Installation Guide

ManualsBrandsTransolid ManualsBathroom Vanity TopsG2519-E3-E-B-1

Vanity Top Installation Instructions

Natural Granite, Marble and Engineered Quartz

Thank you for purchasing a Transolid

Vanity Top. Please read the instructions carefully

prior to installing the top. These are basic instructions for installation in a step-by-step

sequence that will work in most types of installations. If you have an installation that is

not covered here, please contact Transolid for additional information.

Tools and Supplies Needed for Installation

• Silicone Caulk • Shims / Blocks

1. Unpack the vanity top and inspect it for any damage. Report any

damage to your place of purchase.

2. Make sure the top sits securely on the cabinet. Transolid recom-

mends using shims in areas where there is not a solid point of

contact or where the top is not level on the cabinet.

3. Install the faucet and the drain assembly according to the

manufacturer’s instructions.

4. Wipe off the top of the vanity cabinet with a damp cloth to remove

any dirt. Apply a generous (1/2”) bead of silicone around the top

edges of the vanity cabinet. See Figure 1.

5. Carefully lower the top onto the vanity cabinet, making sure

that the shims stay in place. See Figure 2.

6. Attach the drain pipe to the drain assembly. Attach the water

supply lines to the faucet.

7. If back splash is to be installed, do so at the this time. Test t the

back splash to determine proper t, and which side will face out

and which side will face the wall.

8. Wipe the bottom of the back splash and the top of the vanity with

a damp cloth to remove any dust or dirt.

9. Apply a thin (1/4”) bead of silicone along the bottom edge of the

back splash and several thin beads along the back (wall) side of the

splash. Set the back splash into place.

10. If side splashes are to be installed, follow steps 7-9.

11. Apply a thin bead of caulk around all of the joints, such as the

one between the top of the back splash and the wall, the side

splash and the wall, the vanity top and the back splash, and the

vanity top and the side splash. See Figure 3.

Transolid, Div. • 400 Dietz Road • Warren, OH 44483 • (800) 766-2452 • www.transolid.com

Summary of content (4 pages)

PAGE 1
Vanity Top Installation Instructions Natural Granite, Marble and Engineered Quartz Thank you for purchasing a Transolid® Vanity Top. Please read the instructions carefully prior to installing the top. These are basic instructions for installation in a step-by-step sequence that will work in most types of installations. If you have an installation that is not covered here, please contact Transolid for additional information. Tools and Supplies Needed for Installation • Silicone Caulk • Shims / Blocks 1.
PAGE 2
Instrucciones para instalar una cubierta de lavabo de las líneas cuarzo procesado, granito y marmol natural Gracias por comprar una cubierta de lavabo Transolid. Por favor, lea cuidadosamente las instrucciones antes de instalar la cubierta. Estas son las instrucciones básicas para su instalación en una secuencia paso a paso que funcionará en la mayoría de los tipos de instalaciones.
PAGE 3
Faucet Hole Drilling For Vanity Tops With Faucet Dimples Tools Required: - Pencil - Drill - 1/4” Pilot Drill Bit - Hole Saw - 80-120 Grit Sandpaper Please read all instructions before beginning installation 1. Place the vanity top (ITB), upside down, on sturdy supports. 2. Examine the faucet you intend to install and read through any instructions that came with it. Note the size of hole(s) that will be required. 3. Faucet hole dimple marks are located on the underside of the vanity top.
PAGE 4
10-Year Limited Warranty TRANSOLID, Div. expressly warrants its manufactured solid surface products (not to include Décor vanity tops which are covered under a separate warranty), quartz and granite vanity tops to be free of defects in material and workmanship, subject to the limitations set forth in this Limited Warranty.