OWNER’S MANUAL LCD Monitor P32LSA 1
Contents Safety Instructions-------------------------------------------------------- 3 Notes and Cautions for Use-------------------------------------------- 10 On usage------------------------------------------------------------------------- 10 On disposal or handing over to a new owner -------------------------- 10 Exemptions---------------------------------------------------------------------- 10 Features----------------------------------------------------------------------- 11 Names and Functions of Co
Safety Instructions Before using the unit, please read this manual thoroughly to help protect against damage your own and other people’s property your property from potential damage and ensure your own and other people personal safety. Be sure to observe the following instructions with understanding meaning of signs and figures below. Meaning of Signs Sign Meaning of Sign Disregard may cause death or serious injury*1. Disregard may cause injury*2 or material damage*3.
If water is spilled or objects are dropped inside the unit, remove the power plug from the outlet immediately. If the unit is still used in this condition, it may cause a fire or an electric shock. Contact your dealer for inspection. If the unit is dropped or the cabinet is damaged, remove the power plug from the outlet immediately. If the unit is still used in this condition, it may cause a fire or an electric shock. Contact your dealer for inspection.
Do not place the unit in an unstable location, such as a shaky table or incline. The unit may fall down and cause injury or damage. Install the unit on a horizontal, stable surface. Do not place the unit in a location subject to vibration. The unit may fall down because of the vibration and may cause an injury. Insert the power plug fully into a 100-240V AC outlet. • If you use an outlet other than 100 240 V AC, it may cause fire or electric shock. • Improper insertion of the plug may cause heat and fire.
Follow these precautions for the power cord and lug. Do not damage, modify such as by extending, or heat (such as by pressing near heating equipment). Do not pull, place heavy objects or pinch. Do not bend, twist or bunch up. Fire or electric shock may result. Do not insert objects inside the unit. If metallic materials or combustibles such as paper get inside the unit from ventilation holes and other places, it may cause a fire or an electric shock.
Take measures to prevent the unit from falling down. If not, the unit may fall down and cause injury. Do not block the ventilation holes on the unit. The inside of the unit will overheat if the ventilation holes are sealed, which may result in a fire. • When installing the unit near a wall, keep the unit at least 10 cm from the wall. • Do not place the unit in a closet or bookshelf where ventilation is poor. • Do not spread a newspaper, tablecloth or curtain over the unit.
Do not climb or stand on the unit. It may drop, fall down, break or cause an injury. If the unit will not be used for a long period of time, remove the power plug from the wall outlet for safety. If not, in the case of malfunction, it may cause fire. Precautions for the remote control batteries: Only use the specified battery type. Be sure to insert batteries by matching the + and –. Do not recharge, heat, disassemble, short or throw batteries into a fire.
Cleaning Remove the power plug before cleaning. If not, it may cause electric shock. Consult your dealer for internal cleaning once a year. If you allow dust to accumulate on the unit, it may cause fire or malfunction when you operate it. Cleaning is effective especially before the rainy season when humidity is high. Refer to your dealer about the service charge for internal cleaning.
Notes and Cautions for Use On usage • Some parts of the body are hot during operation. Please be careful. • In case of moving long-distance, wrap the unit with blanket to avoid damages. Be careful not to bump the unit. • Do not spray on the unit volatile liquid like insecticide. Do not expose long time to rubber or vinyl. It will damage the coating. On disposal or handing over to a new owner • It is recommended to initialize the unit by resetting “PICTURE” and “SETUP” menu.
Features High-resolution HD panel You can enjoy extreme fine pictures with a big flat LCD monitor panel of 3,150,000 pixel. MVA system less-reflection black TFT LCD panel MVA system and Black TFT LCD panel offer bright and wide images with clear contrast. Even placed near the window, the unit shows bright and clear images with little reflection. The viewing angles of the monitor are as wide as 170° both horizontally and vertically, enough to enjoy clear images at any view angle.
Names and Functions of Controls Front • Power standby / on indicator -Power ON-Stand by Indicator • Remote sensor • Light sensor -Remote Control Receiver -Light sensor Side Controls Power Enter Z/＋ Y/－ ▽ △ Menu/ Exit (standby / on) (activate selection) (scroll right for Menu items / volume increase) (scroll left for Menu items / volume decrease) (scroll down for Menu items) (scroll up for Menu items) (OSD control Menu button / Access Main / Sub-menu / Quick Menu Selection) 12
Back AC power cord inlet Main power switch 13
Names and Functions of Controls (Option) Power on / Power off OSD control Menu button / Access Main / sub-menu / Quick Menu Selection Menu Left Menu Right Menu Up Menu Down Activate selection One level up Adjust clock, phase, H position and V position Automatically Picture in picture Input source selection PIP picture switch 14
Battery Installation (Option) (1) (2) (3) To replace batteries inside 1) Push down a little as (1) in the picture and pull the back cover 2) Replace with the new batteries as (2), 1 piece Lithium battery (CR2032) make sure the polarity of batteries are correct. 3) Place back cover and slide it is as (3) in the picture. 4) Used batteries need to follow the city rule to discard.
Supplied Accessories Please check all are supplied. Power Cord x 1 (1.
Connection VIDEO SYSTEM INPUT You can select VIDEO input from 3 terminals below; Terminal Type Suitable signals VIDEO-IN RCA NTSC/PAL S-VIDEO S-Video Mini Din 4pin NTSC/PAL YUV (Y Pb/Cb Pr/Cr) Component Mini Din 8 pin NTSC/PAL • Suitable signal is automatically selected.
Connecting the Power Cord Caution: Please turn off the main power switch before connecting. [Back] To unit inlet AC100~240V Wall socket Power cord (1.
Installation Wall hanging accessory is available when you hang the monitor on the wall. Please follow the process mentioned on page 20-22. When you install the monitor on the ceiling or on the floor, please follow the process on page 23. To a service technician For safety, make sure the place has enough strength to hold the whole weight of the monitor and the frames (*1). If necessary, reinforce the place before installation. At least two people are needed for installation.
How to install the monitor on the wall In case of using option bracket (FPT-WA5) 1. Remove the stand of the LCD monitor To avoid damage, spread blanket on the table to put the LCD monitor on. To remove the stand of the LCD monitor, put the LCD monitor on the edge of the table, and remove the screws on the stand. Described below is one example of how to install the unit on the wall.
5. Using Supplied screws, fix the frame on the LCD monitor To avoid damaging, spread blanket on the flat space, and place the LCD monitor with its panel down. Refer to the illustration, and mount the frame on the LCD monitor with four M4 screws. 6. Wire before hanging on the wall On wiring, refer to page 17 – 18. Pay attention to the positions of auxiliary equipment or bracket on the wall, when you decide the route to wire.
7. Mount the LCD monitor on the bracket *: When mounting, at least two people are needed. Raise the LCD monitor, and insert the projection of the bracket. Hold the lower part of the LCD monitor and raise a little, push into the lower part of the bracket.
How to install the LCD monitor on the floor 1. Remove the stand of the LCD monitor To avoid damage, spread blanket on the table to put the LCD monitor on. To remove the stand of the LCD monitor, put the LCD monitor on the edge of the table, and remove the screws on the stand. 2. Floor installation brace for LCD monitor The floor installation brace will be manufactured according to the installation. Before the installation work, please consult your dealer for the floor installation brace. 3.
Dimension Front 24
Back 25
Power On/Off Before turn on, wire all the cable connecting to auxiliary equipment, external speakers, power cord, etc. There are two controls for power, Main power switch and POWER (standby / on) button. Main power switch Bottom Front To unit inlet AC100~240V wall socket Power cord Main power switch To wall outlet ground Mode LED indicator Standby Orange Power on Green If Main power switch is not On, you cannot turn on the unit by the POWER (Standby / On) button.
Menu Function Display Menu, you can adjust pictures and sound or set various functions with the buttons on the remote control. The following are summary of Menu Function. For details, please see to refer pages. Function of each button Side of the unit Side of the unit: No. Remote control (option) Remote control Descriptions No.
Menu display chart MAIN MENU Brightness ．．．．．．．．．．．． （－ , ＋） DISPLAY (Main) Contrast ．．．．．．．．．．．． （－ , ＋） Hue ．．．．．．．．．．．． （－ , ＋） Saturation ．．．．．．．．．．．． （－ , ＋） Flash-Tone ．．．．．．．． （Off,Weak,Soft,Strong） Black Level ．．．．．．．．．．．． （－ , ＋） POSITION Zoom ．．．．．．．．．．．． （In , Out） Zoom Horizontal Pan Zoom Vertical Pan Vertical ．．．．．．． （Left,Right） ．．．．．．．． （Down,Up） ．．．．．．．．．．．． （－ , ＋） Horizontal ．．．．．．．．．．．． （－ , ＋） PIP CONTROL PIP Mode ．．．．．．．．．． （Off,Single,PAP） PIP Size ．．．．．．．．． （Small,Me
Factory default setting Item Default Power switch Off Brightness 80 Contrast 50 Color temp.
Input Signal Input signal Format for RGB DVI input signal (Timing) < Horizontal > Video Sync B D C E A H-parameters A: Total period B: Sync. width C: Back porch D: Active video E: Front porch Dot clock (MHz) Sync polarity H V 31.469 59.940 25.175 N 37.861 72.809 31.500 3 37.500 75.000 4 Item fH (kHz) Q R V-parameters O: Total period P: Sync.
A Guide to Simple Problem Solving Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Symptom Check these things ．Make sure the power cord is plugged in. ．Maybe the power is Off or Standby. ．Check whether the auxiliary equipment is connected. ．Check the input setting is correct. ．Signal may not be suitable.
Note 32
USER-INSTALLER CAUTION YOUR AUTHORITY TO OPERATE THIS FCC CERTIFIED EQUIPMENT COULD BE VOIDED IF YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THIS PART RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
