Personal Computer User Manual

ManualsBrandsToshiba ManualsDesktopP300

Satellite DynaBook V1, V2 Series Maintenance Manual (960-272)

Toshiba Personal Computer

Satellite P300

Maintenance Manual

TOSHIBA CORPORATION

File Number 960-Q08

Summary of content (334 pages)

PAGE 1
Toshiba Personal Computer Satellite P300 Maintenance Manual TOSHIBA CORPORATION File Number 960-Q08 Satellite DynaBook V1, V2 Series Maintenance Manual (960-272) 1
PAGE 2
Copyright © 2003 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Personal Computer Washington- Satellite A300 Maintenance Manual First edition Feb 2008 Disclaimer The information presented in this manual has been reviewed and validated for accuracy.
PAGE 3
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite A300 Series. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention. Each of these messages will be italicized and identified as shown below.
PAGE 4
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite A300 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.
PAGE 5
Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type.
PAGE 6
Table of Contents Chapter 1 Hardware Overview 1.1 Features ..........................................................................................................................1 1.2 System Block Diagram ..................................................................................................6 1.3 2.5-inch Hard Disk Drive.............................................................................................11 1.4 Optical Drive......................................................
PAGE 7
2.5 2.6 2.7 2.8 Procedure 1 Message Check ....................................................................... 15 Procedure 2 Debugging Port Check............................................................ 17 Procedure 3 Diagnostic Test Program Execution Check ............................ 22 Procedure 4 Replacement Check ................................................................ 22 USB FDD Troubleshooting .................................................................................
PAGE 8
2.9 2.10 2.11 2.12 2.13 2.14 2.15 2.15 Display Troubleshooting..............................................................................................38 Procedure 1 External Monitor Check...........................................................38 Procedure 2 Diagnostic Test Program Execution Check .............................38 Procedure 3 Connector and Cable Check ....................................................39 Procedure 4 Replacement Check ...................................
PAGE 9
3.5 Memory Test............................................................................................................ 3-13 3.6 Keyboard Test.......................................................................................................... 3-16 3.7 Display Test ............................................................................................................. 3-19 3.8 Floppy Disk Test...............................................................................................
PAGE 10
3.21. 5 How to enter data ……………………………………………………3-64 Chapter 4 4.1 Replacement Procedures Overview.................................................................................................................... 4-1 Safety Precautions................................................................................................ 4-2 Before You Begin ................................................................................................ 4-3 Disassembly Procedure...................................
PAGE 11
Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ................................................................................................ B-1 Appendix C Pin Assignments............................................................................................ C-1 Appendix D Keyboard Scan/Character Codes ..................................................................
PAGE 12
Satellite P300 Maintenance Manual (960-Q08) 12
PAGE 13
Chapter 1 Hardware Overview Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) I-1
PAGE 14
Chapter 1 Hardware Overview Chapter 1 Contents (Intel Platform) 1.1 Features ..........................................................................................................................1 1.2 System Block Diagram ..................................................................................................5 1.3 2.5-inch Hard Disk Drive...............................................................................................9 1.4 Optical Drive (DVD Super Multi Drive) ........
PAGE 15
Hardware Overview Chapter 1 Tables Table 1-1 2.5-inch HDD dimensions .................................................................................9 Table 1-2 2.5-inch HDD dimensions ...............................................................................10 Table 1-3 2.5-inch HDD specifications............................................................................11 Table 1-4 DVD Super Multi drive outline dimensions ....................................................
PAGE 16
Chapter 1 Hardware Overview Features 1.1 Features The Satellite P300 Satellite Pro P300 (Intel Platform) series are 2 spindle PCs running Intel® Core Duo Processor T8100 (800MHz) or higher Intel® Core Duo Processor T9300 (800MHz) or higher. Intel® Pentium Dual Processor T2330 or higher. Intel® Celeron 540 Processor or higher. Intel® Core™2 Duo Processor (667MHz) T5450 or higher. The features are listed below. θ Microprocessor Microprocessor that is used will be different by the model.
PAGE 17
Chapter 1 Hardware Overview Maximum upgradeable system memory may depend on the model θ VRAM Shared with System RAM for Intel GM965, PM965,GL960, GM965 +ATI M82XT Graphic card:64MB,128MB,256MB. θ HDD(First/Second Hard Drive – SATA) 160GB, 200GB, 250GB, 300GB, internal drives. 2.5 inch x 9.5mm height. θ USB FDD (Option) Toshiba external USB FDD for option θ Display LCD 17-inch, 1,440 (H) x 900 (V) WXGA+ 262,144 colors + CCFL, High-brightness, amorphous silicon TFT color display..
PAGE 18
Chapter 1 Hardware Overview It is good with no external power source for 1month on average. The main battery is a detachable lithium ion battery. 6 cell Li-Ion 10.8v/4000mAh 9 cell Li-Ion 10.8v/6000mAh θ USB (Universal Serial Bus) 3 USB ports are provided. The ports comply with the USB2.0 standard, which enables data transfer speeds 40 times faster than USB1.1 standard. USB1.1 is also supported.
PAGE 19
Chapter 1 Hardware Overview θ 3D Accelerometer for HDD Figure 1-1 Front of the computer SatelliteP300 Maintenance Manual (960-Q08) 4
PAGE 20
Chapter 1 Hardware Overview 1.2 System Block Diagram Figure 1-2 shows the system block diagram.
PAGE 21
Chapter 1 Hardware Overview The PC contains the following components. θ CPU Intel Core2 Duo Processor FSB : 667 MHz T5550(1.83GHz) T5750(2.0GHz) T5850(2.16GHz FSB : 800MHz T8100(2.10GHz) T8300(2.40GHz) T9300(2.5GHz) T9500(2.6GHz) Intel Pentium Dual FSB :533GHz T2330(1.6GHz) T2370(1.73GHz) T2390(1.86GHz) Intel Celeron FSB : 533 GHz 540(1.86GHz) 550(2.0GHz) 560(2.13GHz) 570(2.
PAGE 22
Chapter 1 Hardware Overview • North Bridge (Intel PM965,GM965/GL960) − − − − • Celeron processor System Bus support DRAM Controller : DDRII 533/667/800 support DMI 1299-ball 35 x 35mm Mirco FC-BGA Package South Bridge (Intel 82801HBM ICH8-M) − − − − − − − − − − − − − − − − Direct Media Interface (DMI) PCI Express Serial ATA (SATA) Controller PCI Interface Low Pin count (LPC) interface Serial Peripheral Interface (SPI) DMA controller Advanced Programmable Interrupt Controller (APIC) USB Controllers Giga
PAGE 23
Chapter 1 Hardware Overview θ MODEM (Conexant x 1) Supported by on board Modem + DAA daughter card. Data and FAX transmission is available. Supports ITU-TV.90. The transfer speed of data receiving is 56kbps, of data sending is 33.6kbps and of FAX is 14.4kbps. Actual speed depends on the quality of the line used.
PAGE 24
Chapter 1 Hardware Overview 1.3 2.5-inch Hard Disk Drive A compact, high-capacity HDD with a height of 9.5mm. Contains a 2.5-inch magnetic disk and magnetic heads. Figure 1-3 shows a view of the 2.5-inch HDD and Tables 1-1 and 1-2 list the specifications. Figure 1-3 2.5-inch HDD Table 1-1 2.5-inch HDD dimensions Standard value Parameter Outline dimens ions TOSHIBA MK1246GS X TOSHIBA MK1646GS X TOSHIBA MK2046GS X Width (mm) 69.85 +/- 0.25 Height (mm) 9.5 Depth (mm) 100.2 +/- 0.
PAGE 25
Chapter 1 Hardware Overview Parameter Standard value HITACHI HTS542512k9SA0 0 Outlin e dimen sions HITACHI HTS542516k9SA 00 HITACHI HTS542520k9SA 00 Width (mm) 69.85 +/- 0.25 Height (mm) 9.5 Depth (mm) 100.2 +/- 0.25 Weight (g) 95 (max.) 95 (max.) 102 (max.) HITACHI HTS542525k9S A00 102 (max.) Table 1-2 2.5-inch HDD dimensions Parameter Standard value FUJITSU MHX2250BT FUJITSU MHX2300BT 100 Outline Width (mm) dimensi ons Height (mm) 12.5 Depth (mm) 70.
PAGE 26
Chapter 1 Hardware Overview Table 1-3 2.5-inch HDD specifications Specification Parameter Storage size (formatted) TOSHIBA TOSHIBA MK1246G SX TOSHIBA MK1646GS X TOSHIBA MK2046G SX TOSHIBA MK2546G SX MK3252G SX 120GB 160GB 200GB 250 GB 320GB Speed (RPM) Data transfer Rate - To/From Media - T0/From Host 5,400 730Mbits Media 300MBytes Host 794Mbits Media 3GBytes Host 1.5Gbps(150MB/s) bus transfer rate (MB/s) Average random seek time (read) (ms) 12 Power-on-to-ready (sec) 3.5(typ)/9.
PAGE 27
Chapter 1 Hardware Overview Specification Parameter HITACHI HTS542512k9 SA00 HITACHI HTS542516k9S A00 HITACHI HTS542520k9SA 00 HITACHI HTS542525k9SA0 0 120GB 160GB 200GB 250GB Storage size (formatted) Speed (RPM) 5,400 Data transfer Rate - To/From Media - T0/From Host 65.5MB/s 1.5Gbps 65.5MB/s 1.5Gbps 65.5MB/s 1.5Gbps 65.5MB/s 1.5Gbps bus transfer rate (MB/s) 150 (MB/s Average random seek time (read) (ms) 11 Power-on-to-ready (sec) 3.
PAGE 28
Chapter 1 Hardware Overview 1.4 Optical drive (DVD Super Multi Drive) The DVD Super Multi drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) CD/DVD-ROM, CD-R/RW, DVD±R/±RW and DVD-RAM. It is a high-performance drive that reads DVD-ROM at maximum 8-speed and CD at maximum 24-speed. Write speed of DVD±R/±RW and DVD-RAM is different depending on the drive. The DVD Super Multi drive is shown in Figure 1-4.
PAGE 29
Chapter 1 Hardware Overview Table 1-5 DVD Super Multi drive specifications (1/4) Drive Specification Parameter Read (KB/s) TST TST PNR PNR TS-L632H TS-L632P DVR-KD08TBT DVR-KD08TBL CD-ROM 3600 KB/s CD-R 3600 KB/s CD-RW 3600 KB/s DVD-ROM(L) 10800 KB/s DVD+/-R Dual8100KB/s DVD-RAM 6750 KB/s CD-ROM 3600 KB/s CD-R 3600 KB/s CD-RW 3600 KB/s DVD-ROM(SL) 10800 KB/s DVD+/-R Dual 8100 KB/s DVD-RAM 6750 KB/s CDInner 1,545 Outer 3,600 (10.
PAGE 30
Chapter 1 Hardware Overview 2M Buffer memory 2M 2 Mbytes 2 Mbytes CD 650MB CDROMR(Rad Only) 80mm CD(Horizontal Mount only) 800/700/650 CDRecordable (Read & Write) 700/650 MB CD-Rewritable (Read & Write) 700/650MB High Speed CD-Rewritable (Read & Write) 700/650 MB Ultra Speed CD-Rewritable (Read & Write) Ultra+ Speed CD-Rewritable (Read Only) 650MB CDROMR(Read Only) 80mm CD(Horizontal Mount only) 800/700/650 CDRecordable (Read & Write) 700/650 MB CD-Rewritable (Read & Write) 700/650MB High Speed CD-Re
PAGE 31
Chapter 1 Hardware Overview 1.5 Keyboard The Satellite P300 keyboard has two different kinds of placement, one is for JP style and the other is for US/UK style Figure 1-5 is a view of the keyboard for US style Figure 1-5 Keyboard for US style Figure 1-6 is a view of the keyboard for UK style.
PAGE 32
Chapter 1 Hardware Overview Figure 1-7 is a view of the keyboard for JP style. Figure 1-7 Keyboard for JP style See Appendix E for details of the keyboard layout.
PAGE 33
Chapter 1 Hardware Overview 1.6 TFT Color Display The SatelliteP300 and Satellite Pro 300 Panel use CCFL to control backlight. 1.6.1 LCD Module with CCFL Backlight Figure 1-8 ~ 1-11 shows a view of the LCD module and Table 1-8 lists the specifications.
PAGE 34
Chapter 1 Hardware Overview Figure 1-9 AUO LCD Module Satellite P300 Maintenance Manual (960-Q08) 19
PAGE 35
Chapter 1 Hardware Overview Figure 1-10 CMO LCD Module SatelliteP300 Maintenance Manual (960-Q08) 20
PAGE 36
Chapter 1 Hardware Overview Figure 1-11 SAMSUNG LCD Module Table 1-6 LCD module specifications Specifications(WXGA+) Item LG-Philips AUO CMO Samsung LP171WP4-TLN1 B170PW06 N170C2-L02 LTN170X2-L02-S Number of Dots Dot spacing (mm) Display Colors Satellite P300 Maintenance Manual (960-Q08) 1,440 x 3(R,G,B) x 900 0.255(H)× 0.
PAGE 37
Chapter 1 Hardware Overview 1.6.2 CCFL Inverter Board Table 1-7 lists the FL inverter board specifications. Table 1-7 FL inverter board specifications Specifications Foxconn T18I095.00 Delta DAC-08N035 AF SUMIDA TWS-449-308 TDK TBD485NR Voltage (V) 8~20 8~20 8~20 8~20 Power (W) 7.5W 7.5W 7.5W 7.5W 612~945 612~945 612~945 612~945 Item Input Voltage (Vrms) Output Current (f=55KHz)(mArms) SatelliteP300 Maintenance Manual (960-Q08) 2.3±0.4 ~ 6.5±0.
PAGE 38
Chapter 1 Hardware Overview 1.7 Power Rails Table 1-8 lists the power rail output specifications of Santa Rosa platform. Table 1-8 Power supply output rating Power supply （Yes/No） Name Voltage [V] Power OFF Suspend mode Power OFF Boot mode No Battery +5VPCU 5 Yes Yes No +5V_S5 5 Yes No No +5V 5 No No No +5VSATA 5 No No No USBPWR1 5 No No No +5V_TP 5 No No No VCCRTC 3.3 Yes Yes Yes TH_FAN_POWER 3.1~5 No No No +3VPCU 3.3 Yes Yes No +3V_S5 3.
PAGE 39
Chapter 1 Hardware Overview 1.8 Batteries The PC has the following two batteries. θ Main battery θ Real time clock (RTC) battery Table 1-9 lists the specifications for these two batteries. Table 1-9 Battery specifications Battery Name Battery Element Sanyo 6 cell Panasonic Main battery Lithium ion 6 cell Sanyo 9 cell Real time clock (RTC) battery Panasonic ML1220/F1BEMOLEX-58ZL1 Lithium ion Output Voltage Capacity 10.8v 4000mAh 10.8v 4000mAh 10.8v 6000mAh 3V 17mAh 1.8.
PAGE 40
Chapter 1 Hardware Overview 1.8.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and detects a full charge when the AC adaptor and battery are connected to the computer. θ Battery Charge When the AC adapter is connected, normal charging is used while the system is turned on and quick charge is used while the system is turned off. Refer to the following Table 1-10.
PAGE 41
Chapter 1 Hardware Overview 1.8.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1-12 lists the Time required for charges of RTC battery and data preservation time.
PAGE 42
Chapter 1 Hardware Overview 1.9 AC Adapter The AC adapter is used to charge the battery. Table 1-13 lists the AC adapter specifications. Table 1-13 AC adapter specifications Parameter With Led Power Specification DELTA/ LITE-ON DELTA/ LITE-ON DELTA/ LITE-ON 75W 90W 120W Input voltage AC 100V/240V Input frequency 50Hz/60Hz Input current ≦1.5A Output voltage DC 19V Output current 3.95A Satellite P300 Maintenance Manual (960-Q08) 4.74A 6.
PAGE 43
Chapter 2 Troubleshooting Procedures Chapter 2 Contents 2.1 Troubleshooting ............................................................................................................ 1 2.2 Troubleshooting Flowchart........................................................................................... 3 2.3 Power Supply Troubleshooting..................................................................................... 8 2.4 2.5 Procedure 1 Power Status Check ................................
PAGE 44
2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 2.5” HDD Troubleshooting......................................................................................... 28 Procedure 1 Partition Check........................................................................ 29 Procedure 2 Message Check ....................................................................... 29 Procedure 3 Format Check..........................................................................
PAGE 45
Procedure 2 2.15 2.16 Replacement Check................................................................. 50 Fingerprint Troubleshooting .................................................................................... 51 Procedure 1 Diagnostic Test Program Execution Check ............................ 51 Procedure 2 Connector Check and Replacement Check............................ 51 Bluetooth Troubleshooting .........................................................................................
PAGE 46
2 Troubleshooting Procedures 2 2.1 Troubleshooting Chapter 2 describes how to determine which Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Power supply 6. Touch pad 11. Wireless LAN 2. System Board 7. Display 12. Sound 3. USB FDD 8. Optical Disk Drive 13, Finger Print Board 4. 2.5” HDD 9. Modem 14, Bluetooth 5. Keyboard 10. LAN The Test Program operations are described in Chapter 3.
PAGE 47
2 Troubleshooting Procedures There are following two types of connections in the figure of board and module connection in and after 2.3 Power Supply Troubleshooting. (1) Cable connection is described in the figure as line. (2) Pin connection is described in the figure as arrow.
PAGE 48
2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determining which troubleshooting procedures to execute. Before going through the flowchart steps, verify the following: Ask him or her to enter the password if a password is registered. Verify with the customer that Toshiba Windows is installed on the hard disk. NonWindows operating systems can cause the computer to malfunction. Make sure all optional equipment is removed from the computer.
PAGE 49
2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (1/2) Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4
PAGE 50
2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (2/2) Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 5
PAGE 51
2 Troubleshooting Procedures If the diagnostics program cannot detect an error, the problem may be intermittent. The Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an error(s), and then perform the appropriate troubleshooting procedures as follows: 1.
PAGE 52
2 Troubleshooting Procedures Procedures in Section 2.17.
PAGE 53
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting The power supply controller controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed.
PAGE 54
2 Troubleshooting Procedures Table 2-2 DC IN icon(Low cost) DC IN icon Power supply status Lights white(Green) DC power is being supplied from the AC adapter. Blinks white(Green) Power supply malfunction*1 Doesn’t light Any condition other than those above. *1 When the power supply controller detects a malfunction, the DC IN icon blinks white. It shows an error code. When the icon is blinking, perform the following procedure. 1. Remove the battery pack and the AC adapter. 2.
PAGE 55
2 Troubleshooting Procedures Procedure 2. Error Code Check The following table lists the error codes and error status names for the Diagnostic Tests.
PAGE 56
2 Troubleshooting Procedures Table2 -3 Error codes and error status names (2/2) Device Name HDD Cache Memory Multimedia Error Code Error Status Name BB Undefined Error CC Write Fault E0 Status Error F0 No Sense Error ?? Other Error 02 Protect Mode Error 03 Caching Error ?? Other Error 01 Write Error 0F Invalid Drive 15 Drive Not Ready ?? Other Error NOTE: If error status name is Other Error , please reference the Error Code for error information Satellite P300 and Satellite Pro
PAGE 57
2 Troubleshooting Procedures Procedure 3 Connection Check The wiring diagram related to the power supply is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Make sure the AC adapter and the AC power cord is firmly plugged into the DC IN connector PCN4 (REV.G and Griffin) and wall outlet. If these cables are connected firmly, go to Check 2. Check 2 Replace the AC adapter and the AC power cord with new ones.
PAGE 58
2 Troubleshooting Procedures following procedures: Check 1 Make sure the AC adapter is firmly plugged into the DC IN socket. Check 2 Make sure the battery pack is properly installed. If it is properly installed, go to Check 3. Check 3 The battery pack may be completely discharged. Wait a few minutes to charge the battery pack while connecting the battery pack and the AC adapter. If the battery pack is still not charged, go to Check 4. Check 4 The battery’s temperature is too high or low.
PAGE 59
2 Troubleshooting Procedures Procedure 5 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following Checks. To disassemble the computer, follow the steps described in Chapter 4, Replacement Procedures. When AC adapter is connected; Check 1 AC adapter may be faulty. Replace the AC adapter with a new one. If the problem still occurs, perform Check 2. Check 2 System board may be faulty.
PAGE 60
2 Troubleshooting Procedures 2.4 System Board Troubleshooting This section describes how to determine if the system board is malfunctioning or not. Start with Procedure 1 and continue with the other procedures as instructed.
PAGE 61
2 Troubleshooting Procedures Procedure 1 Message Check When the power is turned on, the system performs the Power On Self Test (POST) installed in the BIOS ROM. The POST tests each IC on the system board and initializes it. If an error message is shown on the display, perform Check 1. If there is no error message, go to Procedure 2. If MS-DOS or Windows XP is properly loaded, go to Procedure 4.
PAGE 62
2 Troubleshooting Procedures If any other error message displays, perform Check 3. Check 3 The IRT checks the system board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) through (17), (24) or (25) is displayed, go to Procedure 4. If error message (18) is displayed, go to the Keyboard Troubleshooting Procedures. If error message (19), (20) or (21) is displayed, go to the 2.5” HDD Troubleshooting Procedures.
PAGE 63
2 Troubleshooting Procedures Procedure 2 Debugging Port Check Check the MiniPCI Debug board. The tool for debug port test is shown below. Figure 2-2 A set of tool for debug port test The test procedures are follows: 1. Replace Mini PCI debug port with Wireless LAN card, check LED in the Mini PCI debug board The following is a list of the Test Point codes written to port 80h at the start of each routine, the beep codes issued for terminal errors, and a description of the POST routine.
PAGE 64
2 Troubleshooting Procedures 13h Initialize PCI Bus Mastering devices Code Beeps POST Routine Description 14h Initialize keyboard controller 16h 1-2-2-3 BIOS ROM checksum 17h Initialize cache before memory autosize 18h 8254 timer initialization 1Ah 8237 DMA controller initialization 1Ch Reset Programmable Interrupt Controller 20h 1-3-1-1 Test DRAM refresh 22h 1-3-1-3 Test 8742 Keyboard Controller 24h Set ES segment register to 4 GB 26h Enable A20 line 28h Autosize DRAM 29h Initialize POST Memory Manager 2A
PAGE 65
2 Troubleshooting Procedures 62h 64h 66h 67h 68h 69h 6Ah 6Bh 6Ch 6Eh 70h 72h 76h 7Ch 7Eh 80h 81h 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 8Ch 8Fh 90h 91h 92h 93h 95h 96h 97h 98h 1-2 Test extended memory address lines Jump to UserPatch1 Configure advanced cache registers Initialize Multi Processor APIC Enable external and CPU caches Setup System Management Mode (SMM) area Display external L2 cache size Load custom defaults (optional) Display shadow-area message Display possible high address for UMB recovery
PAGE 66
2 Troubleshooting Procedures A2h Check key lock A4h Initialize Typematic rate A8h Erase F2 prompt Code Beeps POST Routine Description AAh Scan for F2 key stroke ACh Enter SETUP AEh Clear Boot flag B0h Check for errors B2h POST done - prepare to boot operating system B4h 1 One short beep before boot B5h Terminate QuietBoot (optional) B6h Check password (optional) B9h Prepare Boot Bah Initialize DMI parameters BBh Initialize PnP Option ROMs BCh Clear parity checkers BDh Display MultiBoot menu BEh Clear scree
PAGE 67
2 Troubleshooting Procedures Code Beeps For Boot Block in Flash ROM E0h Initialize the chipset E1h Initialize the bridge E2h Initialize the CPU E3h Initialize system timer E4h Initialize system I/O E5h Check force recovery boot E6h Checksum BIOS ROM E7h Go to BIOS E8h Set Huge Segment E9h Initialize Multi Processor EAh Initialize OEM special code EBh Initialize PIC and DMA ECh Initialize Memory type EDh Initialize Memory size EEh Shadow Boot Block EFh System memory test F0h Initialize interrupt vectors F1h
PAGE 68
2 Troubleshooting Procedures Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the system board. Refer to Chapter 3, Tests and Diagnostic, for more information on how to perform these tests. 1. System test 2. Memory test 3. Keyboard test 4. Display test 5. Floppy Disk test 6. VGA test 7. VGA Memory test 8. Hard Disk test 9. CPU Temperature test 10. Main Battery test 11. BIOS test 12. CD-ROM/DVD-ROM test 13.
PAGE 69
2 Troubleshooting Procedures 2.5 USB FDD Troubleshooting To check if the USB FDD is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: FDD Head Cleaning Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector Check and Replacement Check Procedure 1 FDD Head Cleaning Check FDD head cleaning is one option available in the Diagnostic Program. After connecting USB FDD, insert the Diagnostics Disk in the floppy disk drive.
PAGE 70
2 Troubleshooting Procedures Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test procedures. Make sure the floppy disk is formatted correctly and that the write protect tab is disabled. Floppy disk drive test error codes and their status names are listed in Table 2-7.
PAGE 71
2 Troubleshooting Procedures Procedure 3 Connector Check and Replacement Check USB FDD is connected to USB port on system board and US board. US board is also connected to system board by cable. The connection of cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks. USB FDD can be connected to the following 4 ports on system board.
PAGE 72
2 Troubleshooting Procedures Check 2 USB FDD may be faulty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 Connect USB FDD to each port embedded on system board. If it does not work properly when connected to CN6, CN7, CN31, CN35 or all ports, perform Check 4. Check 4 System board may be faulty. Replace it with a new one following the steps in Chapter 4, Replacement Procedures.
PAGE 73
2 Troubleshooting Procedures 2.6 2.5” HDD Troubleshooting To check if 2.5” HDD is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Partition Check Procedure 2: Message Check Procedure 3: Format Check Procedure 4: Diagnostic Test Program Execution Check Procedure 5: Connector Check and Replacement Check CAUTION: The contents of the hard disk will be erased when the 2.5” HDD troubleshooting procedures are executed.
PAGE 74
2 Troubleshooting Procedures Procedure 2 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. When the test detects an error, an error message is displayed on the screen. Make sure no floppy disk is in the FDD. Turn on the computer and check the message on the screen. When an OS starts from the 2.5” HDD, go to Procedure 3. Otherwise, start with Check 1 below and perform the other checks as instructed.
PAGE 75
2 Troubleshooting Procedures Procedure 3 Format Check The computer’s HDD is formatted using the MS-DOS FORMAT program or the physical format program of the test program. To format the HDD, start with Check 1 below and perform the other steps as required. Refer to the MS-DOS Manual for the operation of MS-DOS. For the format by the test program, refer to the Chapter 3. Check 1 Format an 2.5” HDD using MS-DOS FORMAT command. Type as FORMAT C:/S/U. If 2.5” HDD can not be formatted, perform Check 2.
PAGE 76
2 Troubleshooting Procedures Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnostics Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD test program. If an error is detected during the HDD test, an error code and status will be displayed. The error codes and statuses are described in Table 2-8.
PAGE 77
2 Troubleshooting Procedures Procedure 5 Connector Check and Replacement Check HDD(s) is/are connected to the connector(s) on the system board. The connection of HDD(s) and board may be defective. Otherwise, they may be faulty. Disassemble the computer following instructions in Chapter 4, Replacement Procedures and perform the following checks. Check 1 Make sure HDD(s) is/are firmly connected to the connector(s) on the system board.
PAGE 78
2 Troubleshooting Procedures 2.7 Keyboard Troubleshooting To check if the computer’s keyboard is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Keyboard Test (DIAGNOSTIC TEST) and Pressed key display test (ONLY ONE TEST) in the Diagnostic Program.
PAGE 79
2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure keyboard cable is firmly connected to system board. If the connection is loose, reconnect firmly and repeat Procedure 1. If the problem still occurs, go to Check 2. Check 2 Keyboard may be faulty.
PAGE 80
2 Troubleshooting Procedures 2.8 Touch pad Troubleshooting To check if the computer’s touch pad is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Touch pad test (ONLY ONE TEST) in the Diagnostic Program. Refer to Chapter 3, Tests and Diagnostics, for more information on how to perform the test program.
PAGE 81
2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the cable is firmly connected to system board. If the connection is loose, reconnect firmly and repeat Procedure 1. If the problem still occurs, go to Check 2. Check 2 Touch Pad or the cable may be faulty.
PAGE 82
Troubleshooting Procedures 2.9 Display Troubleshooting To check if the computer’s display is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External Monitor Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector and Cable Check Procedure 4: Replacement Check Procedure 1 External Monitor Check Connect an external monitor to the computer’s external monitor port, then boot the computer.
PAGE 83
Troubleshooting Procedures Procedure 3 Connector and Cable Check LCD Module is connected to system board by an LCD/FL cable. FL inverter board is also connected to system board by an LCD/FL cable. And, fluorescent lamp is connected to FL inverter board by HV cable. Their cables may be disconnected from system board or FL inverter board. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures. If the connection is loose, reconnect firmly and restart the computer.
PAGE 84
Troubleshooting Procedures Procedure 4 Replacement Check Fluorescent lamp, FL inverter, LCD module, HV cable and LCD/FL cable are connected to display circuits. Any of these components may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: If fluorescent lamp does not light, perform Check 1. If characters or graphics on the internal display are not displayed clearly, perform Check 4.
PAGE 85
Troubleshooting Procedures 2.10 Optical Disk Drive Troubleshooting To check if optical disk drive is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the CD-ROM/DVD-ROM Test in the Diagnostic Program. Refer to Chapter 3, Tests and Diagnostics for more information on how to perform the test program.
PAGE 86
Troubleshooting Procedures Chapter 4. If the problem still occurs, perform Check 3. Check 3 System board may be faulty. Replace it with new one following the instructions in Chapter 4.
PAGE 87
Troubleshooting Procedures 2.11 Modem Troubleshooting To check if modem is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute Modem test in the LAN/Modem/Bluetooth/IEEE1394 test program. Refer to Chapter 3, Tests and Diagnostics for more information on how to perform the test program.
PAGE 88
Troubleshooting Procedures Check 1 Make sure the following connections are firmly connected. If any connector is disconnected, connect it firmly and return to Procedure 1. If the problem still occurs, perform Check 2.
PAGE 89
Troubleshooting Procedures Check 2 Modem cable may be faulty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 MDC may be faulty. Replace it with a new one following the steps in Chapter 4. If the problem still occurs, perform Check 4. Check 4 Cable between MDC and system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the problem still occurs, perform Check 5. Check 6 System board may be faulty.
PAGE 90
Troubleshooting Procedures 2.12 LAN Troubleshooting To check if the computer’s LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute LAN test in the LAN/Modem test program. Refer to Chapter 3, Tests and Diagnostics for more information on how to perform the test program.
PAGE 91
Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting To check if the computer's Wireless LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Transmitting-Receiving Check Procedure 2: Antennas' Connection Check Procedure 3: Replacement Check Procedure 1 Transmitting-Receiving Check Before starting the test, make sure the wireless communication switch is set in the ON position.
PAGE 92
Troubleshooting Procedures Procedure 2 Antennas' Connection Check The wireless LAN function-wiring diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the wireless communication switch is “On”. If the switch is “Off”, turn it “On”. If the problem still occurs, perform Check 2.
PAGE 93
Troubleshooting Procedures Procedure 3 Replacement Check Wireless LAN card, wireless LAN antenna or system board may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Wireless LAN antenna may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. If the problem still occurs, perform Check 2. Check 2 Wireless LAN card may be faulty.
PAGE 94
Troubleshooting Procedures 2.14 Sound Troubleshooting To check if the sound function is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check Procedure 2: Procedure 1 Replacement Check Connector Check The connection of sound system is shown in the following figure. As the connection may be defective, disassemble the PC and check each connection. If the problem still occurs, go to Procedure 2.
PAGE 95
Troubleshooting Procedures Procedure 2 Replacement Check If External microphone/Headphone does not work properly, perform check 1. If Internal microphone /Speaker does not work properly, perform check 2. If HP out does not work properly, perform check 3. If Volume control does not work properly, perform check 4. Check 1 External microphone/Headphone may be faulty. Replace it with a new one following the steps in Chapter 4. Check 2 Internal microphone /Speaker may be faulty.
PAGE 96
Troubleshooting Procedures 2.15 Fingerprint Troubleshooting To check if the computer’s Fingerprint is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute Fingerprint test in the test program. Refer to Chapter 3, Tests and Diagnostics for more information on how to perform the test program. If any error is detected, perform Procedure 2.
PAGE 97
Troubleshooting Procedures Chapter 4.
PAGE 98
Troubleshooting Procedures 2.16 Bluetooth Troubleshooting To check if the computer’s Bluetooth is malfunctioning or not, follow the troubleshooting procedure below as instructed. Procedure 1: Connector Check and Replacement Check Procedure 1 Connector Check and Replacement Check The Bluetooth function is connected to system board. If Bluetooth malfunctions, its connection is defective or Bluetooth cable and system board may be faulty.
PAGE 99
Troubleshooting Procedures Satellite P300 and Satellite Pro P300 Maintenance Manual 54
PAGE 100
Test Program for Field.
PAGE 101
Test Program for Field. Chapter 3 Contents 3.1 Tests and Diagnostics Software Overview ............................................................... 3 3.2 Executing the Diagnostic Test .................................................................................. 4 3.3 Subtest names............................................................................................................ 8 3.4 System Test................................................................................................
PAGE 102
Test Program for Field. 3.1 Tests and Diagnostics Software Overview This chapter explains how to use the Tests and Diagnostics Software for the Satellite P300 and Satellite Pro P300 computer systems. NOTES: Before starting the Tests and Diagnostics software: 1. Check all cables for loose connections. 2. Exit any application and close Windows.
PAGE 103
Test Program for Field. 3.2 Executing the Diagnostic Test DOS is required to run the Diagnostics Program. To start the programs follow these steps: 1. Create a DOS bootable disk and copy all the files from the Tests and Diagnostics software to the disk. 2. Insert the boot disk into the computer’s floppy disk drive and turn on the computer. The following screen displays: TOSHIBA Satellite(Pro) P300 Diagnostics Version v1.10 ESC ::Select item :Escape [ DIAGNOSTICS MENU ] 01.DIAGNOSTIC TEST 02.
PAGE 104
Test Program for Field. The following menu displays: TOSHIBA Satellite(Pro) P300 Diagnostics Version V1.10 ESC ::Select item :Escape [ DIAGNOSTICS MENU ] 01. 02. 03. 04. 05. 01. 01. 06. 02. 99. 03. 04. 05. 06. 07. DIAGNOSTIC TEST RUNNING TEST DMI INFORMATION [ DIAGNOSTIC TEST MENU ] LOG UTILITIES SYSTEM CONFIGURATION SYSTEM TEST TEST 08. CACHE MEMORY TEST SYSTEM OPTION MEMORY TEST 09. HIGH RESOLUTION DISPLAY TEST EXIT KEYBOARD TEST 10. MULTIMEDIA TEST DISPLAY TEST 11. MEMORY2 TEST FLOPPY DISK TEST 88.
PAGE 105
Test Program for Field. 4. Select the subtest you want to execute and press Enter. The following menu displays: TOSHIBA Satellite(Pro) P300 Diagnostics Version V1.10 ESC : :Select item :Escape [ DIAGNOSTICS MENU ] [ SYSTEM TEST ] 01. DIAGNOSTIC TEST 02. RUNNING TEST 01. FAN ON/OFF 03. DMI INFORMATION 01. FAN ON/OFF 02.TEST Battery [ DIAGNOSTIC MENU Test ] 04. LOG UTILITIES 03. CPU Temperature 05. SYSTEM CONFIGURATION DIAGNOSTIC TEST MENU 01. SYSTEM 01.OPTION SYSTEM TEST TEST 9. 99.
PAGE 106
Test Program for Field. NOTES: The Item2 and 3 of Test Parameter are not used by some tests. Go To Test Move the highlight bar to Go To Test and press Enter to start executing the test. Test Loop Select NO to return the screen to the subtest menu after the test is complete. Select YES to set the test to run continuously until it is halted by the user. Error Stop Select NO to keep the test running even if an error is found.
PAGE 107
Test Program for Field. 3.3 Subtest names Table 3-1 lists the subtest names for each test program in the Diagnostic Test menu. Table 3-1 Subtest Names(1/3) No. 01 02 03 04 8 Test Name SYSTEM TEST MEMORY TEST KEYBOARD TEST DISPLAY TEST No.
PAGE 108
Test Program for Field. Table 3-1 Subtest Names(2/3) No. 05 06 07 08 09 Test Name No.
PAGE 109
Test Program for Field. Table 3-1 Subtest Names(3/3) No. 10 11 Test Name MULTIMEDIA TEST MEMORY2 No. Subtest Name 01 Sequential Read Test 02 Random Read Test 03 Read Specified Address Test 04 1 point W/R/C Test 01 All one/zero Test 02 Walking 1/Walking 0 Test(Left) 03 Walking 1/Walking 0 Test(Right) 04 Walking 1/Walking 0 Test(Left /Right) *This test cannot support.
PAGE 110
Test Program for Field. 3.4 System Test To execute the System Test select 01 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The System Test contains three subtests. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 FAN ON/OFF Checking Select 1,2,3 to control FAN on/off , 1=Fan on , 2=Fan off , 3=Exit . [BU1FAN.EXE] Program Version : 1.
PAGE 111
Test Program for Field. Subtest 03 CPU Temperature This will display CPU Temperature for check , press [ESC] to exit . [CPU_TEMP.EXE] Program Version : 1.
PAGE 112
Test Program for Field. 3.5 Memory Test To execute the Memory Test select 02 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Memory Test contains five subtests that test the computer’s memory. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: If NO is selected for Test Loop on the Test Parameter menu, the Test Status screen displays while the test is executing. When the test is complete the Memory Test menu displays.
PAGE 113
Test Program for Field. 5. Address pattern test “16 bit write and 16 bit read” of address pattern data is executed and the new data is compared with the original data. Test data = 0000H, 0004H, 0008H, 000CH,...8000H, 8004H, through FFECH Subtest 02 Protected Mode This subtest first writes data patterns and address data from 1 to 32 MB, then reads the new data and compares the result with the original data patterns. Addresses are displayed in 64KB increments during the test. . Test Process: 1.
PAGE 114
Test Program for Field. with the original data patterns. Addresses are displayed in 64KB increments during the test. Test Process: 1. Byte Enable Test One bit write/ 8 bit read” is executed and the new data is compared with the original data. Test data = CCAA5533H, 80000000H 2. Byte Enable Test “One bit write/16 bit read” is executed and the new data is compared with the original data. Test data = CCAA5533H, 80000000H 3.
PAGE 115
Test Program for Field. Test Process: 1. Checks the memory size to determine the maximum size of installed memory. 2. Tests memory addresses 0 to the maximum installed. 3. Writes, reads, and compares test data after a memory refresh cycle (16ms or more). NOTE: There may be a short delay between write and read operations, depending on the memory size. Subtest 05 Stress Test This subtest writes the following 16KB data patterns to the Write/Read Buffer in conventional memory.
PAGE 116
Test Program for Field. 3.6 Keyboard Test To execute the Keyboard Test select 03 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Keyboard Test contains five subtests that test the computer’s keyboard and mouse actions. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: The Test Loop and Error Stop parameters are not enabled for the Keyboard test.
PAGE 117
Test Program for Field. Subtest 04 Hot Key Display [7 Key] This subtest is used for the 7 hot key and functions the same as Subtest 1. MUTE MUSIC PLAY STOP BACK NEXT WLAN Subtest 05 Hot Key Display [1 Key] This subtest is used for the 1 hot key and functions the same as Subtest 1. WLAN Subtest 06 PS/2 Mouse (Pointing) This subtest checks the function of mouse as shown below.
PAGE 118
Test Program for Field.
PAGE 119
Test Program for Field. 3.7 Display Test To execute the Display Test select 04 from the Diagnostic Test Menu, press Enter and follow the directions displayed on the screen. The Display Test contains twelve subtests that test the display in various modes. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Character Attributes This subtest displays character attributes and color attributes. The character attributes are: normal, intensified, reverse, and blinking.
PAGE 120
Test Program for Field. Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Subtest 02 Character Set This subtest displays the character codes 00H - FFH, using Mode 01H (40*25). The screen below displays when this subtest is executed.
PAGE 121
Test Program for Field. Subtest 03 80 * 25 Character Display This subtest uses 80*25 video resolution to display character codes 20H 7EH using Mode 03H (80*25). The data displayed is shifted 1 byte to the left for each line as shown below. 80*25 CHARACTER DISPLAY 01234567890123456789012345678901234567890123456789012345678901234567890123456789 !”#$%&’()*=,.-/0123456789:;Ù?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_’abcdefghIjklmno !”#$%&’()*=,.
PAGE 122
Test Program for Field. Subtest 04 320 * 200 Character Display This subtest uses 320*200 video resolution to display green, red and yellow followed by cyan, magenta, and white. The screen below shows the displays when this subtest is executed.
PAGE 123
Test Program for Field. 320*200 GRAPHICS DISPLAY BLACK : [ D ] D GRAY BLUE L BLUE GREEN L GREEN CYAN L CYAN RED L RED MAGENTA L MAGENTA BROWN YELLOW WHITE I WHITE Press [Enter] KEY Press ENTER to display 64 gradations of red, green, blue and white on the screen 320*200 GRAPHICS DISPLAY : [ 13 ] 64 gradations of red are displayed. 64 gradations of green are displayed. 64 gradations of blue are displayed. 64 gradations of white are displayed.
PAGE 124
Test Program for Field. Subtest 05 640 * 200 Character Display This subtest uses 640*200 video resolution to display three windows, each window drives a different set of dots: even dots, odd dots and all dots. The screen below displays when this subtest is executed.
PAGE 125
Test Program for Field. Subtest 06 640 * 480 Character Display This subtest uses 640*350 video resolution to display 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is executed.
PAGE 126
Test Program for Field. 640*480 GRAPHICS DISPLAY : [12 ] BLACK DARK GRAY BLUE LIGHT GREEN LIGHT GREEN CYAN LIGHT CYAN RED LIGHT RED MAGENTA LIGHT MAGENTA BROWN YELLOW WHITE INTENSIFIED WHITE BLUE Press [Enter] KEY To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu.
PAGE 127
Test Program for Field. Subtest 07 Display Page This subtest displays video pages zero through seven. DISPLAY PAGE 0 000000000000000000000000000000000000000000000000000000000000000 ............................................................0 0............................................................0 0............................................................0 0............................................................0 0............................................................0 0...............
PAGE 128
Test Program for Field. Subtest 08 "H" Pattern Display This subtest displays a full screen of "H" patterns.
PAGE 129
Test Program for Field. Subtest 10 Color Graphics Display This subtest displays three colors, cyan, white and yellow on the screen as shown below. 640 * 480 GRAPHICS DISPLAY CYAN WHITE YELLOW To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu.
PAGE 130
Test Program for Field. Subtest 11 Color Attributes Display This subtest displays 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is executed.
PAGE 131
Test Program for Field. NOTE: The following screen does not display correctly. It will be amended in the next version. Press [Enter] Key Press Enter to execute the VRAM mapping test which displays a vertical line at four dot intervals using Mode 12. Press [Enter] Key Press Enter to display VRAM mapping test using the all dots Mode.
PAGE 132
Test Program for Field. Press [Enter] Key To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu.
PAGE 133
Test Program for Field. Subtest 12 Color Tiling This subtest displays black, gray, white, and 3 gradations of red, green, and blue as shown in the following display. Black Red Green Blue Gray Red Gradation Green Gradation Blue Gradation White Red Gradation Green Gradation Blue Gradation To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu.
PAGE 134
Test Program for Field. 3.8 Floppy Disk Test CAUTION: Before running the floppy disk test, prepare a formatted work disk. Remove the diagnostics disk and insert the work disk into the FDD. The contents of the floppy disk will be erased. To execute the Floppy Disk Test select 05 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Floppy Disk Test contains five subtests that test the FDD. Move the highlight bar to the subtest you want to execute and press Enter.
PAGE 135
Test Program for Field. Subtest 04 Write Specified Address NOTE: The first two digits of the ADDRESS indicate which track is being tested, the next two digits indicates the head, and the last two digits indicate the sector. This subtest allows you to verify the errors from Subtest 02. It writes specified data to a specified track and head. Use the Log Utilities (see Section 3.21) to specify the track number and head number where the error(s) occurred during Subtest 02.
PAGE 136
Test Program for Field. 3.9 Hard Disk Test To execute the Hard Disk Test select 06 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Hard Disk Test contains eight subtests that test the functions of the hard disk drive. Move the highlight bar to the subtest you want to execute and press Enter. NOTES: The contents of the hard disk will be erased when subtest 02, 03, 04, 05, 07 or 08 is executed.
PAGE 137
Test Program for Field. Subtest 04 Cross Talk and Peak Shift This subtest writes eight of the most likely to fail data patterns (shown below) to a cylinder on the HDD, then reads the data while moving from cylinder to cylinder. Data Pattern B5ADADH 4A5252H EB6DB6H 149249H 63B63BH 9C49C4H 2DB6DBH D24924H Subtest 05 Write Specified Address NOTE: This subtest is designed to run with the Test Loop set to NO. This subtest is a debug tool and the operator should enter the Test Parameters each time. .
PAGE 138
Test Program for Field. Subtest 07 Sequential Write This subtest writes specified data to all cylinders on the HDD. The following message displays on the screen to enter the test data. TEST DATA Subtest 08 ????(=37b3H) W-R-C Specified Address This subtest writes specified data to a specified sector count, then reads and compares the result. The following message displays on the screen to enter the test data, sector count.
PAGE 139
Test Program for Field. 3.10 Real Time Clock Test To execute the Real Time Clock Test select 07 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Real Time Clock Test contains three subtests that test the computer’s real time functions. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Real Time This subtest allows you to change the date and time. To execute the Real Time Subtest, follow these steps: 1.
PAGE 140
Test Program for Field. Subtest 02 Backup Memory This subtest writes 50 bytes of test data (FFH, AAH, 55H, and 00H) to the CMOS 14th address, then reads the new data and compares it to the original data. Subtest 03 Real Time Carry CAUTION: When this subtest is executed, the current date and time are reset. This subtest checks the clock’s carry function.
PAGE 141
Test Program for Field. 3.11 Cache Memory Test To execute the Cache Memory Test select 08 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Cache Memory Test contains eight subtests that test the computer's cache memory. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: If NO is selected for Test Loop on the Test Parameter menu, the screen will remain blank while the subtest is executing.
PAGE 142
Test Program for Field. Subtest 04 Bit Shift Pattern Test This subtest reads the contents of cache memory and saves it into RAM. The subtest then writes the bit shift data patterns (1 bit shifted every 4 bytes), reads the new data and compares the result with the original data. The original cache memory content is then restored to the cache memory. Subtest 05 Write Disturb Test (We can’t support this time) This subtest reads the contents of cache memory and saves it into RAM.
PAGE 143
Test Program for Field. 3.12 High Resolution Display Test To execute the High Resolution Display Test select 09 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The High Resolution Display Test contains six subtests that test the computer's high resolution video display. Move the highlight bar to the subtest you want to execute and press Enter.
PAGE 144
Test Program for Field. Subtest 02 640*480 Mode Display This subtest uses 640*480 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below.
PAGE 145
Test Program for Field. Subtest 03 800 * 600 Mode Display This subtest uses 800*600 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 256 gradations of white, red, green, and blue as shown below.
PAGE 146
Test Program for Field. Subtest 04 1024* 768 Mode Display This subtest uses 1024*768 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below.
PAGE 147
Test Program for Field. Subtest 05 “H” Pattern Display This subtest uses the 1024*768 Mode to display a high resolution white frame, “H” letters (8*16 pixels fonts), at 128 letters by 48 lines.
PAGE 148
Test Program for Field. Subtest 06 Focus Test ( “E” Pattern) This subtest sets the 1024*768 Mode and displays “E” patterns (18*18 dot fonts), at 56 letters *42 lines surrounded by a high resolution white frame. To exit this subtest and return to the High Resolution Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu.
PAGE 149
Test Program for Field. 3.13 Multimedia Test To execute the Multimedia Test select 10 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Multimedia Test contains four subtests that test the computer's multimedia functions. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: Use the Toshiba Backup CD-ROM for Subtests 01, 02, and 03.
PAGE 150
Test Program for Field. 3.14 MEMORY2 Test To execute the Expansion Test select 11 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The MEMORY2 Test contains four subtests that test the computer's. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: If NO is selected for Test Loop on the Test Parameter menu, the Test Status screen displays while the test is executing. When the test is complete the Memory Test menu displays.
PAGE 151
Test Program for Field. Tee test method is the same as Subtest2. However, the data to be used differs.
PAGE 152
Test Program for Field. 3.15 Error Codes and Error Status Names The following table lists the error codes and error status names for the Diagnostic Tests.
PAGE 153
Test Program for Field.
PAGE 154
Test Program for Field. 3.16 Running Test NOTES: 1. You may add or delete subtests using the Running Test Edit Item function, see Section 3.20. 2. Do not forget to insert a work disk in the FDD. If a work disk is not inserted an error will be generated during the Floppy Disk Test. 3. If the test completes successfully an “PASS” sign with blue letters displays on the screen. 4. If the test fails or is interrupted before completion an “FAIL” sign with red letters displays on the screen. 5.
PAGE 155
Test Program for Field. 3.17 DMI INFOEMATION Select 03 from the Diagnostics Menu and press Enter to Check or Write DMI Information Data: 3.17.1 Check DMI Information The Check DMI Configuration program contains the following configuration information for the computer: NOTE: Please set the media of DVD before starting a test. System information (Type 1) 1. Manufacture : TOSHIBA 2. Product Name : Satellite XXXXXX 3. Version :(TOSHIBA Part Number) 4. Serial Number : Serial Number 5.
PAGE 156
Test Program for Field. 9. Project Identifier [1]LCD13”[2]LCD14”[3]LCD15”[4]LCD17” a. SLP2.0 Build Sig [1]Non OS [2]OS b. Wireless LAN ID (001E4CXXXXXX) Select 1 ~ b to keyin new data , select 0 to exit program , program will compare input data length with the max length , if over will retry keyin Note : Please Check New DMI Information After System Restart !! V2.6 1. **** Manufacture Name ( TOSHIBA ) - (15) 2. **** Product Name ( Satellite XXXXXX ) - (31) 3. **** Part Number ( PSL20X-XXXXXX ) - (15) 4.
PAGE 157
Test Program for Field. 3.17.
PAGE 158
Test Program for Field. 3.18 Log Utilities This function logs error information generated while a test is in progress and stores the results in RAM (Maximum error log : 500 times). This function can store data on a floppy disk. If the power switch is turned off, the error information will be lost. Error information is displayed in the following order: 1. 2. 3. 4. 5. 6. 7. 8.
PAGE 159
Test Program for Field. 2. Error information displayed on the screen can be manipulated with the following number keys: The 1 key scrolls the display to the next page. The 2 key scrolls the display to the previous page. The 3 key returns to the Diagnostics Menu. The 4 key erases all error log information in RAM. The 5 key reads the log information from a floppy disk. The 6 key writes the log information to a floppy disk. The 7 key save the log information to a floppy disk.
PAGE 160
Test Program for Field. 3.19 System Configuration Select 05 from the Diagnostics Menu and press Enter to display the following system configuration: SYSTEM CONFIGURATION : * * * * - * * * * * - BIOS VER = VX.XX KBC VER = XXXX MAC ADDRESS : XXXXXXXXXXXX 0 ASYNC ADAPTER 1 HDD DRIVE(S):XXXXXXXXXXXXXXXXXXXXXXXXXX FW Rev.:XXXXXXXX CUR LBA:XXXXXXXX ORG LBA:XXXXXXXX BATTERY TYPE:XXXXXXXXXX XXXMB MEMORY SIZE XXX CPU 1 Vedio Chip XXXXXXXXXXXXX 1 ODD DRIVE(S):XXXXXXXX FW Rev.
PAGE 161
Test Program for Field. 3.20 Running Test Edit Item 3.20.1 Function Description Function description lets you add or delete the subtests used to execute the Running Test. The following screen displays after pressing the Tab key to edit an item in the Running Test. KEY OPERATION Ð Ï PgDn PgUp Home End Ins Del Enter Cursor Down Cursor Up Page Down Page Up Top of ITEM End of ITEM Insert ITEM Delete ITEM End 3.20.
PAGE 162
Test Program for Field. 1. Enter a number or 0 for Loop Count and press Enter. Select a number from 1 to 65535 to define the number of times the Running Test executes. Select 0 to run the test continuously until halted by the user. 2. Select the NO or YES for Error Stop and press Enter. Select NO to keep the test running even if an error is found. Select YES to stop the test program when an error is found. NOTE: All errors which occur during execution of the Running Test are logged in the Log File. 3.
PAGE 163
Test Program for Field. 3.21 Common Tests and Operation 3.21.1 How to operate a window To input parameters, or open a window use the following keys. key [Enter] key [Esc] key : to move a highlight bar : to select an item at the highlight bar : to close the current window and go back to the previous window 3.21.2 How to Stop the Test Program To stop a test: [Ctrl]+[Break] Press the Ctrl key and the Break key simultaneously. 3.21.
PAGE 164
Test Program for Field. Pass Count Displays the number of times the test has been executed. Error Count Displays the number of errors which have occurred during the test. Write Data Displays only the test data that has failed to compare during the test while being written during the test. Read Data Displays test data that has failed to compare during the test while being read during the test. Test Address Displays the Test Address. (The format differs for each test.
PAGE 165
Test Program for Field. 3.21.4 Test Stop Display If an error occurs during a Subtest and YES is selected for Error Stop, the following message displays: [HALT OPERATION] 1. Test end 2. Continue 3. Retry * Select 1, 2, or 3 The three selections have the following functions: 1: Terminates the test program and exits to the subtest menu. 2: Continues the test from the error. 3: Restarts the test from the beginning. Use the arrow keys to move the cursor to the desired option and press Enter. 3.21.
PAGE 166
Replacement Procedures Chapter 4 Replacement Procedures Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-i
PAGE 167
Replacement Procedures Chapter 4 4.1 Contents Overview.................................................................................................................... 4-1 Safety Precautions ................................................................................................ 4-2 Before You Begin ................................................................................................ 4-3 Disassembly Procedure...........................................................................
PAGE 168
Replacement Procedures Figures Figure 4-1 Remove the battery pack................................................................................. 4-8 Figure 4-2-1 Install the battery pack.................................................................................... 4-9 Figure 4-3 Remove a PC card......................................................................................... 4-10 Figure 4-2-1 Insert a PC card................................................................................
PAGE 169
Replacement Procedures Figure 4-22 Remove the USB Board ............................................................................... 4-47 Figure 4-23 Disconnect the power cable ......................................................................... 4-48 Figure 4-24 Remove the system board ............................................................................ 4-51 Figure 4-25 Remove the CPU heat sink ..........................................................................
PAGE 170
Replacement Procedures 4 2 4.1 Overview This chapter describes the procedure for removing and replacing the field replaceable units (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to which other FRUs must be removed before a particular FRU can be removed. The numbers in the chart indicate the relevant section numbers in this manual. In all cases when removing an FRU, the battery pack must also be removed.
PAGE 171
Replacement Procedures Safety Precautions Please read the following safety instructions before disassembling the computer and always follow the instructions while working on the computer. DANGER: 1. In the case of the battery, always use authentic parts or equivalent parts approved by Toshiba. Other batteries may have different specifications that are incompatible with the computer and may result in fire or explosion. Due to the risk of alkali fluid leaks, never attempt to heat or disassemble the battery.
PAGE 172
Replacement Procedures Before You Begin Take note of the following points before starting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “4.2.1 Battery Pack”. 1. Do not disassemble the computer unless it is operating abnormally. 2. Use the designated tools. 3. Ensure that the environment for working on and storing parts does not contain any of the following.
PAGE 173
Replacement Procedures Disassembly Procedure Three main types of cable connector are used. • Pressure plate connector • Spring connector • Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on the connector and pull the cable out from the connector. When reconnecting a cable to a pressure plate connector, lift up the pressure plate to a suitable height and insert the cable into the connector.
PAGE 174
Replacement Procedures Assembly Procedure After the computer has been disassembled and the part that caused the fault has been repaired or replaced, the computer must be reassembled. Take note of the following general points when assembling the computer. • Take your time and follow the instructions carefully. Hurrying the assembly work will only introduce new problems. • Check that all cables and connectors are securely connected.
PAGE 175
Replacement Procedures Screw Tightening Torque Use the following torque when tightening screws. CAUTION: Overtightening may damage screws or parts. Undertightening may allow screws to loosen (and possibly fall out) causing a short circuit or other damage. NOTE: To tighten screws quickly and accurately, an electric screwdriver is recommended. • M2 (2mm) 0.167 N·m (1.7 kgf·cm) • M2.5 (2.5mm) 0.245 N·m(2.5 kgf·cm) • M2.5 (2.5mm) 0.392 N·m(4.0 kgf·cm) for Hinge support • M3.0 (3mm) 0.245 N･m (2.
PAGE 176
Replacement Procedures Screw Notation To make maintenance of the computer easier, markings of the kinds of the screws including the types and lengths are indicated on the computer body. Format: Screw shape + Screw length (mm) Screw shape B: Bind screw F: Thin head screw S: Super thin head screw T: Tapping screw U: Other screws (Unique screws: pan head, stud, etc.
PAGE 177
Replacement Procedures 4.2 Battery pack Removing the battery pack The following describes the procedure for removing the battery pack (See Figure 4-1). CAUTION: Take care not to short circuit the terminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, twist, or bend the battery pack. 1. Turn off the power of the computer. 2. Disconnect the AC adapter and all external devices from the computer. 3. Turn the computer upside down. 4.
PAGE 178
Replacement Procedures NOTE: Dispose of the used battery pack in accordance with the laws and ordinances of your local authority. Installing the battery pack The following describes the procedure for installing the battery pack (See Figure 4-1). CAUTION: There is a danger that the lithium ion battery pack may explode if not fitted, operated, handled, or disposed correctly. Dispose always the used battery pack in accordance with the laws and ordinances of your local authority.
PAGE 179
Replacement Procedures 4.3 PC card Removing a PC card The following describes the procedure for removing a PC card (See Figure 4-2-1). CAUTION: Insert or remove a PC card in accordance with any instructions in a PC card manual or the manuals of the computer system you are using. 1. Push the PC card. It will pop out PCMCIA Card when you release it. And NEW Card same as PC card. Then press the card once more to eject a card. 2. Grasp one of PC card and remove it.
PAGE 180
Replacement Procedures Installing a PC card The following describes the procedure for inserting a PC card (See Figure 4-2-2). 1. Make sure the PC card does not stick out. 2. Insert a PC card and press it until it is securely connected.
PAGE 181
Replacement Procedures 4.4 HDD Removing a MAIN HDD-H9.5mm / HDD-H12.5mm The following describes the procedure for removing the main HDD (See Figure 4-3 to 4-4). CAUTION: Take care not to press on the top or bottom of a HDD. Pressure may cause data loss or damage to the device. 1. Turn the computer upside down. 2. Remove the following screws securing a HDD slot cover and remove a HDD slot cover. • M2.5×4.0B FLAT BIND screw x2 3. Remove the following screws securing the HDD assembly. • M2.5×5.
PAGE 182
Replacement Procedures MAIN HDD Figure 4-4 Turn the compute upside down Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-13
PAGE 183
Replacement Procedures CAUTION: When a HDD is installed, they are installed in the position as the following figure. SCREW PULL TAB SCREW M2.
PAGE 184
Replacement Procedures 5. Remove the following screws securing the HDD holder and remove the HDD holder. • M3.0×3.0B FLAT BIND screw SCREW M3*3—4pcs HDD H=9.5mm / H=12.
PAGE 185
Replacement Procedures Installing MAIN HDD-H9.5mm / HDD-H12.5mm The following describes the procedure for installing the main HDD (See Figure 4-3 to 4-4). 1. Install a HDD to the HDD holder and secure it with the following screws. • M3.0×3.5F FLAT BIND screw x4 NOTE: Although they are 3mm head screws, screw torque must be set in 2.5kg-cm for four screws securing the HDD holder. 2. Insert the HDD assembly into the HDD slot and connect it carefully to the MAIN HDD on the system board. 3.
PAGE 186
Replacement Procedures 4.5 HDD Removing second HDD-H9.5mm / HDD-H12.5mm The following describes the procedure for removing the second HDD (See Figure 4-3 to 4-4). CAUTION: Take care not to press on the top or bottom of a HDD. Pressure may cause data loss or damage to the device. 4. Turn the computer upside down. 5. Remove the following screws securing a HDD slot cover and remove a HDD slot cover. • M2.5×4.0B FLAT BIND screw x2 6. Remove the following screws securing the HDD assembly. • M2.5×5.
PAGE 187
Replacement Procedures SECOND HDD Figure 4-4-1 Turn the computer upside down CAUTION: When a HDD is installed, they are installed in the position as the following figure.
PAGE 188
Replacement Procedures SCREW SCREW M2.
PAGE 189
Replacement Procedures 8. Remove the following screws securing the HDD holder and remove the HDD holder. • M3.0×3.0B FLAT BIND screw x4 SCREW M3*3—4pcs HDD H=9.5mm / H=12.
PAGE 190
Replacement Procedures Installing Second HDD-H9.5mm / HDD-H12.5mm The following describes the procedure for installing a HDD (See Figure 4-3 to 4-4). 9. Install a HDD to the HDD holder and secure it with the following screws. • M3.0×3.5F FLAT BIND screw x4 NOTE: Although they are 3mm head screws, screw torque must be set in 2.5kg-cm for four screws securing the HDD holder. 10. Insert the HDD assembly into the HDD slot and connect it carefully to the MAIN HDD on the system board. 11.
PAGE 191
Replacement Procedures 4.6 Wireless LAN card Removing a Wireless LAN card The following describes the procedure for removing a Wireless LAN card (See Figure 4-5). 1. Remove the following screw of wireless cover securing wireless LAN card cover and remove it. And remove screw of wireless board • 2.5.0 x 4.0B BIND screw x3 2. Disconnect the wireless LAN antenna cable from the connectors on a wireless LAN card. 3.
PAGE 192
Replacement Procedures RAM Door 3 screws Wireless LAN with 2 screws Wireless LAN antenna cable CN30 Wireless LAN card Figure 4-5 Remove a wireless LAN card Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-23
PAGE 193
Replacement Procedures Installing a Wireless LAN car The following describes the procedure for installing a Wireless LAN card (See Figure 4-5). 1. Insert a wireless LAN card terminals slantwise into the connector on the computer and press a wireless LAN card and lock the secure screws. 2. Connect the wireless LAN antenna cables to the terminals on a wireless LAN card. 3. Install the wireless LAN card cover and secure it with the following screw.
PAGE 194
Replacement Procedures 4.7 Memory module CAUTION: The power of the computer must be turned off when you remove a memory module. Removing a memory module with the power on risks damaging the module or the computer itself. Do not touch memory module terminals. Any dirt on the terminals may cause memory access problems. Never press hard or bend a memory module. Removing a memory module To remove a memory module, confirm that the computer is in boot mode.
PAGE 195
Replacement Procedures RAM Door 3 screw Figure 4-6 Remove memory slot cover Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-26
PAGE 196
Replacement Procedures Figure 4-6-1 Remove a memory module Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-27
PAGE 197
Replacement Procedures Installing a memory module To install a memory module, confirm that the computer is in boot mode. Then perform the following procedure (See Figure 4-7). 1. Insert a memory module into the connector of the computer slantwise (terminal side first) and press it to connect firmly. CAUTION: The power must be turned off when you insert a memory module. Inserting a memory module with the power on might damage the module or the computer itself. Never press hard or bend a memory module. 2.
PAGE 198
Replacement Procedures 4.8 Keyboard Removing the keyboard The following describes the procedure for removing the keyboard (See Figure 4-8 to 4-9). CAUTION: As the keycap may fall out, when handling the keyboard always hold it by the frame and do not touch the keycap. 1. Turn the computer upside down 2. Loose the screw securing KBD Holder. M2.5x3.0B Flat BIND screws x3 3. Upside down the computer. 4. Open the display. 5. Remove KBD holder.
PAGE 199
Replacement Procedures Battery KB Holder 3 screw Figure 4-8 Remove screws for KB Holder Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-30
PAGE 200
Replacement Procedures Keyboard 2screw KB holder Keyboard Figure 4-9 Remove the keyboard/KB Holder Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-31
PAGE 201
Replacement Procedures Installing the keyboard The following describes the procedure for installing the keyboard (See Figure 4-8 to 4-9). 1. Turn the keyboard upside down and place it on the palm rest as its face down. Connect the keyboard flexible cable to the connector on the system board. 2. Slide and set the speaker cover assembly and secure it with the following screw. • M2.5×5.0B FLAT BIND screw x2 3. Install the keyboard brace by pressing it from the topside.
PAGE 202
Replacement Procedures 4.9 Optical disk drive NOTE: Do not apply excessive force to the top of an optical disk drive. Do not touch the shaded portion of the figure below, when the drive is removed or installed. Removing an optical disk drive The following describes the procedure for removing an optical disk drive (See Figure 411and 4-12). 1. Remove Keyboard and next remove the following screws securing an optical disk drive. • M2.5×5.0B FLAT BIND screw x1 2.
PAGE 203
Replacement Procedures ODD BKT ODD BKT screw Figure 4-11 Disassemble the side bracket Installing an optical disk drive The following describes the procedure for installing an optical disk drive (See Figure 4-11 and 4-12). 1. Attach the ODD bracket to an optical disk drive and secure it with the following screws. • M2.0×3.0 Flat BIND screw x3 2. Insert an optical disk drive assembly into the slot and connect it to the connector CN26 on the system board. 3. Secure the ODD drive with the following screw.
PAGE 204
Replacement Procedures 4 4.10 Display assembly Removing the display assembly The following describes the procedure for removing the display assembly (See Figure 4-13 to 4-17). 1. Close the display and turn the computer upside down. 2. Open the RAM Door and remove antenna cable Connector. M2.5x4.
PAGE 205
Replacement Procedures 3. Remove Battery and disassembly k/b holder and keyboard screw. (please refer figure 4-8,figure4-9). KB holder screw * 3 M2.5x3.0 FLAT BIND (Locktight) KB screw * 2 M2.5x5.
PAGE 206
Replacement Procedures 4. Disassembly TOP ASSY M2.5x5.0 M2.5x8.0 M2.5x3.0 M2.5x8.0 M2.5x5.0 M2.5x6.5 M2.5x6.5 M2.5x3.0 M2.5x8.0 M2.5x5.0 Figure 4-13 Remove the screws (from bottom side) M2.5x5.
PAGE 207
Replacement Procedures 5. Pull out the wireless LAN antenna and LCD cables from the guide Antenna cable LCD cable Figure 4-15 Remove the Wireless Antenna and LCD cable Opening the display to 135degree, and remove the hinge screw. M2.5×6.5 FLAT BIND screw x6 (Locktight) M2.5x6.5 M2.5x6.5 ..
PAGE 208
Replacement Procedures Figure 4-16 Remove the hinge screws Satellite P300 and Satellite Pro P300 Maintenance Manual (960-Q08) 4-39
PAGE 209
Replacement Procedures 6. Pulling out the pole of hinge from the hole of hinge assembly, remove the display assembly from the base assembly. Display assembly Base assembly .
PAGE 210
Replacement Procedures Installing the display assembly The following describes the procedure for installing the display assembly (See Figure 4-13 to 4-17). 1. Inserting the pole of hinge to the hole of hinge assembly, set the display assembly on the base assembly. 2. Secure the hinges with the following screws secure the display mask with the following screws and stick the mask seal on them. • M2.5×6.
PAGE 211
Replacement Procedures 4.11 Cover assembly Removing the cover assembly The following describes the procedure for removing the cover assembly (See Figure 4-19 to 4-21). 1. Turn over the computer. 2. Remove the following screws securing the cover assembly from the back and bottom of computer. M2.5x5.0 • M2.0×5.0 FLAT BIND screw Back x4 • M2.5×6.5 FLAT BIND screw Back x11 • M2.5×8.0 FLAT BIND screw Back x4 • M2.0×3.0 FLAT BIND screw Back x5 M2.5x8.0 M2.5x3.0 M2.5x8.0 M2.5x5.0 M2.5x6.
PAGE 212
Replacement Procedures 3. Disconnect the touch pad flat cable/Fingerprint cable from the connector on the system board.
PAGE 213
Replacement Procedures 4. Remove the following screws securing the cover assembly from the front of computer. Pull up and remove the cover assembly from the base assembly. M2.0×5.0 FLAT BIND screw Front x3 KB Holder Keyboard M2.5x5.
PAGE 214
Replacement Procedures Installing the cover assembly The following describes the procedure for installing the cover assembly (See Figure 4-19 to 4-21). 1. Install the cover assembly to the base assembly. NOTE: Be careful not to catch the cables between cover assembly and base assembly. 2. Connect the touch pad flat cable to the connector on the system board. 3. Secure the cover assembly with the following screws from the back and bottom of computer. • M2.0×5.0 FLAT BIND screw Back x4 • M2.5×6.
PAGE 215
Replacement Procedures 4.12 Touch pad Removing the touch pad The following describes the procedure for removing the touch pad (See Figure 4-22). 1. Peel off the glass tape and disconnect the touch pad flat cable, finger print cable from the connector on the touch pad. 2. Remove the following screws securing the touch pad plate. • M2.0×3.0B SUPER THIN HEAD screw x6 3. Remove the touch pad board and touch pad plate. 4. Peel off and remove the touch pad from the cover assembly.
PAGE 216
Replacement Procedures Installing the touch pad The following describes the procedure for installing the touch pad (See Figure 4-22). 1. Peel off the separator covering on the sensor portion of a new touch pad. NOTE: Do not reuse the touch pad so that it can not be used after peeling off from the computer. Be sure to stick a new touch pad. When sticking the touch pad, be careful not to get the bubbles under the touch pad. 2. Stick and install the touch pad on the cover assembly. 3.
PAGE 217
Replacement Procedures 4.13 USB Board The following describes for removing the cover assembly (See Figure 4-23). Removing the USB board 1. Pull out the USB cable, Modem cable, from USB board connector. 2. Loose the below screws and then incline pull out USB board. z M2.0x5.0 FLAT BIND screw x2 Modem cable USB cable Figure 4-22 Remove the USB Board Installing the USB board 1. Insert the usb board into base case and connect USB board cable, Modem cable 2. Fix the below screws M2.0x5.
PAGE 218
Replacement Procedures 4.14 System board CAUTION: 1. when handling the system board, always hold by the edges. Do not touch the printed circuit face. 2. if replacing with a new system board, execute the subtest01 Initial configuration in section 3.3 “Setting of the hardware configuration”. Also update with the latest BIOS as described in Appendix G “BIOS Rewrite Procedures” and with the latest EC/KBC as described in Appendix H “EC/KBC Rewrite Procedures”.
PAGE 219
Replacement Procedures 3. Remove the following screws securing the system board and remove the system board. (See Figure 4-26) • M2.5×5.
PAGE 220
Replacement Procedures Installing the system board The following describes the procedure for installing the system board (See Figure 4-26). 1. Secure the system board with the following screws. • M2.5×5.0 BIND screw x4 2. Connect the speaker cable, USB cable, FM CABLE, MDC CABLE and BLUETOOTH CABLE to the connector on the system board. 3.
PAGE 221
Replacement Procedures 4.15 CPU Removing the CPU heat sink The following describes the procedure for removing the CPU heat sink (See Figure 4-27). 1. Disconnect the Heat sink cable from the connector on the system board 2. Remove the following screws securing the heat sink holder along 1 to 6. • M2.5×5.0 BIND screw x8 NOTE: When removing the heat sink holder, be sure to remove the screws in the reverse order of the number marked on the holder. 3. Remove the CPU heat sink.
PAGE 222
Replacement Procedures 4. Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the counterclockwise with a flat-blade screwdriver. 5. Remove the CPU. Figure 4-26 Remove the CPU Installing the CPU The following describes the procedure for installing the CPU (See Figure 4-27 to 4-28). 1. Check that the mark of cam is in the unlocking position. 2. Attach the CPU to the correct position in the CPU socket. 3.
PAGE 223
Replacement Procedures Figure 4-27 Apply silicon grease 6. Install the CPU heat sink and heat sink holder and secure them with the following screws along 1 to 6. M2.5×5.0 BIND screw x8 7. Connect the Heat sink cable to the connector on the system board NOTE: When securing the heat sink holder, be sure to secure the screws in the order of the number marked on the holder.
PAGE 224
Replacement Procedures 4.16 LCD unit / FL inverter CAUTION: When replacing a LCD, it is required that SVP parameter is set. Update with the latest EC/KBC as described in Appendix H “EC/KBC Rewrite Procedures”. Removing the LCD unit / FL inverter The following describes the procedure for removing the LCD unit and FL inverter (See Figure 4-30 to 4-33) Remove Screw rubber cover X8 1. Remove the following screws securing the display mask M2.5×5.0 M2.5×4.0 BIND screw X4 BIND screw X4 2.
PAGE 225
Replacement Procedures 3. Pull out one insulator and peel off the other one adhered to the FL inverter. 4. Disconnect the LCD harnesses from the connectors CN1 on the FL inverter. 5. Disconnect the HV harnesses from the connectors CN2 on the FL inverter. 6. Remove the FL inverter while peeling off the double-sided tape.
PAGE 226
Replacement Procedures 7. Remove the following screws securing the LCD unit. • M2.5x5.0 BINK HEAD screw x4 8. With the bottom edge of the LCD unit on the display cover, lift only the top edge of the LCD unit. After peeling off the CONDUTIVE tape, disconnect the LCD harness from the connector on the back of the LCD. 9. Remove the LCD unit.
PAGE 227
Replacement Procedures 10. Remove the following screws securing the LCD support (LCD unit side) and remove the LCD supports and LCD top bracket from the LCD unit. • M2.0x2.
PAGE 228
Replacement Procedures Installing the LCD unit/FL Inverter The following describes the procedure for installing the LCD unit and FL inverter (See Figure 4-31 to 4-34). 1. Install the LCD supports (LCD unit side) and LCD top bracket to the LCD and secure them with the following screws. • M2.0×2.5 BINK screw x6 2. Stand the LCD unit on the display cover and connect the LCD harness to the connector on the back of LCD. 3. Stick the conductive tape on the connector of LCD harness. 4.
PAGE 229
Replacement Procedures 4.17 Application for Grease (Denka FCR-AS)/Thermal pad on North Bridge, VGA,V-RAM I. For Satellite P300, Satellite Pro P300, EQUIUM P300, SATEGO P300(Intel without VGA Board) use Thermal pad on North Bridge TSB PN RW PN Used on A000032180 JXBL5016010 N-BRIDGE THERMAL PAD BL5(JXBL5016,3A) Figure 4-32 Thermal pad on North Bridge II.
PAGE 230
Replacement Procedures Figure 4-33 Apply silicon grease for North Bridge 4. Thermal pad used on VGA, VRAM1, VRAM2, VRAM3, VRAM4.
PAGE 231
Replacement Procedures III. For Satellite P300D, Satellite Pro P300D, EQUIUM P300D, SATEGO P300D (AMD without VGA Board) use the thermal pad only on North Bridge. TSB PN A000037540 RW PN JXBD3027010 Used on UMA NB PAD FSL-BS BD3A(JXBD3027,3A) Figure 4-37 Thermal pad position IV.
PAGE 232
Replacement Procedures Figure 4-38 Thermal pad & VRAM position NOTE: When applying for grease on North Bridge, one syringe*1cc can cover about seven repairs. Thermal pad is fixed for each one, no need special applicator and can re-use.
PAGE 233
Appendices Appendix Contents Appendix A Handling the LCD Module......................................................................... A-1 Appendix B Board Layout............................................................................................... B-1 B.1 System Board ................................................................................................ B-1 B.2 MMB Board .................................................................................................. B-5 B.
PAGE 234
C.2 CN5 INTMIC Connector1 ............................................................................... 2 C.3 CN7 Main stream MMB Connector ................................................................ 3 C.4 CN8 Power board Connector ........................................................................ 3 C.5 CN9 Keyboard Side Connector .................................................................... 3 C.6 CN11 T/P Connector..............................................................
PAGE 235
C.36 CN39 INT MIC Connector……………………………… ………… C.37 CN40 Headphone Jack……………………………………………… … 31 C.38 CN41 SYSTEM MIC Jack………………………………… ………… 31 C.39 CN42 FM Connector……………………………………… …………… 31 C.40 CN43 30 MDC Connector……………………………………… …………… 32 Appendix D Display Codes .............................................................................................. D-1 D.1 Display Codes ...............................................................................................
PAGE 236
E.23 Swedish (SD) Keyboard....................................................................... ....E-12 E.24 Belgian ( BE ) Keyboard............................................................................E-12 E.25 Yugoslavian (YU) Keyboard.......................................................................E-13 E.26 Norwegian(NW)Keyboard........................................................................ E-13 E.27 Scandinavian (ND) Keyboard..............................................
PAGE 237
Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained. 2.
PAGE 238
Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it.
PAGE 239
Handling the LCD Module 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.
PAGE 240
Handling the LCD Module 7. Do not expose the module directly to sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
PAGE 241
Handling the LCD Module 10. If you transport the module, do not use packing material which contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization.
PAGE 242
Appendix B Appendix B Board Layout B.
PAGE 243
Board Layout (26) (20) (21) (22) (23) (24) (25) (27) (53) (52) (51) (28) (50) (29) (49) (30) (48) (31) (47) (32) (46) (45) (33) (44) (43) (42) (41) (40) (39) (38) (37) (36) (35) (34) Figure B-2 System board layout (Back) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-2
PAGE 244
Board Layout Table B-1 System board ICs and connectors (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) Location CN4 CN5 CN8 CN6 CN7 CN9/CN10 CN11 CN13 CN42 CN16 CN14 CN17 U17 (14) U20 (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25) (26) (27) (28) (29) (30) (31) (32) (33) MR4 SW4 LED6 LED5 CN15 CN20 U26 U27 U25 U24 CN27 CN19 CN18 CN22 CN25 CN28 CN31 CN35 CN38 (34) U35 (35) (36) (37) (38) LED8 CN32 U41 CN43 Function M/B to panel connector Internal MIC cable connector M/B to
PAGE 245
Board Layout (39) (40) (41) (42) (43) (44) (45) (46) (47) (48) (49) (50) (51) (52) (53) CN33 CN30 CN41 CN40 VR4 CN39 U38 CN37 CN34 U32 CN26 CN23 CN24 PCN4 CN21 Card Reader connector HD DVD Decoder Module Slot External MIC Jack Headphone and SPDIF Combo Jack Volume Regulator Internal MIC cable connector Azalia Audio Codec Conexant CX20561-12Z RTC Battery connector 1st SATA connector South Bridge PATA ODD connector DDR SO-DIMM Slot B DDR SO-DIMM Slot A ACIN cable connector WLAN Module Slot Satellite P300
PAGE 246
Board Layout B.
PAGE 247
Board Layout B.
PAGE 248
Board Layout B.
PAGE 249
Board Layout Figure B-6 USB with RJ11 board layout (back) Table B-4 USB with RJ11 board connectors (01) (02) (03) (04) (05) Location CN2 CN3 CN1 CN4 CN5 Function Connect to Modem module Connect to M/B USB connector RJ11 connector USB connector USB connector Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-8
PAGE 250
Board Layout B.
PAGE 251
Board Layout Figure B-8 USB with FM board layout (back) Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-10
PAGE 252
Board Layout Table B-5 USB with FM board connectors (01) (02) (03) (04) (05) Location CN7 CN3 CN8 CN4 CN5 Function Connect to M/B FM connector Connect to M/B USB connector FM Jack USB connector USB connector Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) B-11
PAGE 253
Board Layout B.
PAGE 254
Board Layout Table B-6 Touch pad board connectors (01) (02) (03) (04) Location SW1 SW3 SW4 SW2 Function Mouse Button Left key Mouse Button Left key Mouse Button Right key Mouse Button Right key (05) CN2 TP board to FP board connector (06) CN3 TP board to FP board connector (07) (08) (09) (10) (11) CN1 TP board to M/B USB signal connector CN4 CN5 LED4 LED1 TP board to M/B USB signal connector TP Board to TP module connector ACIN LED Power and Suspend LED (12) LED2 Battery Charge LED (13)
PAGE 255
Board Layout B.
PAGE 256
Board Layout B.
PAGE 257
Board Layout B.
PAGE 258
Pin Assignment Appendix C Pin Assignment CN4 LCD TYPE CONNECTOR CONN SMD WAFER 40P 2R MS(P1.0,H3.9) PIN No. Signal name I/O PIN No.
PAGE 259
Pin Assignment 39 TXLOUT2- I/O 40 TXUOUT2- I/O 41 GND --- 42 GND --- CN5 INTMIC Connector1 CONN SMD HEADER 2P 1R MR(P1.25,H1.9) PIN No. 1 Signal name MIC_GND I/O --- PIN No. Signal name I/O 2 Analog MIC --- CN6 Low cost MMB Connector CONN SMD FPC 10P 1R FR(P1.0,H1.5) PIN No. Signal name I/O PIN No.
PAGE 260
Pin Assignment CONN SMD FPC 6P 1R FR(P1.0,H1.5) PIN No. Signal name I/O PIN No. Signal name I/O 1 +3VPCU --- 2 +5VPCU --- 3 KEY_INT I 4 GND --- 5 3ND_MBDATA I/O 6 3ND_MBCLK I/O CN8 Power board Connector CONN SMD FFC 4P 1R FR (P1.0,H1.5) PIN No. Signal name I/O PIN No. Signal name I/O 1 +5VPCU --- 2 NBSWON# I 3 PWRLED# I 4 GND --- CN9 Keyboard Side Connector CONN SMD FFC 34P,1R,FR(P0.8,H2.0) PIN No. Signal name I/O PIN No.
PAGE 261
Pin Assignment 15 MY7 I 16 MY13 I 17 MY8 I 18 MY9 I 19 MY10 I 20 MY11 I 21 MY12 I 22 MY15 I 23 MX7 I 24 MX2 I 25 MX3 I 26 MX4 I 27 MX0 I 28 MX5 I 29 MX6 I 30 MX1 I 31 K_LED_P I 32 CAPSLED I 33 FN_F10 I 34 NUMLED I CN11 T/P Connector CONN SMD FFC 14P 1R FR(P0.5,H1.5) PIN No. Signal name I/O PIN No.
PAGE 262
Pin Assignment PIN No. Signal name I/O PIN No. Signal name I/O 1 FELICA_POWER --- 2 USBP5-_C I/O 3 USBP5+_C I/O 4 GND --- 5 NC --- 6 FELICA_DE --- CN13 Finger Printer CONNECTOR CONN SMD HEADER 4P 1R MR(P1.25,H1.9) PIN No. Signal name I/O PIN No. Signal name I/O 1 FINGER_POWER --- 2 USBP4-_C I/O 3 USBP4+_C 4 GND --- I/O CN14 BLUETOOTH MODULE CONNECTOR CONN SMD HEADER 10P 1R MR(P1.25,H1.9) PIN No. Signal name I/O PIN No.
PAGE 263
Pin Assignment PIN No. Signal name I/O PIN No. Signal name I/O 1 GND O 2 USBP6-_R I/O 3 USBP6+_R I/O 4 CPUSB# I 5 T84 --- --- T89 --- 7 NEW_SMCLK I/O 8 NEW_SMDATA I/O 9 +NEW_1.5V --- 10 +NEW_1.
PAGE 264
Pin Assignment PIN No. Signal name I/O PIN No. Signal name I/O 1 INSPKL-N --- 2 INSPKL+N --- 3 INSPKR-N --- 4 INSPKR+N --- CN18 CRT PORT Connector CONN DIP D-SUB 15P 2R FR(H12.5,P0.76) PIN No. Signal name I/O PIN No.
PAGE 265
Pin Assignment PIN No. Signal name I/O PIN No. Signal name I/O 1 MBAT+ --- 2 MBAT+ --- 3 ID_L O 4 B/I O 5 TEMP_MBAT --- 6 MBDATA I/O 7 MBCLK I/O 8 GND --- 9 GND --- CN21 MINI-Card I (WLAN) Connector CONN SMD HEADER,52P,2R,MS(P0.8,H9) PIN No. Signal name I/O PIN No. Signal name I/O 1 WLAN_WAKE# O 2 +3V_WL_VDD --- 3 WCS_DATR --- 4 GND --- 5 WCS_CLKR --- 6 +1.
PAGE 266
Pin Assignment 29 GND --- 30 WL_SMCLK_WLA N I/O 31 GPP_TX1N_WLAN I 32 WL_SMDATA_WL AN I/O 33 GPP_TX1P_WLAN I 34 GND --- 35 GND --- 36 USBP3-_C I/O 37 NC --- 38 USBP3+_C I/O 39 +3V_WL_VDD --- 40 GND --- 41 +3V_WL_VDD --- 42 WiMAX_LED#_A --- 43 GND --- 44 NC --- 45 NC --- 46 NC --- 47 NC --- 48 +1.5V --- 49 NC --- 50 GND --- 51 NC O 52 +3V_WL_VDD --- CN22 TVOUT Connector CONN DIP MINI-DIN 4P FR(P1.0,H10.5) PIN No.
PAGE 267
Pin Assignment PIN No. Signal name I/O PIN No.
PAGE 268
Pin Assignment 47 GND --- 48 GND --- 49 M_B_DQS#2 I/O 50 T59 --- 51 M_B_DQS2 I/O 52 M_B_DM2 I 53 GND --- 54 GND --- 55 M_B_DQ19 I/O 56 M_B_DQ18 I/O 57 M_B_DQ23 I/O 58 M_B_DQ22 I/O 59 GND --- 60 GND --- 61 M_B_DQ29 I/O 62 M_B_DQ24 I/O 63 M_B_DQ28 I/O 64 M_B_DQ25 I/O 65 GND --- 66 GND --- 67 M_B_DM3 I 68 M_B_DQS#3 I/O 69 T57 --- 70 M_B_DQS3 I/O 71 GND --- 72 GND --- 73 M_B_DQ26 I/O 74 M_B_DQ30 I/O 75 M_B_DQ27 I/O 76 M_B_D
PAGE 269
Pin Assignment 95 +1.8VSUS --- 96 +1.8VSUS --- 97 M_B_A5 I/O 98 M_B_A4 I/O 99 M_B_A3 I/O 100 M_B_A2 I/O 101 M_B_A1 I/O 102 M_B_A0 I/O 103 +1.8VSUS --- 104 +1.8VSUS --- 105 M_B_A10 I/O 106 M_B_BS#1 I 107 M_B_BS#0 I 108 M_B_RAS# I 109 M_B_WE# I 110 M_B_CS#0 I 111 +1.8VSUS --- 112 +1.8VSUS --- 113 M_B_CAS# I 114 M_ODT2 I 115 M_B_CS#1 I 116 M_B_A13 I/O 117 +1.8VSUS --- 118 +1.
PAGE 270
Pin Assignment 143 M_B_DQ41 I/O 144 GND --- 145 GND --- 146 M_B_DQS#5 I/O 147 M_B_DM5 I 148 M_B_DQS5 I/O 149 GND --- 150 GND --- 151 M_B_DQ46 I/O 152 M_B_DQ47 I/O 153 M_B_DQ43 I/O 154 M_B_DQ42 I/O 155 GND --- 156 GND --- 157 M_B_DQ53 I/O 158 M_B_DQ48 I/O 159 M_B_DQ49 I/O 160 M_B_DQ52 I/O 161 GND --- 162 GND --- 163 T29 --- 164 M_CLKOUT4 I 165 GND --- 166 M_CLKOUT4# I 167 M_B_DQS#6 I/O 168 GND --- 169 M_B_DQS6 I/O 170 M_B_DM6
PAGE 271
Pin Assignment 191 M_B_DQ59 I/O 192 M_B_DQ63 I/O 193 GND --- 194 M_B_DQ58 I/O 195 DDRDAT_SMB I/O 196 GND --- 197 DDRCLK_SMB I/O 198 SA0_B --- 199 +3V --- 200 SA1_B --- CN24 DDRII SODIMM Connector2 DDR2 SO-DIMM(200P,H5.6,RVS) PIN No. Signal name I/O PIN No.
PAGE 272
Pin Assignment 31 M_A_DQS1 I/O 32 M_CLKOUT0# I 33 GND --- 34 GND --- 35 M_A_DQ10 I/O 36 M_A_DQ15 I/O 37 M_A_DQ14 I/O 38 M_A_DQ11 I/O 39 GND --- 40 GND --- 41 GND --- 42 GND --- 43 M_A_DQ21 I/O 44 M_A_DQ20 I/O 45 M_A_DQ17 I/O 46 M_A_DQ19 I/O 47 GND --- 48 GND --- 49 M_A_DQS#2 I/O 50 T58 --- 51 M_A_DQS2 I/O 52 M_A_DM2 I 53 GND --- 54 GND --- 55 M_A_DQ23 I/O 56 M_A_DQ22 I/O 57 M_A_DQ18 I/O 58 M_A_DQ16 I/O 59 GND --- 60 GND
PAGE 273
Pin Assignment 79 M_CKE0 I 80 M_CKE1 I 81 +1.8VSUS --- 82 +1.8VSUS --- 83 M_A_CS#2 --- 84 M_A_A15 --- 85 M_A_BS#2 I 86 M_A_A14 --- 87 +1.8VSUS --- 88 +1.8VSUS --- 89 M_A_A12 I/O 90 M_A_A11 I/O 91 M_A_A9 I/O 92 M_A_A7 I/O 93 M_A_A8 I/O 94 M_A_A6 I/O 95 +1.8VSUS --- 96 +1.8VSUS --- 97 M_A_A5 I/O 98 M_A_A4 I/O 99 M_A_A3 I/O 100 M_A_A2 I/O 101 M_A_A1 I/O 102 M_A_A0 I/O 103 +1.8VSUS --- 104 +1.
PAGE 274
Pin Assignment 127 GND --- 128 GND --- 129 M_A_DQS#4 I/O 130 M_A_DM4 I 131 M_A_DQS4 I/O 132 GND --- 133 GND --- 134 M_A_DQ34 I/O 135 M_A_DQ37 I/O 136 M_A_DQ39 I/O 137 M_A_DQ35 I/O 138 GND --- 139 GND --- 140 M_A_DQ44 I/O 141 M_A_DQ40 I/O 142 M_A_DQ45 I/O 143 M_A_DQ41 I/O 144 GND --- 145 GND --- 146 M_A_DQS#5 I/O 147 M_A_DM5 I 148 M_A_DQS5 I/O 149 GND --- 150 GND --- 151 M_A_DQ42 I/O 152 M_A_DQ43 I/O 153 M_A_DQ46 I/O 154 M_A_D
PAGE 275
Pin Assignment 175 M_A_DQ51 I/O 176 M_A_DQ52 I/O 177 GND --- 178 GND --- 179 M_A_DQ56 I/O 180 M_A_DQ57 I/O 181 M_A_DQ60 I/O 182 M_A_DQ61 I/O 183 GND --- 184 GND --- 185 M_A_DM7 I 186 M_A_DQS#7 I/O 187 GND --- 188 M_A_DQS7 I/O 189 M_A_DQ59 I/O 190 GND --- 191 M_A_DQ58 I/O 192 M_A_DQ63 I/O 193 GND --- 194 M_A_DQ62 I/O 195 DDRDAT_SMB I/O 196 GND --- 197 DDRCLK_SMB I/O 198 SA0_A --- 199 +3V --- 200 SA1_A --- CN25 HDMI Connector CONN
PAGE 276
Pin Assignment 7 HDMITX0P_C O 8 GND --- 9 HDMITX0N_C O 10 HDMICLK+_C O 11 GND --- 12 HDMICLK-_C O 13 CEC I/O 14 NC --- 15 HDMI_SCL O 16 HDMI_SDA O 17 GND --- 18 DDC5V --- 19 HDMI_HPD I --- CN26 ODD CONNECTOR CONN DIP HOUSING 50P 2R FR(P0.8,H4.1) PIN No. Signal name I/O PIN No.
PAGE 277
Pin Assignment 25 PDIOW# I 26 GND --- 27 PDIORDY O 28 PDDACK# I 29 IRQ14 O 30 NC --- 31 PDA1 I/O 32 DIAG# --- 33 PDA0 I/O 34 PDA2 I/O 35 PDCS1# I 36 PDCS3# O 37 ODD_LED# O 38 +5V --- 39 +5V --- 40 +5V --- 41 +5V --- 42 +5V --- 43 GND --- 44 GND --- 45 GND --- 46 GND --- 47 GND --- 48 GND --- 49 NC --- 50 NC --- CN27 MXM Connector CONN SMD HOUSING 200P FS(P5.15,H8.65) PIN No. Signal name I/O PIN No.
PAGE 278
Pin Assignment 9 PEG_RXP14 I 10 PEG_TXP14 O 11 GND --- 12 GND --- 13 PEG_RXN13 I 14 PEG_TXN13 O 15 PEG_RXP13 I 16 PEG_TXP13 O 17 GND --- 18 GND --- 19 PEG_RXN12 I 20 PEG_TXN12 O 21 PEG_RXP12 I 22 PEG_TXP12 O 23 GND --- 24 GND --- 25 PEG_RXN11 I 26 PEG_TXN11 O 27 PEG_RXP11 I 28 PEG_TXP11 O 29 GND --- 30 GND --- 31 PEG_RXN10 I 32 PEG_TXN10 O 33 PEG_RXP10 I 34 PEG_TXP10 O 35 GND --- 36 GND --- 37 PEG_RXN9 I 38 PEG_TXN9 O
PAGE 279
Pin Assignment 57 PEG_RXP6 I 58 PEG_TXP6 O 59 GND --- 60 GND --- 61 PEG_RXN5 I 62 PEG_TXN5 O 63 PEG_RXP5 I 64 PEG_TXP5 O 65 GND --- 66 GND --- 67 PEG_RXN4 I 68 PEG_TXN4 O 69 PEG_RXP4 I 70 PEG_TXP4 O 71 GND --- 72 GND --- 73 PEG_RXN3 I 74 PEG_TXN3 O 75 PEG_RXP3 I 76 PEG_TXP3 O 77 GND --- 78 GND --- 79 PEG_RXN2 I 80 PEG_TXN2 O 81 PEG_RXP2 I 82 PEG_TXP2 O 83 GND --- 84 GND --- 85 PEG_RXN1 I 86 PEG_TXN1 O 87 PEG_RXP1 I
PAGE 280
Pin Assignment 105 SYSFANON# O 106 EXT_HDMI_DDCDAT I/O 107 MAINON I 108 GND --- 109 GFXPG O 110 EXT_LVDS_PNLCLK I/O 111 VGA_MBDATA I/O 112 EXT_LVDS_PNLDAT I/O 113 VGA_MBCLK I/O 114 GND --- 115 EXT_LVDS_BLON O 116 EXT_VGA_RED O 117 EXT_DISP_ON O 118 GND --- 119 DVI_HPD I 120 EXT_VGA_GRN O 121 GND --- 122 GND --- 123 EXT_HSYNC O 124 EXT_VGA_BLU O 125 EXT_VSYNC O 126 GND --- 127 GND --- 128 EXT_LVDS_TXL#2 O 129 EXT_LVDS_TXU#2 O 130 EX
PAGE 281
Pin Assignment 153 GND --- 154 GND --- 155 GND --- 156 EXT_TV_Y/G O 157 GND --- 158 GND --- 159 GND --- 160 EXT_TV_COMP O 161 NC --- 162 GND --- 163 +5V --- 164 EXT_HDMICLK- O 165 +5V --- 166 EXT_HDMICLK+ O 167 NC --- 168 GND --- 169 GND --- 170 EXT_HDMITX2N O 171 NC --- 172 EXT_HDMITX2P O 173 +3V --- 174 GND --- 175 +3V --- 176 EXT_HDMITX1N O 177 +3V --- 178 EXT_HDMITX1P O 179 +3V --- 180 GND --- 181 +3V --- 182 EXT_HD
PAGE 282
Pin Assignment CN28 RJ45 Connector CONN DIP RJ45 12P 2P FR(H8.0) PIN No. Signal name I/O PIN No. Signal name I/O 1 X-TX0P I/O 2 X-TX0N I/O 3 X-TX1P I/O 4 X-TX2P I/O 5 X-TX2N I/O 6 X-TX1N I/O 7 X-TX3P I/O 8 X-TX3N I/O 9 LAN_VCC4 --- 10 LAN_LINKLED# --- 11 LAN_VCC3 --- 12 LAN_ACTLED# --- CN30 MINI-Card II (HD Decoder) Connector CONN SMD HEADER 52P 2R MS(P0.8,H8) PIN No. Signal name I/O PIN No.
PAGE 283
Pin Assignment 13 CLK_PCIE_MINICARD I 14 LAD3_PCIE I/O 15 GND --- 16 LFRAME#_PCIE I 17 NC --- 18 GND --- 19 NC --- 20 RF_EN_WLAN I 21 GND --- 22 PLTRST# I 23 GPP_RX2N_MINICARD O 24 +3V_HD_VDD --- 25 GPP_RX2P_MINICARD O 26 GND I 27 GND --- 28 +1.
PAGE 284
Pin Assignment 1 USBPWR0 --- 2 BUSBP7- I/O 3 BUSBP7+ I/O 4 GND --- CN32 2'nd SATA HDD Connector CONN DIP HOUSING 22P 1R FR(P1.27,H4.0) PIN No. Signal name I/O PIN No. Signal name I/O 1 GND --- 2 SATA_TXP1 I 3 SATA_TXN1 I 4 GND 5 SATA_RXN1_C O 6 SATA_RXP1_C O 7 GND --- 8 +3.3VSATA2 --- 9 +3.3VSATA2 --- 10 +3.
PAGE 285
Pin Assignment 5 XD_CE#_C I 6 XD_CLE_C O 7 XD_ALE_C I 8 XD_WE#_C I 9 SD_D2_C I/O 10 XD_WPO#_C O 11 GND --- 12 SD_D3_C I/O 13 VCC_XD --- 14 SD/MS_CLK_C I/O 15 SD_CMD_C I 16 MS_D3/XD_D0_C I/O 17 GND --- 18 MS_CD#_C I/O 19 GND --- 20 MS_D2/XD_D1_C I/O 21 VCC_XD --- 22 MS_D0/XD_D2_C I/O 23 MS_D3/XD_D0_C I/O 24 MS_D1/XD_D7_C I/O 25 SD/MS_CLK_C I/O 26 MS_BS/XD_D3_C I/O 27 GND --- 28 GND --- 29 MS_D2/XD_D1_C I/O 30 SD_D0_C I/O 31 MS_D0
PAGE 286
Pin Assignment 1 GND --- 2 SATA_TXP0 I 3 SATA_TXN0 I 4 GND --- 5 SATA_RXN0_C O 6 SATA_RXP0_C O 7 GND --- 8 +3.3VSATA1 --- 9 +3.3VSATA1 --- 10 +3.3VSATA1 --- 11 GND --- 12 GND --- 13 GND --- 14 +5V --- 15 +5V --- 16 +5V --- 17 GND --- 18 NC --- 19 GND --- 20 NC --- 21 NC --- 22 NC --- CN36 USB Connector CONN DIP USB HOUSING 4P 1R FR(H7.6) PIN No. Signal name I/O PIN No.
PAGE 287
Pin Assignment CN38 1394 Port CONN DIP 1394 4P FR(P0.8,H7.2) PIN No. Signal name I/O PIN No. Signal name I/O 1 L1394_TPB0- I/O 2 L1394_TPB0+ I/O 3 L1394_TPA0- I/O 4 L1394_TPA0+ I/O CN39 INT MIC Connector CONN SMD HEADER 2P 1R MR(P1.25,H1.9) PIN No. 1 Signal name I/O ADOGND --- PIN No. 2 Signal name INT_MIC_R I/O --- CN40 Headphone Jack CONN DIP PHONE JACK 8P 1R FR(H6.6) PIN No. Signal name I/O PIN No.
PAGE 288
Pin Assignment CONN DIP PHONE JACK 6P 1R FR(H6.6) PIN No. Signal name I/O PIN No. Signal name I/O 1 ADOGND --- 2 MIC1_L I 3 MIC1_R I 4 Port_B# I 5 ADOGND --- 6 NC --- CN42 FM Connector CONN SMD HOUSING 8P 1R FR(P0.5,H1.5) PIN No. Signal name I/O PIN No. Signal name I/O 1 +3V --- 2 FM_CLOCK O 3 FM_DATA O 4 GND --- 5 FM_LEFT O 6 FM_RIGHT O 7 FM_DET I 8 FM_INTX I CN43 MDC Connector CONN SMD HEADER 12P 2R MR(P0.8,H5.35) PIN No. Signal name I/O PIN No.
PAGE 289
Appendix. D Appendix D Display Codes D.1 Display Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Cap No.
PAGE 290
Display codes Table D-1 Scan codes (set 1 and set 2) (2/4) Cap No.
PAGE 291
Display codes Table D-1 Scan codes (set 1 and set 2) (3/4) Cap No.
PAGE 292
Display codes Table D-1 Scan codes (set 1 and set 2) (4/4) Cap No. Keytop Code set 1 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0 DB E0 1F E0 F0 1F 204 App E0 5D E0 DD E0 2F E0 F0 2F Make Code set 2 Break Make Note Break Notes: 1. 2. 3. 4. 5. 6. 7. * * * * * * * Scan codes differ by mode. Scan codes differ by overlay function.
PAGE 293
Display codes Table D-2 Scan codes with left Shift key Cap Key Code set 1 No.
PAGE 294
Display codes Table D-3 Scan codes in Numlock mode Cap Key Code set 1 No.
PAGE 295
Display codes Table D-5 Scan codes in overlay mode Cap No. Code set 1 Keytop Code set 2 Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 69 38 K (2) 50 D0 72 F0 72 39 L (3) 51 D1 7A F0 7A 40 ; (+) 4E CE 79 F0 79 52 M (0) 52 D2 70 F0 70 54 . (.
PAGE 296
Display codes Table D-7 No.126 key scan code Key top Pause Shift Code set 1 Code set 2 Make Make Common* E1 1D 45 E1 Ctrl* E0 C6 E0 46 9D C5 E1 14 77 E1 F0 E0 7E E0 F0 7E 14 F0 77 *: This key generates only make codes.
PAGE 297
1. United Status (US) Keyboard Figure1 US Keyboard layout 2.
PAGE 298
Figure 2 CH Keyboard layout 3. Thai (TI) Keyboard Figure 3 TI Keyboard layout 4.
PAGE 299
Figure 4 KO Keyboard layout 5.
PAGE 300
6. US International (UI) Keyboard Figure 6 UI Keyboard layout 7.
PAGE 301
8. Danish (DM) Keyboard Figure8 DM Keyboard layout 9.
PAGE 302
Figure9 SW Keyboard layout 10. Arabic (ARE) Keyboard Figure10 ARE Keyboard layout 11.
PAGE 303
Figure11 CZ Keyboard layout 12. Russian (RU) Keyboard Figure12 RU Keyboard layout 13.
PAGE 304
Figure13 PO Keyboard layout 14.
PAGE 305
15. Italian (IT) Keyboard Figure15 IT Keyboard layout 16.
PAGE 306
17. German (GR) Keyboard Figure17 GR Keyboard layout 18.
PAGE 307
19. Hungarian (HG) Keyboard Figure19 HG Keyboard layout 20.
PAGE 308
Figure20 SP Keyboard layout 21. Turkish (TR) Keyboard Figure 21 TR Keyboard layout 22.
PAGE 309
Figure22 TR-F Keyboard layout 23.Swedish (SD) Keyboard Figure 23 SD Keyboard layout 24.
PAGE 310
Figure24 BE Keyboard layout 25.Yugoslavian (YU) Keyboard Figure25 YU Keyboard layout 26.
PAGE 311
Figure26 NW Keyboard layout 27.
PAGE 312
28.Canadian Multinational(AC)Keyboard Figure28 AC Keyboard layout 29.
PAGE 313
30.
PAGE 314
Appendix E Key Layout 1. United Status (US) Keyboard Figure US keyboard 2.
PAGE 315
3. Thai (TI) Keyboard Figure TI keyboard 4.
PAGE 316
5. United Kingdom (UK) Keyboard Figure UK keyboard 6.
PAGE 317
7. Hebrew (HB) Keyboard Figure HB keyboard 8.
PAGE 318
9. Swiss (SW) Keyboard Figure SW keyboard 10.
PAGE 319
11. Czech (CZ) Keyboard Figure CZ keyboard 12.
PAGE 320
13. Portuguese (PO) Keyboard Figure PO keyboard 14.
PAGE 321
15. Italian (IT) Keyboard Figure IT keyboard 16.
PAGE 322
17. German (GR) Keyboard Figure GR keyboard 18.
PAGE 323
19. Hungarian (HG) Keyboard Figure HG keyboard 20.
PAGE 324
21. Turkish (TR) Keyboard Figure TR keyboard 22.
PAGE 325
23. Swedish (SD) Keyboard Figure SD keyboard 24.
PAGE 326
25. Yugoslavian (YU) Keyboard Figure YU keyboard 26.
PAGE 327
27. Scandinavian (ND) Keyboard Figure ND keyboard 28.
PAGE 328
29. Canadian Bilingual (CB) Keyboard Figure CB keyboard 30.
PAGE 329
Fehler! Formatvorlage nicht definiert. Wiring DiagramsFehler! Formatvorlage nicht definiert. Fehler! Formatvorlage nicht definiert. Fehler! Formatvorlage nicht definiert. Appendix F Appendix F F.
PAGE 330
Fehler! Formatvorlage nicht definiert. Wiring DiagramsFehler! Formatvorlage nicht definiert. Fehler! Formatvorlage nicht definiert. Fehler! Formatvorlage nicht definiert.
PAGE 331
Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: BIOS/EC/KBC rewriting disk USB doggle Rewriting the BIOS 1. Set the system to shut down mode. 2. Turn off the power to the computer. 3. Remove the external cables and cards. 4. Connect an external FDD and insert the BIOS rewriting disk into the external FDD. 5.
PAGE 332
Appendix H Appendix H EC/KBC Rewrite Procedures Same as BIOS rewrite Procedures, please refer appendix G Satellite U300 and Satellite Pro U300 Maintenance Manual(960-Q08) H-1
PAGE 333
Appendix I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) in maximum configuration.
PAGE 334
Reliability Satellite P300 and Satellite Pro P300 Maintenance Manual(960-Q08) I-2