Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74921

FormNo.3360-657RevB

ZMaster

G3Mowers

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Unfoldthecrate.

Nopartsrequired

–

Checkthetirepressure.

Nopartsrequired

–

Chargethebattery.

Nopartsrequired

–

Checktheengineoillevel.

Nopartsrequired

–

Addfueltothemachine.

Number2generalpurposelithiumbase

ormolybdenumbasegrease.(Purchase

separately.)

1tube

Checkthemachineforgrease.

Nopartsrequired

–

Preparethesidedischargechute.

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer.

Operator’sManual

EngineOwner’sManual

RegistrationCard

Operatortrainingmaterial

Key2

Deliveringthemachinetothecustomer.

UnfoldingtheCrate

NoPartsRequired

Procedure

RefertothePackagingCrateInstructionsincludedwith

themachine.

CheckingtheTirePressure

NoPartsRequired

Procedure

Pressure:13psi(90kPa)

Note:Thefrontcasterwheelisasemi-pneumatictire

anddoesnotneedtobechecked.

Checktheairpressureinthedrivetires.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3360-657 Rev B Z Master® G3 Mowers Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 Description Use Qty. No parts required – Unfold the crate. No parts required – Check the tire pressure. No parts required – Charge the battery. No parts required – Check the engine oil level. No parts required – Add fuel to the machine. Number 2 general purpose lithium base or molybdenum base grease. (Purchase separately.
PAGE 2
Figure 1 Figure 2 3 4 Charging the Battery Checking the Engine Oil Level No Parts Required No Parts Required Procedure Procedure Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Servicing the Engine Oil Level in Operator’s Manual. Charging the battery produces gasses that can explode and cause serious injury. • Keep cigarettes, sparks and flames away from the battery. 5 • Make sure the ignition switch is off.
PAGE 3
G009189 1 2 Figure 4 3 2. Check the grease for the pump drive belt idler arm. 4 G008942 Figure 3 6 Figure 5 Checking the Machine for Grease 3. Check the grease in the caster pivots and caster wheel bearings (Figure 6). Parts needed for this procedure: 1 tube Number 2 general purpose lithium base or molybdenum base grease. (Purchase separately.) Procedure 1. Check the grease for the three spindle bearings and the idler pulley. If needed, add grease until it comes out of the lower seals.
PAGE 4
6 7 2 4 7 Checking the Side Discharge Chute 3 No Parts Required 1 Procedure 5 If there are plastic ties holding the side discharge chute up, remove them and lower the chute into place. g015594 Figure 7 1. Bolt 2. Spacer 3. Locknut 4. Spring An uncovered discharge opening could allow the lawn mower to throw objects in the operator’s or bystander’s direction and result in serious injury or death. Also, contact with the blade could occur.
PAGE 5
8 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the mower. Check that all mower spindles are greased. Check the engine oil level. Check the hydraulic fluid level.
PAGE 6
9 Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator’s Manual 1 Engine Owner’s Manual 1 Registration Card 1 Operator training material 2 Key Procedure At delivery, Fill in the model and serial number and complete the items listed in the following table and initial each when finished. Model No. Serial No.
PAGE 7
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: • Fuel tank caps • Oil fill cap/Oil dipstick • Spark plug(s) • Engine oil filter • Engine oil drain • Fuel filters • Air filter • Radiator coolant (if applicable) • Hydraulic fluid reservoir • Hydraulic filter • Battery • Ignition switch • Throttle lever • Choke (if applicable) • Power take off switch (PTO) • Motion control levers • Parking brak
PAGE 8