Installation Instructions
Table Of Contents
- 页 1
- 书签07C0074E For Models : 673-6229, 673-6230
- 书签9C78DF23 673-6231
- 书签05A10793 Single Handle Pull-Down Kitchen Faucet with Soap Dispenser
- 书签15AF67A8 Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft damp cloth. Avoid abrasive cleaners, steel wool, and harsh cleaners at these will dull the finish and void the warranty. Vinegar is suggested as an alternative cleaner and is safe for all finishes.
- 书签ECB5A8F2 If soldering during the installation of this faucet, remove the seats, cartridges, and washers before adding any heat. The warranty will be voided on these parts if not removed before soldering.
- 书签DC2E92A3 Safety glasses should always be worn when cutting or soldering.
- 书签CC78DE83 Always cover your drain before installation to prevent losing parts.
- 书签49F766E7 TUSCANY
- 书签CB9C34D6 Before installation turn off the cold and hot water shut offs. Turn the faucet handle\(s\) on to release the pressure in the system. Before installing the water supply lines to the new faucet, turn on both water supply valves and bleed the water supply lines into a bucket for one minute to remove any debris that could clog the faucet. Wrap ALL threaded connections with Teflon tape in a clockwise direction. When installing the new faucet, turn the connectors finger tight, then use an adjustable wrench to tighten the connectors. Connections that are too tight will reduce the integrity of your system.
- 书签136BA54F Flashlight
- 书签F1736BF3 Safety Glasses
- 书签D1665E37 Groove Joint Pliers
- 书签3DB464CB Vacaville
- 页 2
- 书签4CB080F1 Pump
- 书签9D3F65FC Soap Dispenser Base
- 书签57663054 Small Washer
- 书签6C17DB95 Lock Nut
- 书签1A42F5FA Bottle
- 书签E76177CB Gasket Assembly
- 书签B782F9AF Screen Washer
- 书签03C72E63 Handle
- 书签1B411B1F Handle Button
- 书签B9DF2AE7 Set Screw
- 书签EBE0ABAD Trim Cap
- 书签566C9ED0 Lock Nut
- 书签7FB0EBCE Cartridge
- 书签8D66D54E Cartridge Cover
- 书签59EACDCD Spray Head
- 书签E96D07C0 Hose
- 书签19BF0FC4 Quick Connect Clip
- 书签08AF77DF Hose Guide
- 书签D751239D Spout
- 书签2FC27EB9 Rings
- 书签261D0DEC O-ring
- 书签479C6395 Spout Connector
- 书签F879F0B5 Secured Sleeve
- 书签68F17E91 Decorative Connector Nut
- 书签41E29263 Body
- 书签7E4F77B8 Hose Protector
- 书签695E5FDC Waterway
- 书签0FBBC583 Valve
- 书签4D4A58B2 Quick Connect Assembly
- 书签A9F68F1E O-ring
- 书签278946F5 Deck Plate
- 书签48BEA139 Gasket
- 书签7D9E135C Threaded Shank
- 书签74EF7067 Rubber Washer
- 书签E51E7459 Metal Washer
- 书签3736ECF4 Lock Nut
- 书签4FC25444 Screws
- 书签62F6BA2A Hose Protector
- 书签3CA3FC84 Allen Wrench
- 书签FFD3F75F Weight
- 书签95056718 No.
- 书签E8EF80BC Part Name
- 书签AAB0BCE1 1
- 书签848D703F 2
- 书签ABCEB7F3 3
- 书签995E2EF8 4
- 书签52B8CC46 5
- 书签CB78667A 6
- 书签503BD5BB 7
- 书签C05B030F 8
- 书签CA7D5789 9
- 书签9D77D681 10
- 书签29A27915 11
- 书签19433C0B 12
- 书签CD93AE89 13
- 书签D93790A6 14
- 书签C120AF07 15
- 书签239BF11F 16
- 书签4900E47F 17
- 书签9952B4B5 18
- 书签F1D2BB66 19
- 书签0AA7AB4D 20
- 书签227CBEF6 21
- 书签35885750 22
- 书签594330F5 23
- 书签94519B4C 24
- 书签E82A4838 25
- 书签C0FF4B26 26
- 书签8FEDF5A4 27
- 书签EC5BE663 28
- 书签D75E57DA 29
- 书签B5957390 30
- 书签940D73CA 31
- 书签D28D8C7B 32
- 书签BF027D62 33
- 书签52900080 34
- 书签1A5A71C8 35
- 书签B6B396E5 36
- 书签5A224DD9 37
- 书签94F185B2 38
- 书签26F331EA 39
- 书签CC84F0C1 40
- 书签353BF728 41
- 书签4C56F1C4 35
- 书签946AD620 36
- 书签2B8C685D 37
- 书签05BC2D91 39
- 书签E3D5C9AB 34
- 书签EE0A564F 1
- 书签6395A0AF 2
- 书签766DF70B 3
- 书签D4196850 4
- 书签351D781A 5
- 书签7F86827A 6
- 书签1C77EB8B 7
- 书签3912FB18 8
- 书签FF581000 9
- 书签1668B767 10
- 书签13249DE1 11
- 书签E253E96F 12
- 书签AD135441 13
- 书签5909C30C 14
- 书签AF4626FA 15
- 书签E16E879F 16
- 书签35DAE2AC 17
- 书签1F6FC336 18
- 书签03C2082D 19
- 书签C0669ECC 20
- 书签A86980E7 21
- 书签8AD78D3A 22
- 书签C612131C 23
- 书签2692AF32 24
- 书签19A530B8 25
- 书签7C8B05DF 32
- 书签16C7DA6E 33
- 书签15D9D77E 13
- 书签6F530163 38
- 书签825C4AA7 Large Washer
- 书签D137C4FA 26
- 书签FA221BD6 27
- 书签F89381B0 28
- 书签69374160 29
- 书签37CC1072 30
- 书签7AC968D7 31
- 书签7CAEF281 40
- 书签D1EDC7FD 41
- 页 3
- 书签BB9F5C79 2. Remove the lock nut \(#29\) and gasket assembly \(#40\) from the threaded shank \(#26\). Note: Do not remove the customer service tag with the model number and phone number. This information will be needed when calling the customer service department.
- 书签2A9823D1 Step 1-3
- 书签161D2555 40
- 书签0206FBDE 29
- 书签724CF034 1. Before installation turn off the cold and hot water shut offs. Turn the faucet handle\(s\) on to release the pressure in the system. Remove the current faucet. Thoroughly clean and dry the surface the new faucet will be installed on. Note: This faucet fits 3.8cm/ 1-1/2" countertops.
- 书签F2E288E2 3. Deck Plate \(3 Hole\) Installation: Verify the O-ring \(#23\) is in place. Attach the gasket \(#25\) to the deck plate \(#24\), ensuring the notches on the deck plate \(#24\) line up for proper installation. Install assembled pieces to the faucet. Apply silicone sealant beneath the gasket \(#25\). Install the faucet through the second hole from the left. Single Hole Installation: Verify the O-ring \(#23\) is in place. Apply silicone sealant beneath the body \(#18\). Install the faucet through the single faucet hole.
- 书签3941E759 18
- 书签B3A654B7 18
- 书签4AA9FF5C 26
- 书签62DB64A6 23
- 书签2E4CCAA1 24
- 书签256E4493 25
- 书签8B88BA9C 23
- 页 4
- 书签7B982A8E Installation Instructions
- 书签6ECE4934 Step 4-7
- 书签F569320A 40
- 书签D54C0547 29
- 书签6A88AB9F 30
- 书签7B08994B 27
- 书签C4BB916B 28
- 书签FEBEA7DB 33
- 书签50277F13 22
- 书签F58CA164 9
- 书签93E516EC 4. From underneath, reassemble the gasket assembly \(#40\), then screw on the lock nut \(#29\). Hand tighten the lock nut \(#29\) lining up one of the screws \(#30\) with the groove in the gasket assembly \(#40\). Do not over tighten. Use a Philips screwdriver to tighten the screws \(#30\) on the lock nut \(#29\). Note: Assemble in the order listed with the rubber washer \(#27\) first. See the diagram for a visual. Hint: Have someone hold the body \(#18\) in place while tightening.
- 书签28BD6EEA 5. Remove the screw from the weight \(#33\). Insert the hose \(#9\) into the groove of the weight \(#33\) at the lowest point on the downward side of the hose \(#9\) and reinstall the screw. Attach the hose \(#9\) to the quick connect assembly \(#22\). The hose \(#9\) is fully connected when you hear a light click or popping sound. Note: Do not remove the reminder tag with the quick connect assembly \(#22\) instructions.
- 书签C7678946 water supplies in a clockwise direction. Tighten the water supply tubes/lines onto the water supply shut offs.Be sure to connect the cold water supply tube/line to the cold water supply valve \(typically on the right\) and the hot water supply tube/line to the hot water supply valve \(typically on the left\). Use a wrench \(as shown\) to tighten the nut. Hold the tubes/lines into a bucket and turn the water supply valves on for one minute. Turn off the water supply valves.
- 书签2C781FE3 6. Apply Teflon tape onto the threads of the faucet
- 书签7A0319AB Screw
- 书签BE0C406A 18
- 书签5FC97FD8 7. Wrap the threads of the waterway \(#20\) with Teflon tape. Slip ½" coupling nuts onto water supply tubes or use flexible stainless steel supply lines \(recommended\) - both are sold separately. Use two wrenches \(as shown\) to keep from twisting the supply tube off of the faucet when tightening the nut.
- 书签82CCCB46 20
- 书签1427DDB4 20
- 书签2CD42B53 Installation Instructions
- 书签AE30A65F 8
- 书签4899C06D 12
- 书签1F727335 34
- 书签63A20FD2 35
- 书签A2B11C54 37
- 书签49FDD8ED 38
- 书签FD51B1DF 39
- 书签99A90ED8 35
- 书签96BD7E1A 39
- 书签EF12A690 35
- 书签97EDDA3E 34
- 书签16257CFD Open the hot and cold shut offs. Check for leaks. If a leak occurs, refer to step 6 or 7. Remove the spray head \(#8\) from the spout \(#12\). Hold the hose \(#9\) in the sink to avoid spraying water out of the sink. Turn on the water and let it run for one minute. This will help clear any debris that may have come loose during installation and prevent the system from becoming clogged. Turn off the water, verify the screen washer \(#41\) is on the hose \(#9\) and screw the spray head \(#8\) onto the hose \(#9\).
- 书签122B3A93 8.
- 书签C585DADE Remove the pump \(#34\) and the nozzle from the soap dispenser assembly. Unscrew the bottle \(#39\), lock nut \(#38\) and large washer \(#37\).
- 书签C64C00CF 9.
- 书签8AB25C67 Verify the small washer \(#36\) is in the soap dispenser base \(#35\). Apply silicone sealant to the bottom of the soap dispenser base \(#35\) and place into the far right hole. From underneath, slide the large washer \(#37\) onto the threads and screw on the lock nut \(#38\) hand tight. Hint: Have someone hold the soap dispenser base \(#35\) in place while tightening.
- 书签D145BF41 10.
- 书签6A64B223 36
- 书签FB4CFA50 From underneath, screw the bottle \(#39\) onto the soap dispenser base \(#35\). Pour the liquid soap or lotion into the bottle \(#39\). To avoid overflow when the pump \(#34\) is inserted, do not overfill.
- 书签724AC74F 11.
- 书签7138E584 Insert the pump \(#34\) into the soap dispenser base \(#35\). Note: The first time the pump \(#34\) is used, it will take several pumps to get the liquid flowing.
- 书签790C47AA 12.
- 书签110B8238 35
- 书签EDF68C88 37
- 书签B8DA5A1C 38
- 书签0B0580FD 36
- 书签0F71CCC9 Step 8-12
- 书签326E7697 41
- 书签F3CA0B7E 9
- 书签555B7F7F Defective switch.
- 书签F622D8DB Contact customer service department for a replacement head.
- 书签A8F80999 The spray head \(#8\) will not switch between spray and stream.
- 书签C9AE1AA8 Revised on 01/04/2021
- 书签044BC997 Troubleshooting
- 书签A8EF554F The lock nut \(#5\) has come loose or the O-ring on the cartridge \(#6\) is dirty or misaligned.
- 书签F8E30D0B Release the pressure in the faucet system. Remove the handle button \(#2\), set screw \(#3\), handle \(#1\), and trim cap \(#4\). If the lock nut \(#5\) is loose tighten it. If the lock nut \(#5\) is tight, remove the lock nut \(#5\) and cartridge \(#6\). Verify the O-ring is clean and in proper alignment on the cartridge \(#6\). If the O-ring is dirty rinse in warm water. Reinstall the O-ring onto the cartridge \(#6\). Reinstall the cartridge \(#6\), lock nut \(#5\), trim cap \(#4\), handle \(#1\), set screw \(#3\) and handle button \(#2\). Turn the water supply valves on.
- 书签36C5EA37 Dirty or damaged cartridge \(#6\).
- 书签8F5EFCBA Release the pressure in the faucet system. Remove the handle button \(#2\), set screw \(#3\), handle \(#1\), trim cap \(#4\), lock nut \(#5\) and cartridge \(#6\). Check the ceramic disk for dirt and damage. If the cartridge \(#6\) is damaged, replace the cartridge \(#6\). If the cartridge \(#6\) is dirty, soak it in warm white vinegar for 4 hours. Every 30 minutes, while the cartridge \(#6\) is completely submerged, turn the stem on and off 10 times. Reinstall the cartridge \(#6\), lock nut \(#5\), trim cap \(#4\), handle \(#1\), set screw \(#3\), and handle button \(#2\). Turn the water supply valves on.
- 书签0C8DADFC Leaks under the handle \(#1\).
- 书签0AA88F7A The water will not shut off completely.
- 书签0609C7D9 The quick connect assembly \(#22\) is loose or misaligned.
- 书签E6643E9C Release the pressure in the faucet system. Release the hose \(#9\) from the quick connect assembly \(#22\). Unscrew the quick connect assembly \(#22\). Add Teflon tape to the threads and reinstall. Connect the hose \(#9\) and turn the water supply valves on. Test for leaks. If the quick connect assembly \(#22\) continues to leak, contact customer service.
- 书签DADD30C9 Leak at the quick connect assembly \(#22\).
- 书签25B6E9A6 The manufacturer warrants that the parts and assemblies of this product will be free from defects in material and workmanship under normal household use for as long as it is owned by the original consumer purchaser. This warranty covers the original purchaser with original receipt only and does not include business, commercial or industrial use of this product. This warranty shall not apply to goods which have been subject to accidents, negligence or improper installation. Our responsibility under this warranty is limited only to the replacement of parts and no other costs. Should a malfunction occur within the time covered by this warranty, replacement parts may be obtained from Customer Service Department 1-800-626-3525 or email warranty@cmiproduct.com. The manufacturer will, at its discretion, provide replacement parts for installation by consumer for any parts that prove defective under normal usage and care with new or equivalent parts.
- 书签663C98F9 If the installation instructions have been followed carefully and the faucet still does not work properly, take these corrective steps. CAUTION: Faucets are under pressure. For safety, before preforming maintenance on the faucet always turn off the water at the water supply valve and turn on the handle\(s\) to release the pressure.
- 页 5
- 书签A9034309 Installation Instructions
- 书签6B78E0B4 8
- 书签8660724C 12
- 书签7980E53B 34
- 书签D3BE8805 35
- 书签A2D0A4F8 37
- 书签F65E88C0 38
- 书签EBDC2A31 39
- 书签C42BA922 35
- 书签C7B0B90B 39
- 书签FE791A30 35
- 书签45A6B9C5 34
- 书签A39F529D Open the hot and cold shut offs. Check for leaks. If a leak occurs, refer to step 6 or 7. Remove the spray head \(#8\) from the spout \(#12\). Hold the hose \(#9\) in the sink to avoid spraying water out of the sink. Turn on the water and let it run for one minute. This will help clear any debris that may have come loose during installation and prevent the system from becoming clogged. Turn off the water, verify the screen washer \(#41\) is on the hose \(#9\) and screw the spray head \(#8\) onto the hose \(#9\).
- 书签3FBC3A8E 8.
- 书签3BCC1F63 Remove the pump \(#34\) and the nozzle from the soap dispenser assembly. Unscrew the bottle \(#39\), lock nut \(#38\) and large washer \(#37\).
- 书签9A712AEA 9.
- 书签CAB2E99C Verify the small washer \(#36\) is in the soap dispenser base \(#35\). Apply silicone sealant to the bottom of the soap dispenser base \(#35\) and place into the far right hole. From underneath, slide the large washer \(#37\) onto the threads and screw on the lock nut \(#38\) hand tight. Hint: Have someone hold the soap dispenser base \(#35\) in place while tightening.
- 书签C13FD917 10.
- 书签F7372C3F 36
- 书签CC972632 From underneath, screw the bottle \(#39\) onto the soap dispenser base \(#35\). Pour the liquid soap or lotion into the bottle \(#39\). To avoid overflow when the pump \(#34\) is inserted, do not overfill.
- 书签89B992EF 11.
- 书签7967156A Insert the pump \(#34\) into the soap dispenser base \(#35\). Note: The first time the pump \(#34\) is used, it will take several pumps to get the liquid flowing.
- 书签301C75AC 12.
- 书签ACA63397 35
- 书签9B0F925C 37
- 书签2483AA59 38
- 书签5414C6F1 36
- 书签B4704599 Step 8-12
- 书签873602DB 41
- 书签AF6B12A8 9
- 页 6
- 书签C4EAFBFA Defective switch.
- 书签34E8EDA5 Contact customer service department for a replacement head.
- 书签9BBC3925 The spray head \(#8\) will not switch between spray and stream.
- 书签B2D723AB Revised on 01/04/2021
- 书签C66246A3 Troubleshooting
- 书签36D5E170 The lock nut \(#5\) has come loose or the O-ring on the cartridge \(#6\) is dirty or misaligned.
- 书签5158B58D Release the pressure in the faucet system. Remove the handle button \(#2\), set screw \(#3\), handle \(#1\), and trim cap \(#4\). If the lock nut \(#5\) is loose tighten it. If the lock nut \(#5\) is tight, remove the lock nut \(#5\) and cartridge \(#6\). Verify the O-ring is clean and in proper alignment on the cartridge \(#6\). If the O-ring is dirty rinse in warm water. Reinstall the O-ring onto the cartridge \(#6\). Reinstall the cartridge \(#6\), lock nut \(#5\), trim cap \(#4\), handle \(#1\), set screw \(#3\) and handle button \(#2\). Turn the water supply valves on.
- 书签05E328EB Dirty or damaged cartridge \(#6\).
- 书签AF7C5633 Release the pressure in the faucet system. Remove the handle button \(#2\), set screw \(#3\), handle \(#1\), trim cap \(#4\), lock nut \(#5\) and cartridge \(#6\). Check the ceramic disk for dirt and damage. If the cartridge \(#6\) is damaged, replace the cartridge \(#6\). If the cartridge \(#6\) is dirty, soak it in warm white vinegar for 4 hours. Every 30 minutes, while the cartridge \(#6\) is completely submerged, turn the stem on and off 10 times. Reinstall the cartridge \(#6\), lock nut \(#5\), trim cap \(#4\), handle \(#1\), set screw \(#3\), and handle button \(#2\). Turn the water supply valves on.
- 书签A3949B75 Leaks under the handle \(#1\).
- 书签4A870299 The water will not shut off completely.
- 书签71B3973F The quick connect assembly \(#22\) is loose or misaligned.
- 书签D1A77708 Release the pressure in the faucet system. Release the hose \(#9\) from the quick connect assembly \(#22\). Unscrew the quick connect assembly \(#22\). Add Teflon tape to the threads and reinstall. Connect the hose \(#9\) and turn the water supply valves on. Test for leaks. If the quick connect assembly \(#22\) continues to leak, contact customer service.
- 书签274E2425 Leak at the quick connect assembly \(#22\).
- 书签44B06E3A The manufacturer warrants that the parts and assemblies of this product will be free from defects in material and workmanship under normal household use for as long as it is owned by the original consumer purchaser. This warranty covers the original purchaser with original receipt only and does not include business, commercial or industrial use of this product. This warranty shall not apply to goods which have been subject to accidents, negligence or improper installation. Our responsibility under this warranty is limited only to the replacement of parts and no other costs. Should a malfunction occur within the time covered by this warranty, replacement parts may be obtained from Customer Service Department 1-800-626-3525 or email warranty@cmiproduct.com. The manufacturer will, at its discretion, provide replacement parts for installation by consumer for any parts that prove defective under normal usage and care with new or equivalent parts.
- 书签9E340783 If the installation instructions have been followed carefully and the faucet still does not work properly, take these corrective steps. CAUTION: Faucets are under pressure. For safety, before preforming maintenance on the faucet always turn off the water at the water supply valve and turn on the handle\(s\) to release the pressure.