Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74410

FormNo.3356-183RevB

Z400SeriesZMaster

Mowers

ForallZ400SeriesZMasterMowers

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removepartsfromthecrate.

Nopartsrequired

–

Checkthetirepressure.

Rearwheels2Installthedrivewheels.

Rollbar,rightsection1

Rollbar,leftsection

Rollbar,centersection1

Bolt,(3/8x1inch)

Curvedwasher

Flangenut,(3/8inch)

Bolt,(1/2x3–1/4inch)

Flangenut,(1/2inch)

InstalltheRolloverProtectionSystem

(ROPS).

Nopartsrequired

–

Installtheseat.

Rightcontrollever1

Leftcontrollever

Bolt(3/8x1inch)(2areassembled)

Curvedwasher(3/8inch)(2are

assembled)

Installthemotioncontrollevers.

Nopartsrequired

–

Addingfueltothemachine.

Nopartsrequired

–

Chargethebattery.

Aircleanercap1

Hoseclamp1

Installtheaircleanercap.

Number2generalpurposelithiumbase

ormolybdenumbasegrease.(Purchase

separately.)

1tube

Checkthemachineforgrease.

Nopartsrequired

–

Checktheengineoillevel.

Nopartsrequired

–

Preparethesidedischargechute.

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (12 pages)

PAGE 1
Form No. 3356-183 Rev B Z400 Series Z Master® Mowers For all Z 400 Series Z Master Mowers Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Use Qty. No parts required – Remove parts from the crate. No parts required – Check the tire pressure. Rear wheels 2 Install the drive wheels.
PAGE 2
Procedure 14 Description Operator’s Manual Parts Catalog Engine Owner’s Manual Registration Card Safety Video Key 1 Qty. Use 1 1 1 1 1 2 Delivering the machine to the customer. 3 Removing Parts from the Crate Raising the Machine Up and Installing the Drive Wheels No Parts Required Parts needed for this procedure: Procedure 2 Remove the tires, the seat and the parts for the ROPS from the shipping crate. Rear wheels Procedure 2 1.
PAGE 3
4 Installing the Roll Over Protection System Parts needed for this procedure: Figure 3 3. Remove the wheel nuts from both sides of the vehicle and remove the right angle retaining plate. Discard the screws and retaining plate. 1 Roll bar, right section 1 Roll bar, left section 1 Roll bar, center section 8 Bolt, (3/8 x 1 inch) 8 Curved washer 8 Flange nut, (3/8 inch) 2 Bolt, (1/2 x 3–1/4 inch) 2 Flange nut, (1/2 inch) Procedure 1.
PAGE 4
2. Install the lanyard clips onto the long bolts (1/2 x 3-1/4 inch). Note: Make sure the bent tab points toward the head of the bolt. Figure 7 3. Lightly oil the ends of the center roll bar section. Figure 9 4. Loosely install the center roll bar section using 2 bolts (1/2 x 3-1/4 inch) and 2 flange nuts (1/2 inch). 6. Torque all lower fasteners, attached to the machine frame, to 30 ft-lb. Note: Make sure the bolts are installed from the outside of the roll bar. 7.
PAGE 5
Figure 12 5. Install the seat rod to the seat frame. Figure 11 5 Installing the Seat No Parts Required Figure 13 Procedure 1. Remove the bolt and nut from the seat frame. 6 2. Remove the nuts from the studs under the seat. 3. Secure the seat rod to the seat with the bolt and nut. Installing the Motion Control Levers 4. Install the seat to the seat frame with the previously removed nuts.
PAGE 6
Note: Install the control levers in the top and middle holes for the high position or the middle and bottom holes for the low position, as desired. 7 Adding Fuel to the Machine No Parts Required Procedure Add fuel to the machine before starting it. Refer to your Operator’s Manual. for the correct fuel and procedure. Figure 14 8 3. Raise the levers and align them together in the neutral position and tighten the bolts.
PAGE 7
2. Remove the air cleaner cap from the machine. 3. Install the hose clamp onto the air cleaner cap. Figure 16 Figure 18 9 4. Install the air cleaner cap onto the air cleaner and secure it with the hose clamp. Installing the Air Cleaner Cap Parts needed for this procedure: 1 Air cleaner cap 1 Hose clamp Procedure Note: Do not use this procedure for Estate models. 1. Remove the plastic plug.
PAGE 8
10 11 Checking the Machine for Grease Checking the Engine Oil Level No Parts Required Parts needed for this procedure: 1 tube Procedure Number 2 general purpose lithium base or molybdenum base grease. (Purchase separately.) Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking Oil Level in Operator’s Manual. Procedure 1. Remove the belt covers. 12 2. Check the tensioning arm for grease. 3. Check the grease for the three spindle bearings.
PAGE 9
13 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the mower. Check that all mower spindles are greased. Check the engine oil level.
PAGE 10
14 Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator’s Manual 1 Parts Catalog 1 Engine Owner’s Manual 1 Registration Card 1 Safety Video 2 Key Procedure At delivery, complete the items listed in the following table and initial each when finished. Model No. Serial No.
PAGE 11
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: Fuel tank caps Oil fill cap/ Oil dipstick Engine oil filter Engine oil drain Fuel filters Air filter Hydraulic fluid reservoir Hydraulic filter Battery Ignition switch Throttle lever Power take off switch (PTO) Motion control levers Parking brake Mower height-of-cut Adjustable seat Hydraulic bypass valves Rollover Protection System (ROPS) Mower deck flow baffle Refer to theOper
PAGE 12