Business Networking Solution Installation Guide Gigabit Unmanaged Switch TL-SG1008/TL-SG1008PE TL-SG1016/TL-SG1016D TL-SG1024/TL-SG1024D TL-SG1048
Related Document This Installation Guide is also available in PDF on our website. To obtain the latest documentation and product information, please visit the official website: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during the installation. This Installation Guide is structured as follows: Chapter 1 Introduction.
Contents Chapter 1 Introduction———————————— 01 1.1 1.2 1.3 Product Overview............................................................01 Features...............................................................................01 Appearance........................................................................02 Chapter 2 Installation———————————— 09 2.1 Package Contents...........................................................09 2.3 Installation Tools.................................................
Gigabit Unmanaged Switch Chapter 1 Introduction 1.1 Product Overview The Gigabit Unmanaged Switch provides you with a high-performance, low-cost, easyto-use, seamless and standard upgrade to boost your old network to 1000Mbps. By increasing the speed of your network server and backbone connections, the Gigabit Unmanaged Switch makes Gigabit a reality. Power users in the home, office, workgroup, or creative production environment can now move large, bandwidth-intensive files faster.
Gigabit Unmanaged Switch ■■ ■■ ■■ TL-SG1024/TL-SG1024D/TL-SG1016/TL-SG1016D/TL-SG1008 supports IEEE802.3x flow control for full-duplex mode and backpressure for half-duplex transfer mode TL-SG1008 supports IEEE802.
Gigabit Unmanaged Switch LEDs LED Status Indication Off The switch is powered off or power supply is abnormal. On Power Link/Act On The switch is powered on. Green Yellow Flashing Off The corresponding port is running at 1000Mbps. The corresponding port is running at 10/100Mbps. The corresponding port is transmitting or receiving data. There is no device linked to the corresponding port.
Gigabit Unmanaged Switch The front panel of TL-SG1016D is shown as the following figure. Figure 1-5 Front Panel of TL-SG1016D LEDs 10/100/1000Mbps RJ45 Port The front panel of TL-SG1008 is shown as the following figure. Figure 1-6 Front Panel of TL-SG1008 TL-SG1008 Link Act 8-Port Gigabit Switch Power 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 8 1000Mbps LEDs 10/100/1000Mbps RJ45 Port LEDs LED Power Link/Act Status Indication Off The switch is powered off or power supply is abnormal.
Gigabit Unmanaged Switch The front panel of TL-SG1008PE is shown as the following figure. Figure 1-7 Front Panel of TL-SG1008PE LEDs 10/100/1000Mbps RJ45 Port and PoE Port LEDs LED Status Indication Power Flashing (green) Power supply is abnormal. On (green) Off On (green) Link/Act Flashing (green) Off On (red) PoE MAX Flashing (red) Off 1000Mbps On (green) Off On (green) PoE Status Flashing (green) Off The switch is powered on. The switch is powered off.
Gigabit Unmanaged Switch The 8 ports also support PoE function which integrates power and data onto one Ethernet cable. Once the device you connect to the switch is identified, the switch will supply power through the PoE port, and then you can use it as a 10/100/1000Mbps Auto-Negotiation RJ45 Ethernet port. The working status can be indicated by the PoE MAX LED and PoE Status LEDs on the front panel. Note: Make sure the PDs you connected to the switch are compliant with IEEE802.3af/IEEE802.3at standard.
Gigabit Unmanaged Switch The rear panel of TL-SG1016 is shown as the following figure. Figure 1-10 Rear Panel of TL-SG1016 Power Grounding Socket Terminal The rear panel of TL-SG1024D is shown as the following figure. Figure 1-11 Rear Panel of TL-SG1024D Grounding Terminal Power Socket The rear panel of TL-SG1016D is shown as the following figure. Figure 1-12 Rear Panel of TL-SG1016D Grounding Power Terminal Socket The rear panel of TL-SG1008 is shown as the following figure.
Gigabit Unmanaged Switch The rear panel of TL-SG1008PE is shown as the following figure. Figure 1-14 Rear Panel of TL-SG1008PE Power Socket Grounding Terminal Power Socket Connect the female connector of the power cord here, and the male connector to the AC (Alternating Current) power outlet. Please make sure the voltage of the power supply meets the requirement of the input voltage. Grounding Terminal The switch already comes with lightning protection mechanism.
Gigabit Unmanaged Switch Chapter 2 Installation 2.1 Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord Two mounting brackets and the fittings This Installation Guide Business Networking Solution Installation Guide 2.2 Safety Precautions To avoid any device damage and bodily injury caused by improper use, please observe the following rules.
Gigabit Unmanaged Switch ■■ Site Requirements Temperature/Humidity 40℃ 0℃ Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table.
Gigabit Unmanaged Switch ■■ Use electromagnetic shielding when necessary. Lightening Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. ■■ Ensure the rack and device are well earthed. ■■ Make sure the power socket has a good contact with the ground.
Gigabit Unmanaged Switch Note: These tools are not provided with our product. If needed, please self purchase them. 2.4 Product Installation ■■ Desktop Installation To install the device on the desktop, please follow the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. Remove the adhesive backing papers from the rubber feet. 3.
Gigabit Unmanaged Switch 3. After the brackets are attached to the device, use suitable screws (not provided) to secure the brackets to the rack, as illustrated in the following figure. Rack Figure 2-3 Rack Installation Caution: Please set 5 to 10cm gaps around the device for air circulation. Please avoid any heavy thing placed on the device. Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation.
Gigabit Unmanaged Switch Chapter 3 Lightning Protection 3.1 Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors, please use a signal lightning arrester.
Gigabit Unmanaged Switch ■■ Requirements for Cabling Indoors When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. ■■ ■■ The main cable should be paved in the metal raceway of the access shaft. When cabling, keep the loop area formed by the cable itself as small as possible. Requirements for the distance between Ethernet cable and other pipelines are shown in the table.
Gigabit Unmanaged Switch Cable 2 to 5kVA powerline >5kVA powerline Pave Way Parallel cabling 300 The both are in the grounded metal raceway or metal pipe 80 One is in the grounded metal raceway or metal pipe 150 Parallel cabling 600 The both are in the grounded metal raceway or metal pipe 150 One is in the grounded metal raceway or metal pipe Device Min Distance (m) Transformer room 2.00 Switch case Elevator tower Air-conditioner room 3.2 Min Parallel Length (mm) 300 1.00 2.00 2.
Gigabit Unmanaged Switch Figure 3-1 Connecting to the Ground via Power Supply Switch (Rear Panel) AC Power Cord (with PE cable) Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above.
Gigabit Unmanaged Switch Equipotential Bonding Equipotential Bonding is the practice of intentionally electrically connecting all earthed systems to the same grounding grid or connecting the grounding grids of all the earthed systems together through the ground or overground metal so as to create an earthed equipotential zone.
Gigabit Unmanaged Switch Signal lightning arrester is used to protect RJ45 ports of the device from lightning. When cabling outdoors, please install a signal lightning arrester before connecting the cable to the device. When purchasing or using a signal lightning arrester, please observe the following rules: ■■ ■■ The port rate of the signal lightning arrester should match the rate of the desired port on the device. If it is not matched, this signal lighting arrester will not work.
Gigabit Unmanaged Switch Chapter 4 Connection 4.1 Ethernet Port Connect a Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. RJ45 Port RJ45 Cable Figure 4-1 4.2 Connecting the RJ45 Port Verify Installation After completing the installation, please verify the following items: ■■ 4.3 There are 5 to 10cm of clearance around the sides of the device for ventilation and the air flow is adequate.
Gigabit Unmanaged Switch Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. 4.4 Initialization For TL-SG1048/TL-SG1024/TL-SG1024D/TL-SG1016/TL-SG1016D/TL-SG1008: After the device is powered on, it begins the Power-On Self-Test. A series of tests run automatically to ensure the device functions properly.
Gigabit Unmanaged Switch Appendix A Troubleshooting Q1. Why is the Power LED not lit? The Power LED should be lit up when the power system works normally. If the Power LED worked abnormally, please try the following: 1. 2. Make sure that the power cable is connected properly, and the power contact is normal. Make sure the voltage of the power supply meets the requirement of the input voltage of the switch. Q2.
Gigabit Unmanaged Switch Appendix B Specifications Item Content IEEE802.3i, IEEE802.3u, IEEE802.3ab Standards IEEE802.3x (except TL-SG1048) IEEE802.1p (for TL-SG1008PE/TL-SG1008) IEEE802.3af (for TL-SG1008PE), IEEE802.3at (for TL-SG1008PE) 10Base-T UTP/STP of Cat. 3 or above(maximum 100m) Transmission Medium 100Base-TX 2-pair UTP/STP of Cat. 5 or above (maximum 100m) Safety & Emissions FCC, CE Protocol 1000Base-T 4-pair UTP/STP of Cat.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
BSMI Notice 安全諮詢及注意事項 • 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 • 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 • 注意防潮，請勿將水或其他液體潑灑到本產品上。 • 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 • 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 • 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 • 此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某 些適當的對策。 Industry Canada Statement CAN ICES-3 (A)/NMB-3(A) Explanation of the symbols on the product label Symbol Explanation AC voltage Indoor use only RECYCLING This product bears the selective sorting symbol for
For technical support and other information, please visit http://www.tp-link.com/support, or simply scan the QR code. © 2017 TP-Link 7106507234 REV12.0.
