Operator's Manual

ManualsBrandsToro ManualsSnow ThrowerToro 38811

FormNo.3396-496RevA

PowerMax724OESnowthrower

ModelNo.38811—SerialNo.316000001andUp

Operator'sManual

ThisproductcomplieswithallrelevantEuropeandirectives.

Fordetails,pleaseseetheseparateproductspecic

DeclarationofConformity(DOC)sheet.

Introduction

Thismachineisintendedtobeusedbyresidential

homeownersorprofessional,hiredoperators.Itis

designedprimarilyforremovingsnowfrompaved

surfaces,suchasdrivewaysandsidewalks,andother

surfacesfortrafconresidentialorcommercial

properties.Itisnotdesignedforremovingmaterials

otherthansnow,norisamodelwithapivotingscraper

designedforclearingoffgravelsurfaces.

Readthisinformationcarefullytolearnhowtooperateand

maintainyourmachineproperlyandtoavoidinjuryand

machinedamage.Youareresponsibleforoperatingthe

machineproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comformachine

andaccessoryinformation,helpndingadealer,ortoregister

yourmachine.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourmachineready.Figure1identiesthelocationofthe

modelandserialnumbersonthemachine.Writethenumbers

inthespaceprovided.

G016493

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(Figure2),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure2

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanicalinformation

andNoteemphasizesgeneralinformationworthyofspecial

attention.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3396-496*A

Summary of content (28 pages)

PAGE 1
Form No. 3396-496 Rev A Power Max 724 OE Snowthrower Model No. 38811—Serial No. 316000001 and Up Operator's Manual This product complies with all relevant European directives. For details, please see the separate product specific Declaration of Conformity (DOC) sheet. Model No. Serial No. Introduction This machine is intended to be used by residential homeowners or professional, hired operators.
PAGE 2
Contents Introduction .................................................................. 1 Safety ........................................................................... 3 Sound Pressure ....................................................... 3 Sound Power .......................................................... 3 Vibration................................................................ 3 Safety and Instructional Decals ................................. 4 Setup ........................................
PAGE 3
Safety Caution: Improper use may result in loss of fingers, hands, or feet. Before Operating ? ? Read and understand the contents of this manual before operating the snowthrower Become familiar with all controls and know how to stop the engine quickly . . There is a high-speed impeller close to the opening. Operator 's Position The low-speed auger has a moving pinch point close to the opening. Sound Pressure This machine meets or exceeds the ISO standard 8437 in effect at the time of production.
PAGE 4
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 131–6487 1. Engine—stop 3. Fast 2. Slow 121–6817 1. Cutting dismemberment, impeller and cutting dismemberment, auger hazards—keep bystanders a safe distance from the snowthrower. 121–6823 1. Fast 2. Forward speeds 3. Slow 4. Reverse speeds 1 2 x3 3 4 5 121–1239 Order part no. 119–7629 120-9805 120-9805 1. Insert the key. 2. Prime the engine 3 times. 3.
PAGE 5
121–1240 Order part no. 120–7194 1. Traction drive—squeeze the lever to engage; release the lever to disengage. 4. Cutting dismemberment hazard, impeller—keep away from moving parts; remove the ignition key and read the instructions before servicing or performing maintenance. 2. Warning—read the Operator’s Manual. 5. Thrown object hazard—keep bystanders a safe distance from the snowthrower. 6. Auger/impeller drive—squeeze the lever to engage; release the lever to disengage. 3.
PAGE 6
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 Description Use Qty. Handle bolts Curved washers Locknuts Hairpin cotter Flat washer Nut Carriage bolt Flat washer Carriage bolts Locknuts 2 2 2 2 3 2 2 2 2 2 No parts required – Check the engine oil level. No parts required – Check the tire pressure. No parts required – Check the skids. No parts required – Check the operation of the traction drive. Install the upper handle.
PAGE 7
2 Installing the Speed Selector Linkage g019378 Figure 6 Parts needed for this procedure: 2 Hairpin cotter 3 Flat washer 6. Pull up on the speed control rod and insert the trunnion into the hole in the speed selector lever (Figure 5). Note: If the trunnion does not fit into the hole when you lift up on the speed control rod, rotate the trunnion upward or downward on the speed control rod until it fits. Procedure 1.
PAGE 8
3 4 Installing the Chute Installing the Chute Control Rod Parts needed for this procedure: Parts needed for this procedure: 2 Nut 2 Carriage bolt 2 Carriage bolts 2 Flat washer 2 Locknuts Procedure Procedure 1. Remove the blue rod cap from the chute control rod. 1. Place the chute on the frame and the align the discharge chute mount to the chute support. 2.
PAGE 9
the short rod from the left side of the machine (from the operating position). 4. Ensure the chute control operates smoothly. 5 Checking the Engine Oil Level No Parts Required Procedure Your machine comes with oil in the engine crankcase. Note: Before starting the engine, check the oil level and add oil if necessary. Figure 12 Use automotive detergent oil with an API service classification of SF, SG, SH, SJ, SL, or higher. Refer to your engine owner's manual. 2. Install the dipstick securely.
PAGE 10
6. Squeeze the left hand (traction) lever to the hand-grip (Figure 13). 8 The machine should move forward. If the machine does not move or moves rearward, complete the following: Checking the Traction Drive Operation A. Release the traction lever and stop the engine. B. Disconnect the trunnion from the speed selector lever (Figure 5). C. Turn the trunnion upward (counterclockwise) on the speed control rod (Figure 5). D. Connect the trunnion to the speed selector lever (Figure 5).
PAGE 11
Product Overview Figure 16 1. Snow cleanout tool (attached to the handle) Operation Before Operation Safety g018896 • Use extension cords and receptacles as specified by the manufacturer for all machines with electric starting motors. • Do not operate the machine without wearing adequate Figure 14 1. Hand-grip (2) winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear slip resistant footwear that will improve footing on slippery surfaces. 9. Chute deflector 10.
PAGE 12
• Exercise extreme caution when operating on slopes. • Never operate the machine without good visibility or • For best results, use only clean, fresh, unleaded gasoline • • • • • with an octane rating of 87 or higher ((R+M)/2 rating method). Oxygenated fuel with up to 10% ethanol or 15% MTBE by volume is acceptable. Do not use ethanol blends of gasoline (such as E15 or E85) with more than 10% ethanol by volume. Performance problems and/or engine damage may result which may not be covered under warranty.
PAGE 13
To self-propel, insert the axle pins through the holes in the wheel hubs and the inner axle holes (Figure 19). g019014 Figure 19 1 Starting the Engine 1. Check the engine oil level. Refer to Checking the Engine Oil Level in Maintenance. G016498 2. Turn the fuel shutoff valve 1/4 turn counterclockwise to open it (Figure 20). Figure 21 1. Ignition key 4. Firmly push in the primer with your thumb 3 times, holding the primer in for a second before releasing it each time (Figure 22).
PAGE 14
5. Move the choke to the CHOKE position (Figure 23). g019055 Figure 25 1. Electric-starter button 2. Electric starter plug-in 3. Recoil starter Note: To use the electric starter, connect a power cord to the electric starter plug-in first and then to a power outlet. Use only a UL-listed, 16-gauge extension cord recommended for outdoor use that is not longer than 50 feet (15 m). G016501 WARNING Figure 23 The electrical cord can become damaged, causing a shock or fire. 6.
PAGE 15
Operating the Traction Drive engine can also be stopped by pulling the ignition key outward to the middle position. CAUTION If the traction drive is not properly adjusted, the machine may move in the direction opposite of what you intended, causing injury and/or property damage. STOP Carefully check the traction drive and adjust it properly, if necessary; refer to Checking the Traction Drive Operation in Setup for more information.
PAGE 16
Operating the Auger/Impeller Drive 1. To engage the auger/ impeller drive, squeeze the right hand (auger/ impeller) lever to the handgrip (Figure 30). Figure 30 g018897 2. To stop the auger and impeller, release the right hand lever. Figure 31 Important: When you engage both the auger/impeller lever and the traction lever, the traction lever locks the auger/impeller lever down, freeing your right hand. To release both levers, simply release the left hand (traction) lever.
PAGE 17
• After Operation the front of the machine on the pavement. Repeat if necessary until a stream of snow comes out the discharge chute. If you cannot unclog the discharge chute by bumping the front of the machine, stop the engine, wait for all moving parts to stop, and use a stick; never use your hand. Safety • Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water heaters, space heaters, or clothes dryers.
PAGE 18
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 2 hours • Inspect the traction cable and adjust it if necessary. • Inspect the auger/impeller cable and adjust it if necessary. After the first 5 hours • Change the engine oil.
PAGE 19
Preparing for Maintenance 1. Move the machine to a level surface. 2. Stop the engine and wait for all moving parts to stop. 3. Disconnect the spark plug wire. Refer to Replacing the Spark Plug. Checking the Engine Oil Level Service Interval: Before each use or daily—Check the engine oil level and add oil if necessary. 1 1. Remove the dipstick, wipe it clean, then fully install the dipstick. g019046 Figure 34 1. 1/8 inch (3 mm) 2. Remove the dipstick and check the oil level (Figure 33).
PAGE 20
Figure 37 Figure 35 3. Loosen or tighten the turnbuckle to adjust the spring length to 2.75 inches (7 cm) (Figure 38). 3. Loosen or tighten the turnbuckle to adjust the spring length to 2.18 inches (5.5 cm). Figure 38 Figure 36 1. Jam nut 3. Spring 2. Turnbuckle 4. 2.18 inches (5.5 cm) 1. Jam nut 3. Spring 2. Turnbuckle 4. 2.75 inches (7 cm) 4. Tighten the jam nut (Figure 38), ensuring there is slight tension on the cable. 5.
PAGE 21
Engine Oil Capacities Model Engine Oil Capacity 38811 0.50 L (17 oz) 1. Clean the area around the oil drain cap (Figure 41). Figure 39 Figure 41 1. Oil drain cap 3. Remove the pipe plug from the gearbox. 4. Check the oil level in the gearbox. The oil should be 3/8 inch (9.5 mm) below the filler opening. 2. Slide an oil drain pan under the drain extension and remove the oil drain cap. 5.
PAGE 22
Storage 2. Remove any slack in the cable by pulling the cable conduit rearward. 3. Tighten the clamp fastener while holding the cable in place. WARNING • Gasoline vapors can explode. • Do not store gasoline more than 30 days. • Do not store the machine in an enclosure near an open flame. • Allow the engine to cool before storing it. Replacing the Drive Belts If the auger/impeller drive belt or the traction drive belt becomes worn, oil-soaked, or otherwise damaged, go to www.Toro.
PAGE 23
Removing the Machine from Storage 1. Remove the spark plug and spin the engine rapidly using the starter to blow the excess oil from the cylinder. 2. Install the spark plug by hand and then torque it to 15 ft-lb (20.4 N-m). 3. Connect the spark plug wire. 4. Perform the annual maintenance procedures as given in the Recommended Maintenance Schedule.
PAGE 24
Troubleshooting Problem The electric starter does not turn (electric-start models only). The engine does not start or starts hard. Possible Cause 1. The power cord is disconnected at the outlet or the machine. 1. Connect the power cord to the outlet and/or the machine. 2. The power cord is worn, corroded, or damaged. 3. The power outlet is not energized. 2. Replace the power cord. 3. Have a qualified electrician energize the outlet. 1. The key is not in the ignition or is in the Stop position. 1.
PAGE 25
Problem The engine runs, but the machine discharges snow poorly or not at all. Possible Cause Corrective Action 1. The throttle is not in the Fast position when throwing snow. 1. Move the throttle to the Fast position. 2. The machine is moving too fast to clear the snow. 3. You are trying to remove too much snow per swath. 4. You are trying to remove extremely heavy or wet snow. 5. The discharge chute is plugged. 6. The auger/impeller drive belt is loose or is off the pulley. 2.
PAGE 26
Notes: 26
PAGE 27
International Distributor List Distributor: Agrolanc Kft Asian American Industrial (AAI) B-Ray Corporation Brisa Goods LLC Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co. Fat Dragon Femco S.A. FIVEMANS New-Tech Co., Ltd ForGarder OU G.Y.K. Company Ltd. Geomechaniki of Athens Golf international Turizm Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irrimac Irrigation Products Int'l Pvt Ltd.
PAGE 28
Residential Snow Products The Toro Warranty and The Toro GTS Starting Guarantee Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair for the original purchaser1 the Toro Product listed below if defective in materials or workmanship or if the Toro GTS (Guaranteed to Start) engine will not start on the first or second pull, provided the routine maintenance required in the Operator's Manual have been perform