Specification

ManualsBrandsTyRap ManualsKitchen11 in. Cable Tie - White (100 per Bag)

Thomas and Betts Corporation

Product Guide Specification

WIRE AND CABLE FASTENING

26 05 84-1

REVISION 0

Specifier Notes: This product guide specification is written according to the Construction Specifications Institute

(CSI) 3-Part Format, including MasterFormat, SectionFormat, and PageFormat, as described in The Project

Resource Manual—CSI Manual of Practice, Fifth Edition.

This section must be carefully reviewed and edited by the Architect or Engineer to meet the requirements of the

project and local building code. Coordinate this section with other specification sections and the Drawings. Delete

all “Specifier Notes” after editing this section.

Section numbers are from MasterFormat 2010 Update.

SECTION 26 05 84

WIRE AND CABLE FASTENING

Specifier Notes: Delete any information below in Parts 1, 2 or 3 which is not required or relevant for the project.

PART 1 – GENERAL

1.01 SUMMARY

A. This section Includes the following products for bundling or harnessing wire and cable:

1. Standard Nylon 6.6 Cable Ties

2. UV Resistance Nylon 6.6 Cable Ties

3. Detectable Cable Ties

4. Flame Retardant Nylon 6.6 Cable Ties

5. Weather Resistant Nylon 12 Cable Ties

6. Heat Stabilized Nylon 6.6 Cable Ties

7. Heat Stabilized/UV Resistant Nylon 6.6 Cable Ties

8. Extra High Temperature Nylon 4.6 Cable Ties

9. Weather and Chemical Resistant Polypropylene Cable Ties

10. Low Smoke Fluropolymer Cable Ties

11. Radiation Resistant Fluoropolymer Cable Ties

12. Dual Locking Stainless Steel Cable Ties

13. Deltec® Cable Support System

1.02 REFERENCES

A. Underwriters Laboratories, Inc. (UL):

1. UL1565: Positioning Devices

B. Canadian Standard Association (CSA):

1. CSA C22.1 Canadian Electrical Code Part I (CEC)

2. CSA C22.2 No.18.5 Wiring Position Devices

C. International Electrotechnical Commission

1. IEC 62275 Cable Management Systems

D. National Fire Protection Association (NFPA)

1. NFPA 70 National Electrical Code (NEC)

1.03 SUBMITTALS

A. Comply with Section 01 33 00 – Submittal Procedures.

Summary of content (6 pages)

PAGE 1
Thomas and Betts Corporation Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat, and PageFormat, as described in The Project Resource Manual—CSI Manual of Practice, Fifth Edition. This section must be carefully reviewed and edited by the Architect or Engineer to meet the requirements of the project and local building code.
PAGE 2
Thomas and Betts Corporation Product Guide Specification 1.04 1.05 B. Product Data: 1. Submit manufacturer’s descriptive literature and product specifications for each product. 2. Manufacturer’s product drawings. C. Manufacturer’s installation instructions. QUALITY ASSURANCE A. Manufacturer Qualifications: Products shall be free of defects in material and workmanship. B. Furnished products are listed, recognized or classified by third party agencies as being suitable for the intended purpose.
PAGE 3
Thomas and Betts Corporation Product Guide Specification 9. 10. Standard nylon 6.6 cable ties shall be suitable for use in air handling spaces (plenums) in accordance with section 300.22 (C) and (D) of the NEC and rules 12-010(3), (4) and (5), and 12-020 of the CEC. Standard nylon 6.6 cable ties shall be UL Listed and CSA Certified. B. UV Resistant nylon 6.6 cable ties (TY523MX series): 1. UV Resistant nylon 6.6 cable ties shall be molded from nylon 6.6 material. 2. UV Resistant nylon 6.
PAGE 4
Thomas and Betts Corporation Product Guide Specification 4. 5. 6. 7. 8. 9. Heat stabilized nylon 6.6 cable ties shall have a turned up tail. Heat stabilized nylon 6.6 cable ties shall be light green in color. Heat stabilized nylon 6.6 cable ties shall be rated for 221ºF (105ºC) maximum. Heat stabilized nylon 6.6 cable ties shall have a UL94V-2 flame rating. Heat stabilized nylon 6.6 cable ties shall have a tensile strength rating of 18 lbs, 30 lbs, 40 lbs, 50 lbs and 120 lbs.
PAGE 5
Thomas and Betts Corporation Product Guide Specification 9. 10. Low smoke fluoropolymer cable ties shall have a tensile strength rating of 18 lbs and 50 lbs. TYV series shall be UL Listed. K. Radiation Resistant Fluoropolymer Cable Ties (TYZ series): 1. Radiation resistant cable ties shall be molded from fluoropolymer material. 2. Radiation resistant fluoropolymer cable ties shall have a non-magnetic stainless steel locking device. 3.
PAGE 6
Thomas and Betts Corporation Product Guide Specification B. Unless otherwise specification all cable ties will be installed with one of the following tools: 1. ERG50 hand tool 18 to 50 lbs tensile strength cable ties 2. ERG50P pneumatic tool 18 to 50 lbs tensile strength cable ties. 3 ERG120 hand tool 50 to 120 lbs tensile strength cable ties.