Enterprise Networking Solution Installation Guide Gigabit Unmanaged Switch TL-SG1048/TL-SG1024 TL-SG1024D/TL-SG1016 TL-SG1016D/TL-SG1008
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.
Related Document This Installation Guide is also available in PDF on our website. To obtain the latest documentation and product information, please visit the official website: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during installation. This Installation Guide is structured as follows: Chapter 1 Introduction.
Contents Chapter 1 Introduction ——————————— 01 1.1 Product Overview ...................................................................01 1.2 Features ......................................................................................01 1.3 Appearance ...............................................................................02 Chapter 2 Installation ———————————— 05 2.1 Package Contents ...................................................................05 2.2 Safety Precautions ........
Gigabit Unmanaged Switch CCCCCCCCCC Introduction 1111 Product Overview The Gigabit Unmanaged Switch provides you with a high-performance, low-cost, easyto-use, seamless and standard upgrade to boost your old network to 1000Mbps. Increase the speed of your network server and backbone connections, making Gigabit a reality. Power users in the home, office, workgroup, or creative production environment can now move large, bandwidth-intensive files faster.
Gigabit Unmanaged Switch 1111 Appearance ■■ Front Panel The front panel of TL-SG1048 is shown as the following figure. LEDs 10/100/1000Mbps RJ45 Port FFFFFFFFFFF Front Panel of TL-SG1048 The front panel of TL-SG1024 is shown as the following figure. LEDs 10/100/1000Mbps RJ45 Port FFFFFFFFFFF Front Panel of TL-SG1024 The front panel of TL-SG1024D is shown as the following figure.
Gigabit Unmanaged Switch The front panel of TL-SG1008 is shown as the following figure.
Gigabit Unmanaged Switch Power Socket Grounding Terminal FFFFFFFFFFF Rear Panel of TL-SG1024/TL-SG1016 The rear panel of TL-SG1024D/TL-SG1016D is shown as the following figure. Grounding Terminal Power Socket FFFFFFFFFFF Rear Panel of TL-SG1024D/TL-SG1016D The rear panel of TL-SG1008 is shown as the following figure.
Gigabit Unmanaged Switch CCCCCCCCCC Installation 2222 Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord This Installation Guide Two mounting brackets and the fittings 2222 Safety Precautions To avoid any device damage and bodily injury caused by improper use, please observe the following rules. ■■ Safety Precautions ■■ Keep the power off during the installation.
TL-SL3428 L2 Lite Managed Switch Gigabit Unmanaged Switch ■■ Site Requirements Temperature/Humidity ȭ ȭ Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device.
Gigabit Unmanaged Switch Lightening Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. ■■ Ensure the rack and device are well earthed. ■■ Make sure the power socket has a good contact with the ground.
Gigabit Unmanaged Switch 2222 Product Installation ■■ Desktop Installation To install the device on the desktop, please follow the steps: 111Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 222Remove the adhesive backing papers from the rubber feet. 333Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device.
Gigabit Unmanaged Switch Rack FFFFFFFFFFF Rack Installation Caution: Please set 5~10cm gaps around the device for air circulation. Please avoid any heavy thing placed on the device. Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation.
Gigabit Unmanaged Switch CCCCCCCCCC Lightning Protection 3333 Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors, please use a signal lightning arrester.
Gigabit Unmanaged Switch ■■ Requirements for Cabling Indoors When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. ■■ ■■ The main cable should be paved in the metal raceway of the access shaft. When cabling, keep the loop area formed by the cable itself as small as possible. Requirements for the distance between Ethernet cable and other pipelines are shown in the table.
Gigabit Unmanaged Switch Cable 2~5kVA powerline >5kVA powerline Pave Way Min Parallel Length (mm1 Parallel cabling 300 One is in the grounded metal raceway or metal pipe 150 The both are in the grounded metal raceway or metal pipe 80 Parallel cabling 600 One is in the grounded metal raceway or metal pipe 300 The both are in the grounded metal raceway or metal pipe 150 Device Min Distance (m1 Switch case 1.00 Transformer room 2.00 Elevator tower 2.00 Air-conditioner room 2.
Gigabit Unmanaged Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. ■■ Connecting to the Ground via the Power Supply If the device is installed in the normal environment, the device can be grounded via the PE (Protecting Earth) cable of the AC power supply as shown in the following figure. FFFFFFFFFFF Connecting to the Ground Note: The figure is to illustrate the application and principle.
Gigabit Unmanaged Switch Grounding Terminal Equipotential Bonding Cable Ground Cable Grounding Bar FFFFFFFFFFF Equipotential Bonding When equipotential bonding, please note that the cable should be copper wrapped 2 Kelly with its area being 6mm at least. The shorter cable the better, and use a grounding bar to establish an equipotential bonding point. Note: The equipotential bonding cable and ground cable are not provided with our product. If needed, please self purchase it.
Gigabit Unmanaged Switch Signal lightning arrester is used to protect RJ45 ports of the device from lightning. When cabling outdoors, please install a signal lightning arrester before connecting the cable to the device. When purchasing or using a signal lightning arrester, please observe the following rules: ■■ ■■ The port rate of the signal lightning arrester should match the rate of the desired port on the device. If it is not matched, this signal lighting arrester will not work.
Gigabit Unmanaged Switch CCCCCCCCCC Connection 4444 Ethernet Port Connect a Ethernet port of the Switch to the computer by RJ45 cable as the following figure shown. RJ45 Port RJ45 Cable FFFFFFFFFFF Connecting the RJ45 Port 4444 Verify Installation After completing the installation, please verify the following items: ■■ There are 5~10cm of clearance around the sides of the device for ventilation and the air flow is adequate.
Gigabit Unmanaged Switch Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. 4444 Initialization After the device is powered on, it begins the Power-On Self-Test. A series of tests run automatically to ensure the device functions properly.
Gigabit Unmanaged Switch Appendix A Troubleshooting QQQQ The Power LED is not lit The Power LED should be lit up when the power system works normally. If the Power LED worked abnormally, please check as follows: 111 Make sure that the power cable is connected properly, and the power contact is normal. 222 Make sure the voltage of the power supply meets the requirement of the input voltage of the Switch.
Gigabit Unmanaged Switch Appendix B Specifications Item Content IEEE 802.3 10Base-T Standards IEEE 802.3u 100Base-TX IEEE 802.3ab 1000Base-T 10Base-T: UTP/STP of Cat. 3 or above(maximum 100m1 Transmission Medium 100Base-TX: 2-pair UTP/STP of Cat. 5 or above(maximum 100m1 1000Base-T: 4-pair UTP/STP of Cat.
Gigabit Unmanaged Switch Appendix C Technical Support ■■ ■■ ■■ For more help, please go to: www.tp-link.com/support/faq.asp To download the latest Firmware, Driver, Utility and User Guide, please go to: www.tp-link.com/support/download.asp For all other technical support, please contact us by using the following details: Global Tel: +86 F55 26504400 E-mail: support@tp-link.com Service time: 24hrs, F days a week Singapore Tel: +65 628404F3 E-mail: support.sg@tp-link.
Gigabit Unmanaged Switch 21 Russian Federation Tel: 8 (4F51 223-55-60 8 (8001 250-55-60 (toll-free call from any RF region1 E-mail: support.ru@tp-link.com Service time: From 10:00 to 18:00 (Moscow time1 *Except weekends and holidays in Russian Federation Brazilian(Portuguese Service1 Toll Free: 0800-FF0-433F E-mail: suporte.br@tp-link.com Service time: Monday to Saturday 08:00 AM to 08:00 PM Ukrainian Tel: +380 (441 5F0-51-14 E-mail: support.ua@tp-link.
Website: http://www.tp-link.com E-mail: support@tp-link.com 7106503774 Rev: 3.1.