User's Manual

ManualsBrandsTVLogic ManualsMonitors5.5" IPS On-Camera Monitor with L-Series Type Plate

Field Production Monitor

F-5A

Summary of content (44 pages)

PAGE 1
Field Production Monitor Operation Manual_V1.
PAGE 2
PAGE 3
1. Caution ........................................................................................ 2. Main Features ............................................................................... 3. Controls & Functions ..................................................................... 4. Menu Tree & Adjustment ............................................................... 5. Menu Operations .......................................................................... [1] Picture .........................
PAGE 4
1. Caution • Always use set voltage. (DC 6V 1.25A/34V 0.27A) • When using outdoors, use the product after waterproofing measures. • When using a DC Adapter other than the FHD Viewfinder Monitor 4 one supplied by the manufacturer, please be advised that the adapter with DC 12V/3A ~ 6A can be compatible with the monitor. • All operating instructions must be read and understood before the product is operated.
PAGE 5
1. Caution • Do not use the product near water, such as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement. • Keep the product away from direct rays of the Sun-light. • Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product.
PAGE 6
2. Main Features F-5A Monitor contains the following features : • Compatible with various SDI signals formats (SD/HD/3G) - This product is compatible with various SDI signals - 480i, 576i, 720p, 1080i, 1080p, 1080psf • HDMI(with HDCP) Signal FHD Viewfinder Monitor 6 - This product is compatible with various HDMI signals.
PAGE 7
3.
PAGE 8
3. Controls & Functions TOP • [MENU/EXIT/SOURCE] Button - Used to activate the OSD menu. - When the OSD menu is activated, press this button to exit from the menu. - Press the button for more than 2 seconds to activate Input Select menu. (SDI, HDMI) - Use the [ENCODER] Knob to change the Input Signal. FHD Viewfinder Monitor 8 • [UP/DOWN/ENTER] Knob - Used to move within the menu when OSD menu is activated, and is also used to decrease or increase the value of the selected feature.
PAGE 9
3. Controls & Functions REAR • [HDMI IN] • [REAR TALLY] • [HDMI OUT] • [DC POWER / TALLY] (XLR 4P) - Signal input terminal for HDMI signal. - Signal output terminal for HDMI signal. - Video source from SDI input terminal can be converted to HDMI format. • [HEADPHONE] (Phonejack) - Used for Stereo Audio Output through Phone Jack. (video signals with embedded audio only) - Activates same as [SCREEN TALLY].
PAGE 10
4. Menu Tree & Adjustment [1] Menu Tree [3] Menu Control Sequence • OSD(On-Screen Display) Menu helps to use varous different functions. • This Picture is the menu structure for F-5A.
PAGE 11
5. Menu Operations [1] PICTURE F-5A +90 +90 +90 +24 +24 UNLOCK DEFAULT SYNCHRONIZATION NONE01 NONE01 NONE01 • KNOB LOCK - Locks the Knob control. • 3DLUT SYNC - Used to load a list of available 3DLUT files currently stored in the FLASH MEMORY. - Available 3DLUT formats are Cube, GV Lut, Quantel, Davinci and Assimilate Scratch. - Available sizes of the 3DLUT are 17 or 33. • 3DLUT IMPORT 1/2/3 • BRIGHTNESS - Used to set the brightness(=offset) level from -100 to 100.
PAGE 12
5. Menu Operations [2] COLOR FHD Viewfinder Monitor 12 COLOR같이 STANDARD VIDEO RANGE PEAK LUMINANCE BLACK LEVEL COLOR GAMUT COLOR TEMP EOTF LOCAL DIMMING EETF HLG SG SG CAM LUT CAM LUT THROUGH F-5A UHD NARROW 100 0.001 BT.2020 6500K 2.4 OFF OFF OFF OFF OFF PAGE(1/2) • STANDARD - Used to select the color and dynamic rage of the screen. - Available options are HD, UHD, DCI-P3, PQ, HLG, SLog3 and User1/2/3. # The submenus may be activated in the User1/2/3 mode only.
PAGE 13
5. Menu Operations [2] COLOR STANDARD VIDEO RANGE PEAK LUMINANCE BLACK LEVEL COLOR GAMUT COLOR TEMP EOTF LOCAL DIMMING EETF HLG SG SG CAM LUT CAM LUT THROUGH F-5A UHD NARROW 100 0.001 BT.2020 6500K 2.4 OFF OFF OFF - Used to change the Camera LUT. - Available LUTs are LOG-C, C-LOG, S-LOG 1,2,3 and REDGamma 3,4. • CAM LUT THROUT (Camera LUT Throughout) - Apply the currently applied LUT to Throughout.
PAGE 14
5. Menu Operations [2] COLOR COLOR같이 FHD Viewfinder Monitor 14 TEMP COLOR GAIN RED GAIN GREEN GAIN BLUE BIAS RED BIAS GREEN BIAS BLUE COLOR COPY COLOR SPACE F-5A 6500K_60P BT.709 +90 +90 +90 +90 +90 +90 +90 +90 +90 PAGE(2/2) • TEMP COLOR (Color Temperature) - Controls the color temperature and allows instant access to preset the color temperature settings. - Available color temperatures are 6500K, 9300K and User1/2/3.
PAGE 15
5. Menu Operations [3] MARKER ENABLE MARKER CENTER MARKER SAFETY AREA FIT MARKER MARKER MAT MARKER COLOR THICKNESS USER MARKER H1 USER MARKER H2 USER MARKER V1 USER MARKER V2 GRID ENABLE GRID TYPE GRID THICKNESS GRID THROUGHOUT F-5A ON OFF OFF OFF OFF OFF WHITE 2 + 0 +1920 + 0 +1080 OFF OFF 2 OFF • ENABLE - Used to activate the Marker function. • MARKER - Available Marker types are OFF, 16:9, 4:3, 4:3 ON AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1 & 4:3 and USER.
PAGE 16
5. Menu Operations [3] MARKER FHD Viewfinder Monitor 16 MARKER같이 ENABLE MARKER CENTER MARKER SAFETY AREA FIT MARKER MARKER MAT MARKER COLOR THICKNESS USER MARKER H1 USER MARKER H2 USER MARKER V1 USER MARKER V2 GRID ENABLE GRID TYPE GRID THICKNESS GRID THROUGHOUT F-5A ON OFF OFF OFF OFF OFF WHITE 2 - Used to activate the GRID display function. • GRID TYPE - Used to select the GRID type. - Available GRID types are 3x3, 4x4, 5x5 and 6x6.
PAGE 17
5. Menu Operations [4] VIDEO F-5A SCAN ZERO SCAN ASPECT 16:9 H/V DELAY OFF BLUE ONLY OFF USER ASPECT HOR USER ASPECT VER 3G FORMAT NORMAL H/V FLIP OFF ZOOM OFF ZOOM SPLIT OFF + + 0 0 • BLUE ONLY - Used to switch in the order of [Off]-[Blue Only][Mono]-[Off]. - Press the button to remove red and green components from the input signal and display blue componet only. - Press the button again to switch to monochrome mode which has no chroma signal.
PAGE 18
5. Menu Operations FHD Viewfinder Monitor 18 [4] VIDEO VIDEO이 F-5A SCAN ZERO SCAN ASPECT 16:9 H/V DELAY OFF BLUE ONLY OFF USER ASPECT HOR USER ASPECT VER 3G FORMAT NORMAL H/V FLIP OFF ZOOM OFF ZOOM SPLIT OFF + + 0 0 PAGE(1/2) • H/V FLIP - Allows the displayed image to be flipped horizontally or vertically. - This feature provides flexible mounting options for camera operators.
PAGE 19
5. Menu Operations [4] VIDEO DSLR DSLR SCALE TIMECODE FOCUS ASSIST FOCUS AS COLOR FOCUS AS LEVEL SCR TALLY SCR OP LEVEL SCR TALLY COL LOW BAT DIS F-5A CANON 7D LIVE VIEW OFF OFF RED + 90 OFF LOW RED OFF PAGE(2/2) • DSLR - Select the DSLR camera to be used with the monitor. Available mode is [CANON 7D]. * DSLR cameras’ screen size and aspect ratio of Live / Record / Playback modes vary depending to their manufacturer. • DSLR SCALE - This is a special function for CANON/NIKON DSLR cameras.
PAGE 20
5. Menu Operations [4] VIDEO VIDEO이 FHD Viewfinder Monitor 20 DSLR DSLR SCALE TIMECODE FOCUS ASSIST FOCUS AS COLOR FOCUS AS LEVEL SCR TALLY SCR OP LEVEL SCR TALLY COL LOW BAT DIS F-5A CANON 7D LIVE VIEW OFF OFF RED + 90 OFF LOW RED OFF PAGE(2/2) • SCR TALLY (Screen Tally) - Used to set Tally operation according to the input level of TALLY IN terminal which is among the terminals of XLR 4P connector in the rear. • SCR TALLY LEVEL (Screen Tally Level) - Used to set the input level of Tally operation.
PAGE 21
5. Menu Operations [5] WAVEFORM ENABLE TYPE INTENSITY TRANS SIZE LINE WAVEOFORM SEL LINE POS LUMA CHECK LUMA ADJUST RANGE ERROR Y MAX Y MIN C MAX C MIN Y PICTURE BLINK C PICTURE BLINK F-5A OFF OFF + 90 OPAQUE SAMLL OFF + 90 OFF + 90 OFF + + + + 90 90 90 90 OFF OFF • ENABLE - Used to activate/ deactivate the Waveform which is selected in the Waveform/Vector Type menu. • TYPE - This function sets the Waveform and Vectorscope. Available options are different according to the Input signal.
PAGE 22
5. Menu Operations [5] WAVEFORM FHD Viewfinder Monitor 22 WAVEFORM ENABLE TYPE INTENSITY TRANS SIZE LINE WAVEOFORM SEL LINE POS LUMA CHECK LUMA ADJUST RANGE ERROR Y MAX Y MIN C MAX C MIN Y PICTURE BLINK C PICTURE BLINK F-5A OFF OFF + 90 OPAQUE SAMLL OFF + 90 OFF + 90 OFF + + + + 90 90 90 90 OFF OFF • LUMA CHECK - Displays the Luma(Y’) level of the input image in colors. - Can select between [Color Pattern] or [Zebra Pattern].
PAGE 23
5. Menu Operations [5] WAVEFORM WAVEFORM F-5A OFF OFF + 90 OPAQUE SAMLL OFF + 90 OFF • Y PICTURE BLINK - Used to set whether or not to blink pixels with values exceeding Y MAX and Y MIN. • C PICTURE BLINK - Used to set whether or not to blink pixels with values exceeding C MAX and C MIN. + 90 OFF + + + + 90 90 90 90 OFF OFF • Y MAX - Used to set the maximum Luma(Y’) level from 0 to 255. - Pixels with values exceeding the max Y’ level will blink on the screen, and be displayed in red on the Waveform.
PAGE 24
5. Menu Operations FHD Viewfinder Monitor 24 [6] AUDIO AUDIO F-5A VOLUME AUD LEFT AUD RIGHT LEVEL METER LVM DISPLAY LVM REFERENCE LVM SIZE PEAK DECAY TIME + 90 OFF FOF OFF PAIR -18dB SMALL + 90 • LVM DISPLAY (Level Meter Display) - Used to set the display method for audio level meter. - Available modes are Group and Pair. * In the HDMI mode, the mode is set to Pair. • LVM REFERENCE (Level Meter Reference) - Display the default audio level meter value, - Available options are -18dB and -20dB.
PAGE 25
5. Menu Operations [7] SYSTEM F-5A DEFAULT LUMINANCE INTERNAL PAT DISPLAY ENABLE ECO SAVING FAST MODE EXTERNAL FAN SW UPGRADE OFF + 48 VERSION SERIAL NUM SW 00 FPGA 00 BOARD 00 12345678 OFF ON ON OFF OFF OFF • FAST MODE - Used to minimize the de-interlacing processing time delay and improves the quality of fast moving and fine details under interlaced format. - Since the function of this feature is to minimize the de-interlacing delay, it will not be effective under progressive format.
PAGE 26
5. Menu Operations [7] SYSTEM FHD Viewfinder Monitor 26 SYSTEM F-5A DEFAULT LUMINANCE INTERNAL PAT DISPLAY ENABLE ECO SAVING FAST MODE EXTERNAL FAN SW UPGRADE OFF + 48 VERSION SERIAL NUM SW 00 FPGA 00 BOARD 00 12345678 OFF ON ON OFF OFF OFF • S/W UPGRADE - Used to upgrade the firmware using USB (Thumb drive). * See section “7. Other Functions -> [13] Firmware Upgrade” for more information. • VERSION - Displays current firmware version.
PAGE 27
6. Button Functions SDI HDMI NO VIDEO • F-5A unit is capable of processing SDI / HDMI Input signal. 1. Press the[MENU
PAGE 28
7. Other Functions [1] User Aspect USER ASPECT WIDTH +1920 HEIGHT +1080 • Used to adjust the Width /Height display ratio. 1. Select [Aspect] mode in the OSD menu by pressing the function button on the right top of the monitor to activate the [USER ASPECT] mode. FHD Viewfinder Monitor 28 2. After the activation, press the Knob to begin controlling. Adjust the ratio using the knob. - Adjust the ratio using the Knob. - Control range for width: 0~1920. - Control range for height : 0~1080.
PAGE 29
7. Other Functions [2] Waveform / Vectorscope - Displays the Luma(Y’) component of the input signal into waveform. • VectorScope - Displays the color components ‘B-Y’ and ‘R-Y’ of the input signals onto the X-Y axis. - Two different types of Vetorscopes are displayed according to SD or HD input signals. - 100% and 75% scales are indicated on the Vetorscope. FHD Viewfinder Monitor 29 • Waveform Y • Waveform Cb, Cr - Displays the Cb, Cr components of the input signal into waveform.
PAGE 30
7. Other Functions [3] Line Select (Waveform/VectorScope) FHD Viewfinder Monitor 30 • Used to select specific Vertical Line for WaveForm/VectorScope. [4] Zoom • Used to magnify the input signal from 0% to 90%. - This is available when LINE WaveForm is activated. - Supports Zoom Width Scroll / Zoom Height Scroll function. - To activate this feature, go to [Waveform]- [Waveform/Vector]-[Line Waveform]- [Select Line Position] and use the Knob to select a vertical line.
PAGE 31
7. Other Functions [5] Luma(Y’) Zone Check - Displays the Luma(Y’) level of the input image in colors. - Y’ ≥ 100% : Pixels with higher Y’ level than 100 turn to red. - Y’ ≤ 0% : Pixels with lower Y’ level than 0 turn to green. - Pixels with Y’ levels designated by the user are displayed in following colors - yellow, pink, cyan. - Factory Default Y’ (Border line between pink and yellow) level is 75% and the pink color is assigned to pixels with Y’ level from 70% to 75%.
PAGE 32
7. Other Functions [6] Focus Assist • Focus Assist function assigns a color to the pixels in the shape or the boundary of the image to inform the user to achive the best focus. Viewfinder Monitor 32 - With this function, user can easily differenciate the focused area from the out-focused area especially when shooting with a shallow depth of field. - Available types are [Mono] and [Color] types. * [Mono] : Background image is mono type. * [Color] : Background image is original color type.
PAGE 33
7. Other Functions [8] DSLR Scale • This function is designed for some DSLR cameras of Canon(7D) that output different resolution from the operation mode (StandBy, Record, Play Back) • Select the Camera model in the [Display/ Vide]- [DSLR Camera Sel.] menu. - In StandBy mode of Canon 5D Mark II, 1080i of HD resolution is indicated. However, real output resolution is 1620x1080 so blank area is displayed on the screen because the 16:9 aspect ratio is not realized.
PAGE 34
7. Other Functions [9] HDMI To SDI Conversion-Out • Video source from ‘HDMI input’ terminal can be output through ‘SDI throughout’ terminal. [10] SDI To HDMI Conversion-Out ●● 3G/HD/SD SDI signals from‘SDI input’ terminal can be output through‘HDMI out’terminal. Output Format Viewfinder Monitor 34 ※Note: HDSLR camera manufacturers usually specify the resolution and frame rate for the recording. The signal format that is output through HDMI terminal of cameras may differ from makers to makers.
PAGE 35
7. Other Functions [11] Screen Tally/Rear Tally [12] Internal Pattern • Activates with the Rear Tally on the rear of the monitor at the same time. • Displays internally generated test patterns. - The pattern consists of ColorBar and Pluge+ Grayscale Patterns. Full screen colors of various gray levels(0~100%) are also embedded. • Screen TALLY Operating Level - Used to set the input level of Tally operation. (Open&Low : less than 0.6V, High : more than 2.
PAGE 36
FHD Viewfinder Monitor 36 7. Other Functions [13] ARRI Camera Status [14] Firmware Upgrade • Used to display the camera status information provided by ARRI ALEXA camera on the OSD. • The USB(Thumb drive) which contains the F/W file is needed for Firmware Upgrade. • Select the SW UPGRADE in the SYSTEM menu.
PAGE 37
8. Available Signal Formats Input Signal VIDEO PC 480 / 59.94i (NTSC) 480 / 60p 576 / 50i (PAL) 576 / 50p 720 / 23.98p 720 / 24p 720 / 25p 720 / 30p 720 / 50p 720 / 59.94p 720 / 60p 1080 / 23.98PsF 1080 / 24PsF 1080 / 25PsF 1080 / 23.98p 1080 / 30PsF 1080 / 29.97PsF 1080 / 24p 1080 / 25p 1080 / 29.97p 1080 / 30p 1080 / 50i 1080 / 50p 1080 / 59.94i 1080 / 60i 1080 / 59.
PAGE 38
9. Video Support Resolution VIDEO Support Resolution Input Signal Interfaces FHD Viewfinder Monitor 38 SD SDI single link Input Signal Interfaces 3G-SDI (A/B) single link Input Signal Interfaces HD SDI single link Input Signal Interfaces HD SDI single link Signal Foramt (SD SDI) 720x487 (59.94i) 720x576 (50i) YCbCr 4:2:2 10bit Signal Format (3G SDI) 1920x1080 (60p/59.94p/50p) YCbCr 4:2:2 10bit 1920x1080 (30/29.97/25/24/23.98/ 30sF/29.97sF/25sF/24sF/23.
PAGE 39
10. Product Specifications LCD Input Output Input Signal SDI Input Signal Formats 5.5” Resolution 1920×1080(16:9) Pixel Pitch 0.0213(W) x 0.0639(H) mm Color Depth 16.7M (True) Viewing Angle H : 160 degrees / V : 160 degrees Luminance of white 500 cd/ m2 (Center) Contrast Ratio 1,000 : 1 Display Area 122.7(H)x69.0(V) mm 1 X HDMI HDMI V1.
PAGE 40
11. Optional Accessories FHD Viewfinder Monitor 40 Model Product Description BH-1 Ball Head for VFM-058W, 055A / F-7H / F-7H mk2 TH-Mount 05 Camera Mount for VFM-056WP, 058W, 055A / F-7H / F-7H mk2 TH-Mount-F7H Camera Mount for F-7H / F-7H mk2 (Screw head length 20mm) BA-055E Battery Adapter for VFM-055A / F-5A (Canon LP-E6 Series; DSLR EOS 5D/7D; Single type of BB-055E) BA-055B Battery Adapter for VFM-055A / F-5A (Panasonic CGR-D16.
PAGE 41
11.
PAGE 42
11.
PAGE 43
PAGE 44
FOR MORE INFORMATION PLEASE VISIT : http://www.tvlogic.tv 부사장 12F, ACE HIGH-END 8, 345-4 Gasan-dong, Geumcheon-gu, Seoul, 08590, KOREA TEL : +82-70-8668-6611, FAX : 82-2-6123-3201, E-mail : sales@ t vlogic.co.kr 153-802 서울특별시 금천구 가산동 345-4 조 성 일 Mobile.