Operator's Manual
Table Of Contents
- NO TITLE
- NO TITLE
- NO TITLE
- NO TITLE
- During Operation Safety
- Entering the Operator’s Position
- Operating the Parking Brake
- Operating the Mower Blade-Control Switch (PTO)
- Operating the Throttle
- Operating the Choke
- Starting the Engine
- Shutting Off the Engine
- Using the Motion-Control Levers
- Driving the Machine
- Using the Side Discharge
- Adjusting the Height of Cut
- Adjusting the Anti-Scalp Rollers
- Adjusting the Flow Baffle Cam Locks
- Positioning the Flow Baffle
- NO TITLE
- NO TITLE
- NO TITLE
- NO TITLE
- NO TITLE
- NO TITLE
- What is this warning?
- What is Prop 65?
- Does this law apply everywhere?
- How do the California warnings compare to federal limits?
- Why don’t all similar products carry the warning?
- Why does Toro include this warning?
g026961
Figure79
LeftSideShown
1.L-bracket4.Rearlinkageassembly
2.Linkagestop
5.Caliper
3.Gap
6.Wheelhub
8.Disengagetheparkingbrake,thelevershould
beinthedownposition.
9.Turnthewheelhubbyhandinbothdirections
relativetothecaliper;thewheelhubshould
movefreelybetweenthecaliper.
10.Ifagapisneededorthewheelhubdoesnot
movefreely:
A.Disengagetheparkingbrake.
B.Disconnectandne-tunetherearlinkage
assembly:
•Shortenthelinktocreateagap.
•Lengthenthelinktoallowwheelhub
movement.
C.Connecttherearlinkageassembly.
11.Engagetheparkingbrakeandcheckthegap.
12.Repeatsteps8through12untilavisiblegapis
achievedandthewheelhubrotatesfreely.
13.Repeatthisprocedureforthebrakeonthe
oppositeside.
14.Rotatethedrive-wheelreleasehandleto
theoperatingposition;refertoUsingthe
Drive-Wheel-ReleaseValves(page33).
15.Installthereartiresandtorquethelugnuts;
refertoCheckingtheWheelLugNuts(page50).
16.Removethejackstands.
BeltMaintenance
InspectingtheBelts
ServiceInterval:Every50hours
Replacethebeltifitisworn.Thesignsofawornbelt
includesquealingwhilethebeltisrotating;theblades
slippingwhilecuttinggrass;andfrayededges,burn
marks,andcracksonthebelt.
ReplacingtheMowerBelt
1.Parkthemachineonalevelsurface,disengage
theblade-controlswitch(PTO),andengagethe
parkingbrake.
2.Shutofftheengine,removethekey,andwait
forallmovingpartstostopbeforeleavingthe
operatingposition.
3.Lowerthemowertothe76mm(3inch)
height-of-cut.
4.Removethebeltcovers(Figure80).
g027729
Figure80
1.Pushthetabdown2.Removethebeltcover
5.Usearatchetinthesquareholeintheidlerarm
toremovetensionontheidlerspring(Figure81).
6.Removethebeltfromthemower-deckpulleys.
7.Removethebeltguideonthespring-loaded
idlerarm(Figure81).
8.Removetheexistingbelt.
9.Installthenewbeltaroundthemowerpulleys
andtheclutchpulleyundertheengine(Figure
81).
55