MODEL NO. 4111950001 & UP MODEL NO. 41020-50001 & UP MODEL NO. 41021-50001 & UP MODEL NO. 41128-50001 & UP MANUAL VALVE SPRAY SYSTEM FOR THE MULTI-PRO™ 1100 VEHICLE SET-UP AND PARTS CATALOG Refer to the illustrated Pan's List for the details of parts used in assembling the Manual Valve Spray System. NOTE: "Right', "Left", "Front”, and "Rear" are referenced while seated in the operator's position. TACHOMETER: 1.
4. Remove lower rear com nut from left end of Control Valve, Attach Valve Brace and secure with flat washer and previously removed com nut. Attach other end of Valve Brace to middies soot in rear of Seat Box with 5/16" hex hd cap screw, flat washer, lock washer, and hex nut. See FIG 3. AG.3 1. plash Shield 3.
Qom. FlG. 6 1. Spring Mounting Angle 5. Pump Cover Clamp 2. Pump Pivot Plate 6. Pump Cable 3. Pump Pulley 7. Accessory Control! Lever 4. Pump Belt Cover 8. Pump Spring 10. Remove the hair pin cotter and flat washer from the pin in the Accessory Control Lever. Push the Control Lever down {engaged). Slide the unattached end of the Cable onto the pin and secure with the flat washer and hair pin cotter previously removed. 11.
Barbs and 90° Hose Barb to Tee. Attach Tee to Mounting Bracket using clamp, two (2} 5/16" flat washers, lock washers, and hex nuts, Connect x 67" Overflow Hose from rear of Tank and two x 27 -1/2" Bypass Hoses to Tee, and secure with hose clamps. FG.8 1. Tank Band 3. Tee 2. Clamp 4, Teo Mounting Bracket 11. Connect two (2} x Bypass Hoses o Control Valve. Secure with hose clamps. Route the Suction Hose over the left side of the Vehicle Frame and connect the couplets at the Suction Ball Valve. 12.
Steps 2 and 3 apply to the assembly of the Standard Boom only. If the optional “Boom Pivot Kit' is to be installed, see the instructions furnished with that kit. The Cross Sunspot o be used with that kit is different than the Support used on the Standard Boom. 2. Position the Cross Support Angle and attach it to the Boom Mount Assemblies with two 1/2" x hex hd cap screws and lock nuts. 3. Position the Spacer Tubes between the Boom Mount uprights and the lugs on the Main Frame Tube.
15. Almach three double barb and one single barb Nozzle Assemblies on each Extension Boom Pipe as shown in FIG 13, Nozzles are to be spaced on 20 inch centers. Connect the Nozzle Assemblies with the 3/4* x 19" Jumper Hoses. Secure with hose clamps. LEFT HAND BOOM SHOWN RIGHT HAND BOOM OPPOSITE FIG. 13 1. Boom Support Assembly 5. Single Barb Nozzle Body 2. Extension Boom Pipe 6. Jumper Hose 3. U-obit 7. Boom cap 4, Double Barb Nozzle Body 16. Install the plastic Boom Caps over the ends of the Boom Pipes. 17.
MANUAL VALVE SPRAY SYSTEM PUMP SET—UP. Ref| Part No. Description Qy| Regret Part No.
MANUAL VALVE SPRAYER CONTROL Riel Part No. Description Qty |Re1 Part No, Description Qty| 1 [93-0940 |Adjustment Knob 3| Blvd 1 2 [e-0841 Pin Dia. 4x 20 3 ton O-Ring Dia. 1.78 x 8,75 3 I3 [03-0042 |Lever 3 volumetric Valve Rod 1 |4 93-0943 Upper Valve Body 3 [Spring Pin Dia, O-Ring Dia, 3x 22 7 Outlet Valve Ass'y 3 6 IO-Ring 1, 78 X 7.66 ki Dia. 2.62 x 22.22 3 7 Washer Dia, 8.2 6] Pipe Fitting Dia.
MANUAL SPRAY SYSTEM TANK (MULTI-PRO 1100) Ref| Part No. Description Qty [Ret | Part No. Description Qty 1 [42083 old-In Brace Assembly 2 23 H3068 [Fly Nut, 2" NPT 1 2 [22-12-add [Hex Nut, 5118 NC 8 |24 43087 Sealing Washer.
MANUAL SPRAY VALVE SET-UP Ref {Part No. Description Qty Rite [Part No. Description Ry 141308 [Hose Barb, 1* MPT x H.B. 1 4] 3-0885 [Hose Cover, 1.59" [41327 i Hose Clamp 8 10 193-0881 J Hose Supply, 3-0883 [Hose Bypass to Tank, 67* 1 11 0045 i Hose Clamp & 4 3-0851 |Hose Barb, MPT x HB 2 12 197791 |Boom Feed Hose, RH 124" 1 5 -0886 [Tee, NPT 1 13 193-0884 [Hose Cover, 1.
BOOMS (MULTI-PRO 1100} Ref| Part No. Description Gty Heft Part No.
BOOM FRAME (MULTI-PRO 1100) A CAUTION THE TWO SPRINGS ARE OF 24) LBS, S (REF REF # R REMOVAL OF THE SPIN 150 ( PRESSURE, BE VERY CAUTIOUS WHEN %MOVING THE SPRING PIN UNDER _APPROX. IMPORTANT THE TWO BOLTS (REF # 8) RUED TO 50 FT.
BOOM FRAME (MULTI-PRO 1100) Ref] Part No. Description Qty Ref [Part No. Description Qty 1 142223 [Tube Wedge Says 2 [23* | 24-18-DB [Flat Washer, 1" STAEL. 2 P Re-15-AJAX j Lock Nut, 42196 impression Spring 2 I3 (42225 Ross Support Angle 1 28* ] 42706 Breakaway Pivot Says 2 4 P0-86-AGDHHCS, 12 NC x 2 [26* 1 20-199-C [Spring Pin, 1/4x 2" 2 5 142258 Spacer Tube, Ig. 2, 27 |24-10-BD [Flat Washer, §/16 SAE.
CENTRIFUGAL PUMP (93-0848) Ref| Part No. Description aty Ref| Part No.
