Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74463

Table Of Contents

FormNo.3407-539RevA

TITAN

HDSeriesRidingMowers

ModelNo.Allmodels

SetupInstructions

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removethemachinefromthecrate.

Nopartsrequired

–

Addfueltothemachine.

Nopartsrequired

–

Checktheengine-oillevel.

Nopartsrequired

–

Servicethehydraulicoil.

Nopartsrequired

–

Checkthetirepressure.

Nopartsrequired

–

Servicingthebattery.

Nopartsrequired

–

Raisetherolloverprotectionsystem

(ROPS).

Nopartsrequired

–

Checkthegrassdeector.

No.2lithiumormolybdenum-based

grease(purchaseseparately)

1tube

Checkthemachineforgrease.

Locknut(3/8inch)

Carriagebolt(3/8x2-1/4inches)

Installtherightbumper(reardischarge

modelsonly).

Nopartsrequired

–

Checkthemoweradjustment.

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer(allmachines).

Operator'sManual

Engineowner'smanual(non-Toro

engines)

Operator-trainingmaterial

Key2

Registrationcard1

Deliverthemachinetothecustomer(all

machines).

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3407-539*A

Summary of content (8 pages)

PAGE 1
Form No. 3407-539 Rev A TITAN® HD Series Riding Mowers Model No. All models Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 10 11 12 13 Description Use Qty. No parts required – Remove the machine from the crate. No parts required – Add fuel to the machine. No parts required – Check the engine-oil level. No parts required – Service the hydraulic oil. No parts required – Check the tire pressure.
PAGE 2
1 4 Removing the Machine from the Crate Servicing the Hydraulic Oil No Parts Required No Parts Required Procedure Procedure This machine is shipped filled with hydraulic fluid in the reservoirs. If removing the machine from a metal crate, refer to the Dealer/Distributor Portal for further information. Check the expansion tank; if necessary, add Toro® HYPR-OIL™ 500 hydraulic fluid, as recommended in the Operator's Manual, to the FULL COLD line (Figure 1).
PAGE 3
5 Checking the Tire Pressure No Parts Required Procedure Pressure: 13 psi (90 kPa) Figure 2 Note: Check the tire pressure before starting the machine. Refer to your Operator’s Manual for the correct tire type and procedure. 7 6 Raising the Rollover Protection System (ROPS) Servicing the Battery No Parts Required No Parts Required Procedure Procedure WARNING 1. Pull both knobs out and rotate them 90 degrees so that they are not engaged (Figure 3).
PAGE 4
8 Checking the Grass Deflector No Parts Required Procedure If there are plastic ties holding the grass deflector up, remove them and lower the deflector into place. WARNING An uncovered discharge opening could allow the machine to throw objects in the operator's or bystander's direction and result in serious injury or death. Also, contact with the blade could occur. Never operate the machine without a cover plate, a mulch plate, grass deflector, or bagger installed. 1.
PAGE 5
9 10 Checking the Machine for Grease Installing the Right Bumper Parts needed for this procedure: Parts needed for this procedure: 1 tube No. 2 lithium or molybdenum-based grease (purchase separately) 3 Locknut (3/8 inch) 3 Carriage bolt (3/8 x 2-1/4 inches) Procedure Procedure Mount the side bumpers in the top holes when operating in height of cut higher than 64 mm (2-1/2 inches) and in the center holes when operating in height of cut lower than 64 mm (2-1/2 inches).
PAGE 6
11 Checking the Mower Adjustment No Parts Required Procedure Adjust the side-to-side level and the front-to-rear blade slope. Use the relevant procedures in the Operator's Manual to verify that the deck is level, and make any adjustments as necessary.
PAGE 7
12 Checking the Machine Before Delivery to the Customer (All Machines) No Parts Required Procedure Before delivering the machine to the customer, ensure that you have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the mower deck. Check the engine-oil level. Check the hydraulic-fluid level. Check that the ROPS is secure.
PAGE 8
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: • Fuel tank • Oil-fill cap/Oil dipstick • Spark plug(s) • Engine-oil filter • Engine-oil drain • Fuel gauge, valve, and hose • Air filter • Hydraulic-fluid reservoir • Hydraulic filter • Battery • Ignition switch • Throttle lever • Choke (if applicable) • Power takeoff switch (PTO) • Motion-control levers • Parking brake • Height of cut • Lift