Service Manual

P224
DESCRIPTION
CYLINDER BLOCK
Cylinder Bore Honed Diameter ............................
Maximum Allowable
Taper
............... .................................
Out-of-Round ..........................................
Main Bearing Inside Diameter (Without bearing) .............
Main Bearing Inside Diameter (Installed) ....................
Camshaft Bearing Bore (Bearing Installed) ..................
CRANKSHAFT
Main Bearing Journal Diameter ............................
Main Bearing Clearance ..................................
Connecting Rod Journal Diameter .........................
Crankshaft End Play ......................................
CONNECTING ROD
Large Bore Diameter (Without bearing installed and rod bolts
properly torqued)
........................................
Connecting Rod Side Clearance ...........................
Piston Pin Bushing Bore (Without bushing) ..................
Piston Pin Bushing Bore (Finished bore) ....................
Bearing to Crankshaft Clearance ...........................
CAMSHAFT
Bearing Journal Diameter .................................
Bearing Clearance .......................................
End Play ................................................
Lobe Height
Intake
..................................................
Exhaust ................................................
PISTON
Clearance in Cylinder
Measure
90° to pin 1.187 inch below top of piston .........
Piston Pin Bore ..........................................
Ring Groove Width
Top Compression Ring .................................
Middle Compression Ring ...............................
Bottom Oil Control Ring .................................
PISTON PIN
Clearance in Piston .......................................
Diameter ................................................
Clearance in Connecting Rod .............................
PISTON RINGS
Clearance
Top Groove ...........................................
Ring End Gap in Cylinder .................................
MINIMUM
Inches
3.5625
2.1 870
2.001 5
1.3757
1.9992
0.0024
1.6252
0.0060
1.7505
0.0020
0.81 15
0.7504
0.0020
1.3740
0.001 5
0.01 10
0.0070
0.7502
0.0800
0.0800
0.1 880
0.00004
0.0002
0.7500
0.0020
0.01 00
(mm)
(90.49)
(55.55)
(50.84
(34.94)
(50.78)
(0.061)
(41.28)
(0.1 52)
(44.46)
(0.051 )
(20.61)
(1 9.06)
(0.051)
(34.90)
(0.038)
(0.279)
1
. 1670
1.1 570
(0.1 78)
(1 9.06)
(2.032)
(2.032)
(4.775)
(0.001)
(0.005)
(1 9.05)
(0.051)
(0.254)
Inches
3.5635
0.003
0.003
2.1 880
2.0040
1.3787
2.0000
0.0042
1.6260
0.01 20
1.751 0
0.01 60
0.81 25
0.7508
0.0033
1.3745
0.0030
0.0480
(29.64)
(29.39)
0.0090
0.7506
0.081
0
0.081 0
0.1 890
0.00064
0.0008
0.7502
0.0080
0.0200
(90.51)
(0.08)
(0.08)
(55.58)
(50.90)
(35.02)
(50.80)
(0.1 07)
(41
. 30)
(0.305)
(44.48)
(0.406)
(20.64)
(1 9.07)
(0.084)
(34.91)
(0.076)
(1
(0.229)
(1 9.07)
(2.057)
(2.057)
(4.801)
(0.01 6)
(0.020)
(1 9.06)
(0.203)
(0.508)