Setup Instructions

ManualsBrandsToro ManualsOutdoor Power EquipmentTimeCutter MX5075 with MyRIDE Suspension System 50 in. Fab 24.5 HP V-Twin Gas Dual Hydrostatic Zero Turn Riding Mower

FormNo.3420-276RevB

TimeCutter

RidingMowers

ForTimeCutter

RidingMowerswithMyRide

Suspension

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Pin1

Roundclip2

InstalltheMyRidesuspension.

Nopartsrequired

–

Connectthebattery.

Nopartsrequired

–

Installtheseat(machineswithMyRide

suspensionandshippedinawoodcrate

only).

Rearhitch1

Bolt(5/16x1inch)

Locknut(5/16inch)

Installtherearhitch.

Nopartsrequired

–

Setupthemotion-controllevers.

Nopartsrequired

–

Checkthemoweradjustment.

Ignitionkey1

Hosecoupling(notincludedwithCE

models)

Operator'sManual

Engineowner’smanual(non-Toro

engines)

Operatortrainingmaterial

Completingthesetup.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3420-276*B

Summary of content (8 pages)

PAGE 1
Form No. 3420-276 Rev B TimeCutter® Riding Mowers For TimeCutter® Riding Mowers with MyRide® Suspension Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 2 Pin Round clip 1 2 Install the MyRide suspension. No parts required – Connect the battery. 3 No parts required – Install the seat (machines with MyRide suspension and shipped in a wood crate only).
PAGE 2
1 Installing the MyRide® Suspension Machines with MyRide Suspension and Shipped in a Wood Crate Only Parts needed for this procedure: 1 Pin 2 Round clip Procedure 1. 2. Raise the platform and remove the wooden block from above the battery. g233947 Figure 2 Note: You can discard the wooden block. 1. Pin 4. Round clip Rotate the suspension up (Figure 1). 2. Post 5. Shape of the key slot 3. Spring g233946 Figure 1 3. Place the ends of the springs on the posts (Figure 2). 4.
PAGE 3
2 3 Connecting the Battery Installing the Seat No Parts Required Machines with MyRide Suspension and Shipped in a Wood Crate Only Procedure 1. Locate the battery and negative battery cable. No Parts Required 2. Remove the plastic cap from the negative battery post. Procedure 3. Remove the fasteners on the negative battery cable, and use them to secure the negative battery cable to the negative battery post (Figure 3). 1.
PAGE 4
2. Place the seat assembly onto the platform (Figure 5). 4. Install a hairpin cotter on 1 side of the seat-pivot rod, then slide the seat-pivot rod through the pivot bracket hole and seat pan hole (Figure 7). g233953 Figure 7 5. Install the other hairpin cotter on the other side of the seat-pivot rod (Figure 8). g233955 Figure 5 3. Install the seat-pivot rod by inserting the rod from the center and outward through the pivot bracket hole and seat pan hole (Figure 6).
PAGE 5
6. Rotate the seat assembly upward and connect the wire harness to the seat switch on the bottom of the seat (Figure 9). g015398 Figure 11 After assembly g233951 Figure 9 1. Seat switch 4 Installing the Rear Hitch Parts needed for this procedure: 1 Rear hitch 2 Bolt (5/16 x 1 inch) 2 Locknut (5/16 inch) Procedure Install the bracket to the frame as shown in Figure 10 and Figure 11. g015397 Figure 10 Before assembly 1. Bolts 2.
PAGE 6
5 7 Setting Up the Motion-Control Levers Completing the Setup Parts needed for this procedure: No Parts Required Procedure 1. Locate the motion-control levers attached, but folded down on the machine. 2. Remove the upper bolt (3/8 x 1 inch) and washer; loosen the lower bolt (3/8 x 1 inch). 3. Raise the motion control levers to the upright position. 4.
PAGE 7
Notes:
PAGE 8