CEILING FAN LIGHT KIT Owner’s Manual Models #20558 If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.
PACKAGE CONTENTS Unpack your light kit and check the contents. You should have the following items: 1 10 5 9 6 Hardware Kit 4 PACKAGE CONTENTS 7 11 Owner’s Manual 3 2 8 1. Canopy 7. Finial (1 + 2 extra) 2. Downrod 8. Fabric Shade 3. Hex Nut 9. Bulbs (x 3) 4. Lock Washer 10. Hardware Kit 5. Light Kit Fitter 11. Owner’s Manual 6. Finial Cap (1 + 2 extra) HARDWARE LIST 12. Wire Connector (x 2) 17. Mounting Bracket 13. Hex Nut 18. Cap Nut (x 2) 14. Lock Washer 19.
SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE BEGINNING TO INSTALL THE LIGHT KIT AND SAVE INSTRUCTIONS. • This fixture is intended for use with an indoor ceiling fan. Not suitable for damp or outdoor locations. • The fan images and instructions in this manual are generic, but in most cases the installation will be easy to follow. If unsure about installation, consult a qualified licensed electrician for proper installation.
ASSEMBLY INSTRUCTIONS - FAN MOUNT 1. Turn OFF the electrical power at the main fuse or circuit breaker. 1 For Ceiling Mount, skip to page 7. A Fitter Plate Switch Housing B Switch Housing Cap 2 Switch Housing A Switch Housing Switch Housing Screw 3 B Switch Housing Cap Note: Save the three switch housing screws for later. 4. Use a screwdriver to push the plug button out of the switch housing (A) or switch housing cap (B). Plug Button B Switch Housing Cap 3.
ASSEMBLY INSTRUCTIONS - FAN MOUNT Shade Support 5 A 5. Install the bulbs in sockets of the light kit fitter. Then, Remove the hex nut and lock washer from the top of the light kit fitter. Then, feed the wires and threaded rod on top of the light kit fitter through the center hole in the shade support. 6. Feed the wires from the light kit fitter through the center hole in the switch housing (A) or switch housing cap (B) and secure by reinstalling the lock washer and hex nut. B 6 7.
ASSEMBLY INSTRUCTIONS - FAN MOUNT Light Kit Fitter Fan Pull Chain 9 Lens Finial Finial Cap 9. Remove the finial cap and finial from the threaded rod at the bottom of the light kit. Then, feed the pull chain from the fan down through the inside of the fabric shade. Feed the pull chains through the appropriate holes in the lens, finial cap and finial. Note: You may substitute one of the extra finial caps and finials if the pre-installed set does not match the metal finish on your fan.
ASSEMBLY INSTRUCTIONS - CEILING MOUNT 1. Turn OFF the electrical power at the main fuse or circuit breaker. 1 2. Install the bulbs in the sockets of the light kit fitter. Light Kit Fitter 2 Bulb Light Kit Fitter 3. Remove the hex nut and lock washer from the top of the light kit fitter. Then, feed the wires and threaded rod on top of the light kit fitter through the center hole in the shade support. Secure the shade support to the light kit fitter by reinstalling the hex nut and lock washer.
ASSEMBLY INSTRUCTIONS - CEILING MOUNT Lock Washer 5. Feed the wires through the downrod and canopy. Secure the downrod and canopy to the IP rod by reinstalling the lock washer and hex nut. Hex Nut Canopy Downrod 5 IP Rod 6. Attach the mounting bracket to the outlet box (not included) using the screws and washers provided with the outlet box. Outlet Box Mounting Bracket Bracket Screw 6 Cap Nut 7. Remove the two cap nuts from the bracket screws.
ASSEMBLY INSTRUCTIONS - CEILING MOUNT 9. Attach the pull chain extensions to the pull chains. 9 Pull Chain Extension 10. Restore the power at the main fuse or circuit breaker. Assembly is complete.
TROUBLESHOOTING If you have difficulty operating your new light kit, or have difficulty with installation, please contact Customer Service : 1-877-459-3267, 9 a.m.- 5 p.m. Central time. WARNING: Ensure the power is turned off to the ceiling fan and light kit before performing any maintenance. PROBLEM SUGGESTED REMEDY Fixture does not light up when installed to fan. 1. Turn on wall switch, and check fuses or circuit breakers. 2.
