Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 78540

FormNo.3370-467RevA

DeluxeSeatKit

ZMaster

G3RidingMower

ModelNo.117-6174

ModelNo.78540

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removetheseat(Domesticand

AustralianMowers).

Nopartsrequired

–

Removetheseat(InternationalMowers).

SeatBeltKit

1Installtheseatbelt.

Deluxesuspensionseat1

Flangenut(5/16inch)

Plasticties4

Installtheseat(DomesticandAustralian

Mowers).

Deluxesuspensionseat1

Flangenut(5/16inch)

Flangenut(3/8inch)(International

mowersonly)

Plasticties4

Installtheseat(InternationalMowers).

Decal1Installthedecal.

RemovingtheSeat(Domestic

andAustralianMowers)

NoPartsRequired

Procedure

1.Unlatchtheseatandtiptheseatforward.

2.Removethenutsholdingtheseattothemounting

frame(Figure1).

3.Disconnectthewireharnessfromtheseatswitch.

4.Removetheseatfromtheframeandsetitaside.

Figure1

1.Seat

3.Nut

2.Seatframe

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3370-467 Rev A Deluxe Seat Kit Z Master® G3 Riding Mower Model No. 117-6174 Model No. 78540 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. No parts required – Remove the seat (Domestic and Australian Mowers). No parts required – Remove the seat (International Mowers). Seat Belt Kit 1 Install the seat belt.
PAGE 2
Removing the Seat (International Mowers) No Parts Required Procedure 1. Remove the hydraulic unit shroud from the machine (Figure 2). Save hardware and shroud. Figure 3 1. Harness connector 2. Flange nuts 4. Remove the seat plate from the seat by removing the 4 spacers and 4 flange nuts (Figure 4). Figure 2 1. Hydraulic unit shroud 2. Bolts 2. Remove the 4 flange nuts holding the seat to the machine (Figure 3). 3.
PAGE 3
Installing the Seat Belt Parts needed for this procedure: 1 Seat Belt Kit Procedure WARNING Serious injury or death can happen when the seat belt is used without a roll bar installed. Do not install the seat belt without a roll bar installed. If you do not have a rollbar, contact an Authorized Service dealer to obtain the correct Roll Over Protection System (ROPS). Figure 5 1. Bolt, (7/16 x 1 inch) 2. Seat belt retractor 3.
PAGE 4
5 Installing the Seat (International Mowers) Parts needed for this procedure: Figure 6 1. Seat 2. Seat plate 3. Flange nut (5/16 inch) 1 Deluxe suspension seat 4 Flange nut (5/16 inch) 4 Flange nut (3/8 inch) (International mowers only) 4 Plastic ties Procedure 4. Plug the harness connector into the seat switch located under the seat (Figure 7). 1. Remove the plastic packing covers guarding the seat studs. Do not remove the spacers on the seat studs. 2.
PAGE 5
6 Installing the Decal Parts needed for this procedure: 1 Decal Procedure Remove the backing off the decal and place the decal on the back of the seat as shown in Figure 11. Figure 9 1. Harness connector 2. Flange nuts (3/8 inch) 7. Install the hydraulic unit shroud to the machine (Figure 10). Figure 11 1. Back of seat Figure 10 1. Hydraulic unit shroud 2. Bolts 8. Move seat to the furthest rear position. Use the plastic ties to attach the wire harness to the seat. 9.
PAGE 6
Operation Positioning the Seat Changing the Seat Position The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable. 1. To adjust, push the lever downward to unlock seat (Figure 12). 2. Slide the seat to the desired position and release lever to lock in position. Changing the Seat Suspension The seat can be adjusted to provide a smooth and comfortable ride. Position the seat where you are most comfortable.
PAGE 7
Notes: 7
PAGE 8