Datasheet

ManualsBrandsTRU COMPONENTS ManualsResistorsCarbon film resistor 1 MΩ Axial lead 0207 0.25 W TC-CFR0W4J0105KIT203 100 pc(s)

1. Scope:

This specification for approval relates to Coated Type Kit Resistors (CFR)

2. Type designation:

(Ex.) CR 1/4W J 10

Type Power Rating Resistance Nominal

Tolerance Resistance

3. Ratings:

Ratings shall be shown in the table 1.

Table 1

Type

Rated Power

Max. Working Voltage

Max. Overload Voltage

Dielectric Withstanding Voltage

Rated Ambient Temp.

Operating Temp.Range.

Resistance Tolerance

Resistance Range

3.1 Power rating:

Resistors shall have a power rating based on continuous full load operation at an

ambient temperature of 70 ℃. For temperature in excess of 70 ℃ , the load shall be

derated as shown in the figure 1.

3.2 Voltage rating:

Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate

sine-wave root-mean-square (RMS) alternating-current (AC) continuous working voltage at commercial-

line frequency and waveform curresponding to the power rating , as determined from the

following formula :

RCWV =

√P x R

Were : RCWV = Rated DC or RMS AC continuous working voltage at commercial-line frequency and

waveform (volt)

P = Power Rating (watt)

R = Nominal Resistance (ohm)

250 V

± 5 %

1----10M

500 V

70 ℃

-55℃ --- +155℃

0.25 W at 70℃

The type designation shall be in the following form :

All part numbers in the coding below start with "TC-" and end with "203"

Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau

Datasheet

V1_0717_01_en

Summary of content (10 pages)

PAGE 1
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en 1. Scope: This specification for approval relates to Coated Type Kit Resistors (CFR) 2. Type designation: The type designation shall be in the following form : All part numbers in the coding below start with "TC-" and end with "203" (Ex.) CR 1/4W J 10Ω Type Power Rating Resistance Nominal Tolerance Resistance 3. Ratings: Ratings shall be shown in the table 1. Table 1 CR Type 0.
PAGE 2
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en Coated Type Kit Resistors (CFR) In no case shall the rated DC or RMS AC continuous working voltage be greater than the applicable maximum value. Figure 1. 3.3 Nominal resistance : Effective figures of nominal resistance shall be in accordance with E-24 series, and resistance tolerance shall be shown by table 1. 4. Construction : Name No.
PAGE 3
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en Coated Type Kit Resistors (CFR) 5. Characteristics : Characteristics DC. resistance Test Methods ( JIS C 5201-1 ) Limits Must be within the specified The limit of error of measuring apparatus tolerance. shall not exceed allowable range or 5% of resistance tolerance (Sub-clause 4.
PAGE 4
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en Coated Type Kit Resistors (CFR) 5. Characteristics : Characteristics Temperature coefficient Test Methods ( JIS C 5201-1 ) Limits Resis.Range T.C.R. (PPM/℃) ≦ 10 Ω 0 ～ ±350 11Ω ～ 99K 0 ～ -450 100K ～ 1M 0 ～ -700 1.1M ～ 10M 0 ～ -1500 Natural resistance change per temp. degree centigrade.
PAGE 5
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en Coated Type Kit Resistors (CFR) Characteristics Limits Test Methods ( JIS C 5201-1 ) The area covered with a new , smooth clean , shiny and continuous surface free Solderability 95 % coverage Min. from concentrated pinholes. Test temp. of solder : 245℃ ± 3℃ Dwell time in solder : 2 ~ 3 seconds Soldering temp.
PAGE 6
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en Coated Type Kit Resistors (CFR) Characteristics Test Methods ( JIS C 5201-1 ) Limits Temperature cycling Resistance change rate is ± (1% + 0.05Ω) Max. with no evidence of mechanical damage. Vibration Resistance change rate is ± (1% + 0.05Ω) Max.
PAGE 7
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en Coated Type Kit Resistors (CFR) 6. Dimension : Unit : mm Type Power Rating D (Max.) L (Max.) d ± 0.05 H±3 CR 1/4W 2.5 mm 6.8 mm 0.54 mm 28 mm Painting method: Welding point, terminal and lead wire, is permissible to be exposed without the outer coated cover. The extent should be within 1/2 of the are angle. 7. Marking : 7.
PAGE 8
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en Coated Type Kit Resistors (CFR) 8. Packing specification : 8.1 Taping dimension : Dimensions (mm) Type Style O P L1-L2 T Z R t S CR-25 PT-52 52±1 5±0.3 1 Max. 6±1 1 Max. 0 4 ±1 0.5 Max. 8.2 Bulk in inner box packing ( in plastic Bag ) 100 pcs./polybag 255x0.08x72 (mm) LxHxW Inner Box of Plastic Bag. (3,000 pcs.) Dimension (mm) Type CR-25 Q'ty / Q'ty / Inner Box Bag (pcs.) (pcs.
PAGE 9
Distributed by Conrad Electronic SE • Klaus-Conrad-Str.
PAGE 10
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en Coated Type Kit Resistors (CFR) Environment Related Substance This product complies to EU RoHS directive, EU PAHs directive, EU PFOS directive and Halogen free. Ozone layer depleting substances. Ozone depleting substances are not used in our manufacturing process of this product.