Installation Instructions
Table Of Contents
- 页 1
- 页 2
- 页 3
- 书签9A77D69A nipple
- 书签BEAD4591 8-11/16" \(220mm\)
- 书签A16E6F54 4-9/16" \(116mm\)
- 书签4A192335 Min1-5/8"-Max2-1/4" \(40mm-60mm\)
- 书签279BBF86 1/2-14NPT-2A
- 书签2A943A8B 4-1/2-14NPT-2A
- 书签9AD07C12 1-3/8"-1-7/8" \(35mm-47mm\)
- 书签0E9E01E8 Φ6-7/8" \(175mm\)
- 书签39CEC690 Φ5-1/2" \(140mm\)
- 书签9B229304 5/8" \(16mm\)
- 书签54A0FB4F 10-1/2" \(267mm\)
- 书签B95B4A79 5-1/2" \(140mm\)
- 书签16CF887A 5" \(127mm\)
- 书签4590A788 Min 8"-Max 12" \(203mm-305mm\)
- 书签705B55D9 Recommended 74” \(1880mm\) Minimum From Floor To Showerhead, Or Greater As Desired
- 书签E9FED9EB Note: Be sure the valve body is secured to the support cross board for stability.
- 书签36C745AE 1-3/8'' - 1-7/8''
- 书签DBA39CCF 1-3/8'' - 1-7/8''
- 页 4
- 书签3EEE3276 Installation Instructions
- 书签2BFCB33B 5. Turn on hot and cold water supply lines. Turn on the faucet and let the water run from the tub spout for one minute to flush the debris from the line. If there is a leak, refer to correct section and repeat step.
- 书签ACD0CD3B 7. Slide the spout \(#21\) over the nipple. Attach the spout \(#21\) to the nipple with the screw \(#35\), using the Allen wrench \(#27\). See the diagram for visual. Note: The tub spout \(#21\) can be screwed directly onto a threaded nipple. If this option is being used, measure the spout \(#21\) from the threads to the back of the spout \(#21\) to determine the length of nipple needed. Unscrew the plastic core \(#37\). You will not need the plastic core \(#37\), ring \(#36\), and screw \(#35\). Screw the spout \(#21\) directly onto the nipple.
- 书签432A3B57 Note: Ensure the rubber washer \(#26\) is between the shower head \(#24\) and shower arm \(#23\).
- 页 5
- 页 6
- 书签B9D7F42C Revised on 10/16/2020
- 书签BD4940C6 Dirty or pressure locked cartridge \(#11\).
- 书签8A6E06E8 Turn off the water supply. Remove the cartridge \(#11\) and soak for 4 hours. Every 30 minutes while the cartridge \(#11\) is submerged in the vinegar, rotate the stem on and off 10 times. Be sure the pressure balance spool is moving freely \( located at the bottom of the cartridge \(#11\)\). Reinstall cartridge \(#11\).
- 书签8960F679 Lock nut \(#10\) has come loose or o-ring on cartridge \(#11\) is dirty or twisted.
- 书签BEC99952 Rubber valve seat at the base of pressure balance cartridge \(#11\) is dirty or broken.
- 书签44CA051D Tighten the lock nut \(#10\). Clean or replace o-ring on cartridge \(#11\).
- 书签D97266F6 Remove handle and pressure balance cartridge \(#11\) to check the rubber valve seat. Clean or replace it.
- 书签F6A9A69E Troubleshooting