FORM NO. 01-502-0750 MODEL NO. 44510 20101 & UP OPERATOR'S MODEL NO.
FOREWORD Thank you for buying a high quality Toto turf care product. To get the best performance from this machine, operate and maintain it according to the instructions in this manual. Toto also wants to stress the importance of safety. You and anyone else using or maintaining this machine are strongly urged to read this manual, especially all the safety instructions. DANGER, WARNING and CAUTION, used with the triangular safety alert symbol, highlight safety messages.
TABLE OF CONTENTS Page SAFETY INSTRUCTIONS 3-4 SAFETY AND INSTRUCTION DECALS 5 SPECIFICATIONS .. B BEFORE OPERATING . 7 CONTROLS OPERATING INSTRUCTIONS .9 LUBRICATION .. 9 Page MAINTENANCE 10 TROUBLESHOOTING . . .M STORAGE 2 IDENTIFICATION AND ORDERING 12 MAINTENANCE CHART 13-15 THE COMPROMISE Back Cover SAFETY INSTRUCTIONS The safety alert symbol means CAUTION, WARNING or DANGER "personal safety instruction”. Read and understand the instruction because it has to do with safety.
SAFETY INSTRUCTIONS (Continued) WHILE OPERATING ENDANGER ROTATING MEMBERS CAN CAUSE SERIOUS PERSONAL INJURY « Keep hands and feet away from reel area. 8. Do not run the engine in a confined area without adequate ventilation. Exhaust fumes are hazardous and could possibly be deadly. 9. Maximum seating is one person; therefore never carry passengers. 10. Do not touch engine, muffler or radiator while engine is running or soon after it is stopped, These areas could be hot enough to cuss a burn. 11.
SAFETY AND INSTRUCTION DECALS The following safety and instruction decals reinstalled on the unit. Replace any decals that becomes damaged or illegible. Part numbers for decals are listed below and in your Parts Catalog. Order replacements from your Authorized Toto Distributor. ON GAS TANK ON MAIN FRAME {Part No. 01-506-0460} (Part No. 01-506-0430} OGS ¢ -H]I L4 ’i I ON MAIN FRAME I {Part No. 01-506-0540} R . ON FAN HOUSING {Part No. 01-506-0290} A DANGER FIRE HAZARD.
SPECIFICATIONS FAN: 6 blades, single outlet, 20" diameter, 4000 CFM. ENGINE: 20 HP Oman Performer, 2 cylinder FRAME: All welded steel construction FAN DRIVE: crankshaft, 2" welded hub with taper lock. COUPLET: Power band belt FUEL TANK: gallon CHUTE : 12 ga. top tor extended wear, 14 gravesides. 917 from ground to lover edge of chute opening. BEARINGS: Self sealed throughout (1) 2" pillow block, (1) 1 1/4" pillow block INTAKE HOSE: 9, 12"diameter, flexible. FENDERS: 10ga. waded TIRES: 5.
BEFORE OPERATING CHECK TIRE PRESSURE Check tire pressure before each use. Inflate to 22 PSL. CHECK CRANKCASE OIL Qil recommendations are: SAE T0W30 SF-CC The engine is shipped with 2-1/2 quarts of oiling the crankcase, however, level of oil must be checked before and after the engine is first started. 1. Position the loader on a level surface and make sure engine is off, 2. Remove the dipstick and wipe it with a clean rag. Push dipstick down into the tube and ensure iris fully seated.
CONTROLS THROTTLE CONTROL (Fig. 1) The throttle operates the engine at various speeds. Moving throttle forward increases engine speed:; backwards decreases engine speed. KEY SWITCH (Fig. 1) The key switch starts and stops the engine and has two positions: "OFF" and "ON". Rotate key clockwise to engage starter motor. When engine stats, release key and it will move automatically to the "ON" position. To shut engine off, rotate key counterclockwise to the "OFF" position. Remote Bracket \_ Intake Hose INTAKE HO
OPERATING INSTRUCTIONS A\ CAUTION THROWN OBJECTS FROM THE DISCHARGE CHUTE CAN CAUSE PERSONAL INJURY. ¢ Before starting, position the discharge chute away from any bystanders. 1. Park the union a level surface . 2. Move the jack to the down position. Turn the Jack handle until the units level with the surface. 3. Start engine with the throttle barely open and choke pulled out. When engine starts, push choke in gradually. 4. Run engine to full throe. 5.
MAINTENANCE BELT TENSION (Fig. 3) The belt is properly adjusted when it has 1/4 deflection with sighs. of force. To decrease tension, to increase tension.
TROUBLE SHOOTING CONDITION CAUSE CORRECTION TOO MUCH VIBRATION e Remove hose from fan housing. Dec lean out any objects in the bros in the impeller, impeller. LOSING SUCTION » Long chute blocked. Clean out any blockage, Hose blockade. Loose blat. incorrect engine speed. Clean out the hose. Adjust the tension. See belt adjustments in manual. Set the R.P.M. to 3600.
STORAGE 1. Thoroughly clean the loader so iris free of dirt, leaves and debris. 2. Inflate tires to 22 PSI. 3. Check all fasteners for looseness: tighten as necessary. 4. Grease or oil all grease fittings ‘and bearings, Wipe off excess lubricant. 5. Check the tension and condition of the drive belt 8. Service the battery and cables as folios: A. Remove the battery terminals from the battery posts. B. Clean the battery, terminals and posts with a wig brush and baking soda solution, C.
The Toto Promise A ONE YEAR LIMITED WARRANTY The Toto Company promises to repair your TOR Product if defective in materials or workmanship. The following time periods from the date of purchase apply: Commercial Products 1 Year The costs of pares and labor are included, but the customer pays the transportation costs on walk rotary mowers with cutting widths of less than 25, It you feet your TOR products defective and wish to rely on The Toto Promise, the following procedure is rerecorded: .