PSCS 10-3,6V EN TRT-BA-PSCS10-3,6V-TC-002-EN ORIGINAL INSTRUCTIONS CORDLESS BATON SCREWDRIVER
Follow the manual Information marked with this symbol indicates that the instructions must be observed. Table of contents Notes regarding the instructions .......................................... 1 Wear safety glasses Information marked with this symbol indicates that you should wear eye protection. Safety ..................................................................................... 1 Information about the device................................................ 6 Transport and storage...........
General Power Tool Safety Warnings – Work area safety • Keep work area clean and well lit. Cluttered or dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
General Power Tool Safety Warnings – Power tool use and care • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. • Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Residual risks Intended use Only use the device PSCS 10-3,6V: • for screwing in and loosening screws, • for drilling in wood, plastic, ceramic and metal, whilst adhering to the technical data. We recommend using the power tool with original Trotec accessories. Improper use The device is not intended for drilling in concrete or natural stone. Personnel qualifications People who use this device must: • have read and understood the instructions, especially the Safety chapter.
Warning Risk of injuries caused by flying parts or bursting tool heads. Warning Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications! Warning The device is not a toy and does not belong in the hands of children. Warning Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.
No. Designation 1 Tool holder with locking mechanism Device description 2 Torque selection The cordless baton screwdriver has an adjustable handle that can be positioned horizontally or vertically to the screw bit. The integrated torque selection, including one drilling setting, allows you to use the optimum power for every application, adapted to the material and screw size. The tool holder with locking mechanism further enables an easy and tool-free exchange of the insertion tools.
Information on noise and vibration: • The vibration level specified in these instructions was determined by means of a measuring method standardized in EN 60745 and can be used for a device comparison. The specified vibration emission value may also be used for a preliminary assessment of the exposure. Technical data Parameter Value Model PSCS 10-3,6V Nominal voltage 3.6 V Idle speed 200 rpm Torque settings 6 +1 Tool holder Hexagon tool holder with locking mechanism Max.
Storage Transport and storage Note If you store or transport the device improperly, the device may be damaged. Note the information regarding transport and storage of the device. Transport For transporting the device, use the transport case included in the scope of delivery in order to protect the device from external influences. Before transporting the device, observe the following: • Switch off the device by setting the switch for clockwise/ counter-clockwise rotation to centre position (lock).
2. Insert the mains plug of the charger (11) into a properly fused mains socket. ð Charging requires approx. 3 hours. Start-up Unpacking the device • Take the transport case out of the packaging. Warning of electrical voltage Electric shock from insufficient insulation. Check the device for damages and proper functioning before each use. If you notice damages, no longer use the device.
Changing tools The device is equipped with a tool holder with locking mechanism for hexagon (drill) bits. Please proceed as follows to remove or insert tools: 1. Set the switch for clockwise/counter-clockwise rotation (5) to centre position (lock). 2. Pull the locking mechanism at the tool holder (1) back and hold it in place. 3. If necessary, take the (drill) bit out of the tool holder (1). Torque selection / drilling setting Using the torque selection, you can choose the desired, optimal torque setting.
Operation Selecting the rotational direction Tips and notes on handling the cordless screwdriver General information: • Check the tool in the bit holder for correct fit before every application. • The centre position of the clockwise / counter-clockwise rotation switch (lock) is suited for work breaks or (drill) bit exchange. Screws: • In case of soft wood, screws can be screwed in without pre-drilling. • In case of hard wood or large screws, it is recommended to use a drill for pre-drilling.
Handle position The handle position can be adjusted to either vertical or horizontal in order to reach poorly accessible locations more easily. 1. Set the switch for clockwise/counter-clockwise rotation (5) to centre position (lock). 2. Press and hold the handle position switch (4). 4 12 Switching the device on and off 1. Check whether the tool and the selected torque setting are suitable for the intended application. 2. Check whether the workpiece is secured and the worktop prepared correspondingly. 3.
Available accessories Warning Only use accessories and additional equipment specified in the operating manual. Using insertion tools or accessories other than those specified in the operating manual may cause a risk of injury. Accessories Article number Screw bit set, 32-piece 6,200,001,001 Info Wait for at least 10 minutes before switching the device back on. Errors and faults The device has been checked for proper functioning several times during production.
Maintenance Disassembly Activities required before starting maintenance Battery removal and disposal 1. Completely discharge the battery by letting the device run until the motor stops. 2. Loosen the 5 screws at the handle (6). 3. Open the housing. 4. Version A (without plug connection): Hold onto the battery (15) and disconnect the wiring by means of a wire cutter. Insulate the severed wire ends of the battery with tape to prevent a short circuit.
Disposal Declaration of conformity The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment must not be disposed of with the household waste at the end of its life. You will find collection points for free return of waste electrical and electronic equipment in your vicinity. The addresses can be obtained from your municipality or local administration. For further return options provided by us please refer to our website www.trotec24.com.
Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.
