamp is centered at the intersection of these marks.
C. Wire Separation Tab/NCV sensor: Used to isolate an individual wire from a
bundle for testing. NCV sensor detects live voltage.
D. Test Lead Holder: Used for hand-free use of the test probes.
E. Worklight: Lights clamp area in dark work environments.
F. Category Max Indicator: Maximum CAT Rating for Clamp/jaw.
G. Hand Guide: Used as a point of reference for the operator’s safety.
H. NCV Alert Light: Indicates voltage when in NCV mode.
I. Clamp Lever: Opens and closes current clamp jaw. Do not allow fingers or
objects to become pinched in the base as the jaw closes.
J. Hold Button
• Press to hold the reading on the display. Press again to return to live reading.
• Press and hold to turn on Worklight. Press and hold again to turn off.
K. Function Dial: Turns on meter and is used to select the function.
L. Select Button
• Used to choose measurement mode from a single dial selection;
AC or DC volts, Resistance or Continuity.
• Press and hold the button while turning the meter on to disable Apo
(auto power off).
M. Range Button:
• Press repeatedly to cycle through manual ranges
• Press and hold to return to auto ranging mode
• AT is displayed on LCD only during auto ranging mode
N. Apo: Auto power off after 30 minutes of use. Press and hold "select" button while
turning the meter on to disable Apo. (Auto power off)
O. Display:
• High contrast display.
P. Category Max Indicator: Maximum CAT Rating for input jacks.
Q. Input Jacks: Multifunction and Common jacks
• Multifunction input port used for measuring: AC or DC volts, Resistance,
Continuity, Diode and DC µA.
• Use CAT III test leads or higher.
R. Serial Number
S. Battery Cover: Easy access for replacing batteries.
T. Battery Cover Latches: Convenient, quick opening
U. Test lead holders: For storing test leads when not in use.
S / N :
OPEN
LOCK
OPEN
LOCK
R
S
T
U
DL469
NCV
CAT III 1000V
MAX
µA
A
CAT Ill
1000V 400A
True RMS
C
D
J
G
K
M
O
N
P
Q
A
F
H
I
L
E
B
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com