Instruction Manual

ManualsBrandsTrimec ManualsPower ToolsES9000 Pre-Load Electric strike

ES9000 SERIES ELECTRIC STRIKE

INSTALLATION INSTRUCTIONS

CHANGING MODE OF LOCK OPERATION

Power to Lock (PTL) to Power to Open (PTO) conversion.

Loosen mode change screw two turns with the supplied

2mm hex key.

Factory default setting is Power to Lock (PTL)

Move to required position as shown:

Power to Open Fig. A

Power to Lock Fig. B

Retighten mode change screw firmly.

POSITIONING OF STRIKE

Peel backing off adhesive template and centrally locate in the

marked position, lining up both the mark for the door latch front

face (Line 1) and the centre mark of the latch (Line 2).

For a metal door drill two Ø5mm holes (A) 22mm above and

below the ‘x’ mark on the template, for a timber door drill

two Ø3mm holes (B).

Ensure secondary bolt is not within strike cavity.

Hole 'B'

Metal Door Frame Timber Door Frame

Strike

cavity

22mm

Hole 'A'

Line 1

Line 2

A - Power to Open

(Fail-Secure)

Configuration

B - Power to Lock

(Fail-Safe)

Configuration

ICK-

TP0

Depth of lIp cutout will vary due

outline

ibe

Crack and peel back to stIck

template to face of door frame

TEMP

Front face of lock latch

ES200-ES2000

ES9000

to width of door frame and

mounting technIque.

ICK-

TP0

Depth of lIp cutout will vary due

outline

ibe

Crack and peel back to stIck

template to face of door frame

TEMP

Front face of lock latch

ES200-ES2000

ES9000

to width of door frame and

mounting technIque.

Part No. ES9000-121

30621 1008

Using the template as a guide, mortice out the door frame to the

required size.

Countersink holes in metal frame to accept screws.

For wider framed doors an Extension Lip may be required. Refer

to over leaf for sizes and part numbers.

MORTICING REBATE

24mm

To enable the Electric strike to be located in the door frame, first

mark the position of the Door Latch front face on the door frame

with the door in the closed position, ('X ' mm).

Mark where centre of latch meets door frame:

- For new installations, mark frame where front of latch touches

the door frame at the midpoint of the latch bolt.

- For retrofit installations, remove existing strike plate and ensure

that latch fits into and is centred in existing hole.

Frame

Door

Latch

Mark Door latch

front face on frame

(Line 1).

MARKING OF STRIKE POSITION

'X ' mm

Mark centre of Door

latch on frame

(Line 2).

Line 1

Line 2

Summary of content (2 pages)

PAGE 1
R ES9000 SERIES ELECTRIC STRIKE MARKING OF STRIKE POSITION 1 POSITIONING OF STRIKE 2 'X ' mm Scr outliibe ne LATE EMP Line Crack and peel back to stIck template to face of door frame 22mm 2 Strike cavity Front face of lock latch ES200-ES2000 ES9000 T TP0 - ON 00 ES200-ES2000 ES9000 Latch Front face of lock latch 2 Door Frame STIC K Crack and peel back to stIck template to face of door frame Line T TP0 - ON 00 Depth of lIp cutout will vary due to width of door frame and mounting te
PAGE 2
ELECTRICAL SPECIFICATION CAUTION! Incorrect supply voltage may cause damage not covered by warranty. Solenoid Monitor Wiring: Please check supply voltage with a suitable meter to ensure it is within 10-30V DC. Unpowered Current required is 250mA @12V DC to 130mA @ 24V DC DO NOT OIL OR LUBRICATE. 9000 Series Microswitch Monitoring The 9000 Series Electric Strike has back EMF protection built into the product. No external protection diode is required. N.O. (Normally Open) Grey Common Orange N.C.