Addendum

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 78563

FormNo.3362-713RevA

EZVac

™

Baggers

AllG3EZVac

™

Baggers

Addendum

Ensuretheparkingbrakeisadjusted.Keepthis

addendumwithyourOperator’sManual.

AdjustingtheParkingBrake

Checktomakesurebrakeisadjustedproperly.

1.Drivethemachineontoalevelsurface.

2.Disengagethebladecontrolswitch(PTO),movethe

motioncontrolleverstotheneutrallockedposition

andsettheparkingbrake.

3.Stoptheengine,waitforallmovingpartstostop,

andremovethekey.

4.Raisethebackofthemachineupandsupportthe

machinewithjackstands.

Raisingthemowerdeckforserviceor

maintenancerelyingsolelyonmechanical

orhydraulicjackscouldbedangerous.The

mechanicalorhydraulicjacksmaynotbe

enoughsupportormaymalfunctionallowing

theunittofall,whichcouldcauseinjury.

DoNotrelysolelyonmechanicalorhydraulic

jacksforsupport.Useadequatejackstandsor

equivalentsupport.

5.Removethereartiresfromthemachine.

6.Removeanydebrisfromthebrakearea.

7.Open(pushposition)thedrivewheelreleasevalves.

RefertoUsingtheDriveWheelReleaseValves

sectioninOperation.

8.Disengagetheparkingbrake.

9.Holdthethreadedrodendwithatoolandloosen

thelocknutawayfromthestandardnut(Figure1).

DoNotallowthecabletoturnwhenthenutsare

beingloosened.

Figure1

LeftHandBrakeShown

1.Cableanchor

7.Pullcablethreadedrod

thisdirection

2.Threadedrod8.Holdthreadedrodhere

3.Pushleverthisdirection

9.Swivel(pivothead)

4.Caliperleverarm10.Caliper

5.Standardnut(shown

againstswivel)

11.Hub

6.Locknut

10.Removeallslackfromcablebypullingonthe

threadedrodend(locknut)withamediumamount

offorce.Usingtheotherhandandngersonly,push

thecaliperleverarmtoengagethebrakepadsonthe

rotoruntiltheleverstops.Whileholdingtheleverat

thestoppedposition,pulltheslackoutofthecable

threadedendthroughtheswivel.Spinthestandard

nutagainsttheswiveltoholdthecaliperleverarm

inplace(Figure1).

Notetheorderofthestandardnutandlocknut(no

nutonthecableanchorsideoftheswivel).

11.Releasethecaliperleverandcable.Turnthewheel

hubbyhandinbothdirectionsrelativetothecaliper;

slightdragofthecaliperpadonthewheelhubis

desired.

12.Ifthereisnomovementbetweenthehubandthe

caliperthenbackoffthestandardnutoneturnfrom

theswivelandrepeatstep11(drivereleasevalves

mustbeintheopenpositiononthehydros).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3362-713 Rev A E Z Vac™ Baggers All G3 E Z Vac™ Baggers Addendum Ensure the parking brake is adjusted. Keep this addendum with your Operator’s Manual. Adjusting the Parking Brake Check to make sure brake is adjusted properly. 1. Drive the machine onto a level surface. 2. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. 3. Stop the engine, wait for all moving parts to stop, and remove the key. 4.
PAGE 2
13. If the hub moves very freely relative to the caliper, then tighten the standard nut one turn against the swivel and repeat step 11. Engine must be running and drive wheels must be turning so brake burnishing can be performed. Contact with moving parts or hot surfaces may cause personal injury. 14. After adjusting the brakes on both sides of the mower, cycle the brake handle a minimum of six times to allow the cable to seat into the sheath and mounting tabs.
PAGE 3
Form No. 3362-713 Rev A Ensacadores E-Z Vac™ Todos los Ensacadores E Z Vac™ G3 Anexos Asegúrese de que el freno de estacionamiento está ajustado. Guarde este Anexo con su Manual del operador. Ajuste del freno de estacionamiento Compruebe que el freno está correctamente ajustado. 1. Coloque la máquina sobre una superficie nivelada. 2. Desengrane el mando de control de las cuchillas, ponga las palancas de control de movimiento en posición de bloqueo/punto muerto, y ponga el freno de estacionamiento. 3.
PAGE 4
12. Si no hay movimiento entre el cubo y la pinza, afloje la tuerca estándar una vuelta y repita el paso 11 (las válvulas de desvío de las transmisiones deben estar en la posición de abierto). 13. Si el del cubo se mueve muy libremente respecto a la pinza, apriete las tuercas de las ruedas una vuelta contra el pivote y repita el paso 11. 14.