Operator's Manual

ManualsBrandsToro ManualsSnow ThrowerToro 38633

FormNo.3370-519RevA

PowerMaxSnowthrower

ModelNo.38597—SerialNo.312000001andUp

ModelNo.38629—SerialNo.312000001andUp

ModelNo.38633—SerialNo.312000001andUp

ModelNo.38637—SerialNo.312000001andUp

ModelNo.38639—SerialNo.312000001andUp

ModelNo.38657—SerialNo.312000001andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeownersorprofessional,hiredoperators.It

isdesignedprimarilyforremovingsnowfrom

pavedsurfaces,suchasdrivewaysandsidewalks,

andothersurfacesfortrafconresidentialor

commercialproperties.Itisnotdesignedfor

removingmaterialsotherthansnow,norisamodel

withapivotingscraperdesignedforclearingoff

gravelsurfaces.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourmachineproperlyandtoavoidinjury

andmachinedamage.Youareresponsibleforoperating

themachineproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comfor

machineandaccessoryinformation,helpndinga

dealer,ortoregisteryourmachine.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourmachineready.

Figure1

identiesthelocationofthemodelandserialnumbers

onthemachine.Writethenumbersinthespace

provided.

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafetyalertsymbol

(

Figure2),whichsignalsahazardthatmaycauseserious

injuryordeathifyoudonotfollowtherecommended

precautions.

Figure2

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

ReplacementEngineOwner’sManualsmaybe

orderedthroughtheenginemanufacturer.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (32 pages)

PAGE 1
Form No. 3370-519 Rev A Power Max Snowthrower Model No. 38597—Serial No. 312000001 and Up Model No. 38629—Serial No. 312000001 and Up Model No. 38633—Serial No. 312000001 and Up Model No. 38637—Serial No. 312000001 and Up Model No. 38639—Serial No. 312000001 and Up Model No. 38657—Serial No. 312000001 and Up Operator's Manual Introduction Model No. This machine is intended to be used by residential homeowners or professional, hired operators.
PAGE 2
Safety Caution: Improper use may result in loss of fingers, hands, or feet. Before Operating ? ? Read and understand the contents of this manual before operating the snowthrower Become familiar with all controls and know how to stop the engine quickly . . There is a high-speed impeller close to the opening. Operator 's Position The low-speed auger has a moving pinch point close to the opening. Preparation This machine meets or exceeds the ISO standard 8437 in effect at the time of production.
PAGE 3
wear safety glasses or eye shields during operation or while performing an adjustment or repair. • Never operate the machine without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run. Operation • Never operate the machine without good visibility or light. • Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
PAGE 4
Safety and Instructional Decals • If a shield, safety device, or decal is damaged, illegible, or lost, repair or replace it before beginning operation. Also, tighten any loose fasteners. • Do not smoke while handling gasoline. • Do not use the machine on a roof. • Do not touch the engine while it is running or soon after it has stopped because the engine may be hot enough to cause a burn. • Perform only those maintenance instructions described in this manual.
PAGE 5
112-6625 Reorder part no. 112-6629 1. Cutting/dismemberment hazard, impeller—do not place your hand in the chute; stop the engine before leaving the operator’s position, use the tool to clear the chute. 112-6626 1. Traction drive—squeeze the lever to 5. Thrown object hazard—keep 3. Cutting/dismemberment hazard, engage; release the lever to disengage. bystanders a safe distance from the impeller—do not place your hand in the machine.
PAGE 6
Briggs & Stratton Part No. 273676 3. Fast 1. Stop 2. Slow Briggs & Stratton Part No. 277588 1. Primer Briggs & Stratton Part No. 275949 1. Choke on (Choke) 2. Choke off (Run) 3. Ignition key out (Engine—Stop) 2. Ignition key in (Engine—Run) Briggs & Stratton Part No. 276925 1. Warning—read the Operator’s Manual. 2. Warning—fire hazard. 3. Warning—toxic gas inhalation hazard. 4. Warning—hot surface/burn hazard. Briggs & Stratton Part No. 278866 1. Fuel—On Briggs & Stratton Part No. 277566 1.
PAGE 7
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 Description Use Qty. Handle bolts Curved washers Locknuts 4 4 4 Install the upper handle. No parts required – Install the wheel clutch cable ends No parts required – Install the traction control linkage. Carriage bolts Locknuts 2 2 Install the chute control rod. Cable tie 1 Connect the wire to the headlight. No parts required – Fill the engine with oil.
PAGE 8
Figure 6 1. Wheel clutch lever 3. Remove the nut and washer from the handle, attach the cable clamp on the cable to the handle, install the washer and the nut, and hand tighten the nut (Figure 7). Figure 4 2 Installing the Wheel Clutch Cable Ends No Parts Required Figure 7 1. Cable clamp (2) Procedure Models 38633, 38637, and 38657 only Important: Ensure that the curved side of the cable clamp is against the handle and that the cable is routed below the clamp bolt.
PAGE 9
Figure 9 Note: The gap should be approximately the thickness of a pencil (1/4 inch or 6 mm). If it is greater, loosen the cable clamp nut, slide the cable jacket up slightly, tighten the cable clamp nut, and check the gap again. Figure 11 1. Speed selector lever 2. Trunnion 6. Repeat steps 2 through 5 for the other cable. 3. Inner washer 4. Outer washer Note: To make installation easier, leave the flat washer on the trunnion (Figure 11). 3 4. Shift the speed selector lever into Position R2. 5.
PAGE 10
Note: For easier installation, look down through the opening in the speed selector (Figure 13). Figure 14 Figure 13 1. Short rod 1. Speed selector 2. Long chute control rod 4. Insert the front end of the rod into the opening in the back of the chute gear cover until it slides into the chute gear (Figure 15). 4 Installing the Chute Control Rod Parts needed for this procedure: 2 Carriage bolts 2 Locknuts Procedure 1. Unwrap the Quick Stick and rotate it so that it is upright and in the center.
PAGE 11
Note: Ensure that the plastic clip on the wire connector is on the bottom (Figure 17). 2. Secure a cable tie (from the loose parts bag) around the wire and the handle about an inch (2.5 cm) below the U-bolt (Figure 17). 6 Figure 16 1. Cable clip 2. Deflector cable Filling the Engine with Oil 7. Hold the blue trigger cap down and rotate the Quick Stick in a circle to ensure that the chute and deflector operate smoothly.
PAGE 12
Engine Oil Capacities (cont'd.) Model Engine Oil Capacity 38597 18 to 20 oz. (0.53 to 0.59 l) 8 Checking the Skids 38629 38633 No Parts Required 38637 38639 38657 Procedure 26 to 28 oz. (0.77 to 0.83 l) Refer to Checking and Adjusting the Skids in Maintenance. 1. Remove the dipstick and slowly pour oil into the oil fill tube to raise the oil level to the Full mark on the dipstick. Do not overfill (Figure 19). Refer to Checking the Engine Oil Level in Maintenance.
PAGE 13
Product Overview A. Release the traction lever and stop the engine. B. Disconnect the trunnion from the speed selector lever (Figure 11). C. Turn the trunnion downward (clockwise) on the speed control rod (Figure 11). D. Connect the trunnion to the speed selector lever (Figure 11). 4. Release the traction lever. 5. Move the speed selector to the Position 1; refer to Operating the Speed Selector. 6. Squeeze the left hand (traction) lever to the hand-grip (Figure 20). The machine should move forward.
PAGE 14
Filling the Fuel Tank DANGER Gasoline is extremely flammable and explosive. A fire or explosion from gasoline can burn you and others. Figure 23 1. Snow cleanout tool (attached to the handle) • To prevent a static charge from igniting the gasoline, place the container and/or machine on the ground before filling, not in a vehicle or on an object. Operation Note: Determine the left and right sides of the machine from the normal operating position. • Fill the tank outdoors when the engine is cold.
PAGE 15
Starting the Engine 1. Check the engine oil level. Refer to Checking the Engine Oil Level in Maintenance. 2. Turn the fuel shutoff valve 1/4 turn counterclockwise to open it (Figure 27). Figure 27 3. Insert the ignition key (Figure 28). Figure 29 5. Rotate the choke to the Choke position (Figure 30). Figure 30 Figure 28 1. Ignition key 6. Move the throttle to the Fast position (Figure 31). 4.
PAGE 16
Stopping the Engine 7. Start the machine pulling the recoil starter or pressing the electric-starter button (all models except 38597) (Figure 32). 1. Move the throttle to the Slow position, and then to the Stop position (Figure 33). Figure 33 Figure 32 1. Electric-starter button (all models except 38597) 2. Electric starter plug (all models except 38597) 3. Recoil starter 2. Wait for all moving parts to stop before leaving the operating position. 3. Remove the ignition key.
PAGE 17
Operating the Traction Drive Using the Wheel Clutch Levers Models 38637 and 38657 only CAUTION The wheel clutch levers allow you to momentarily disengage the drive to one or both wheels with the traction drive lever still engaged. This enables you to turn and maneuver the machine easily. If the traction drive is not properly adjusted, the machine may move in the direction opposite of what you intended, causing injury and/or property damage.
PAGE 18
Operating the Speed Selector WARNING If the auger and impeller continue to rotate when you release the auger/impeller lever, you could seriously injure yourself or others. The speed selector has 6 forward and 2 reverse gears. To change speeds, release the traction lever and shift the speed selector lever to the desired position (Figure 38). The lever locks in a notch at each speed selection. Do not operate the machine. Take it to an Authorized Service Dealer for service.
PAGE 19
Preventing Freeze-up • If the chute does not move, refer to Adjusting the Discharge Chute Latch. • If the chute does not turn as far to the left as it does to the right, ensure that the cable is routed to the inside of the handles. Refer to Installing the Upper Handle. • If the chute does not lock into place when you release the trigger cap, refer to Adjusting the Discharge Chute Latch. • In snowy and cold conditions, some controls and moving parts may freeze.
PAGE 20
• If the engine slows down under a load or the wheels slip, shift the machine into a lower gear. if you must use the machine on a gravel surface, adjust the skids further down to prevent the pivoting scraper from picking up rocks. • If the front of the machine rides up, shift the machine into a lower gear. If the front continues to ride up, lift up on the handles. • The pivoting scraper on the machine is not recommended for use on gravel surfaces.
PAGE 21
Preparing for Maintenance 1. Move the machine to a level surface. 2. Stop the engine and wait for all moving parts to stop. 3. Disconnect the spark plug wire. Refer to Replacing the Spark Plug. Figure 44 Checking the Engine Oil Level 1. 1/2 inch (1.3 cm) Service Interval: Before each use or daily—Check the engine oil level and add oil if necessary. 3. Support the side plates so that they are at least 1/2 inch (1.3 cm) above a level surface. 1.
PAGE 22
Checking and Adjusting the Traction Cable Service Interval: After the first 2 hours—Inspect the traction cable and adjust it if necessary. Yearly—Inspect the traction cable and adjust or replace it if necessary. Figure 45 1. Skid If the machine does not drive in the forward or reverse speeds or it drives when you release the traction lever, adjust the traction cable. 4.
PAGE 23
Checking the Auger Gearbox Oil Level Service Interval: Yearly—Check the auger gearbox oil and add oil if necessary. 1. Move the machine to a level surface. 2. Clean the area around the pipe plug (Figure 49). Figure 50 1. Using SAE 30 at outdoor temperatures below 40°F (4°C) will result in hard starting. Figure 49 2. Using 10W-30 at outdoor temperatures above 80°F (27°C) may result in increased oil consumption; therefore, check the oil level more frequently in these circumstances.
PAGE 24
Adjusting the Discharge Chute Latch Note: The latch is spring loaded and will naturally move into the teeth of the gear (Figure 54). 4. Remove any slack in the cable by pulling the cable conduit rearward. If the discharge chute does not lock into the desired position or does not unlock so that you can move it to another position, adjust the discharge chute latch. 1. Remove the fastener on the gear cover (Figure 52), lift the front of the cover up, and slide it back and out of the way. 5.
PAGE 25
Storage WARNING • Gasoline vapors can explode. • Do not store gasoline more than 30 days. • Do not store the machine in an enclosure near an open flame. • Allow the engine to cool before storing it. Figure 57 4. Insert a new bulb into the back of the headlight (Figure 58). Preparing the Machine for Storage 1. On the last refueling of the year, add fuel stabilizer to fresh fuel as directed by the engine manufacturer. 2.
PAGE 26
17. Tighten all loose screws, bolts, and locknuts. Repair or replace any damaged parts. 18. Cover the machine and store it in a clean, dry place out of the reach of children. Allow the engine to cool before storing it in any enclosure. Removing the Machine from Storage 1. Remove the spark plug and spin the engine rapidly using the starter to blow the excess oil from the cylinder. 2. Install the spark plug by hand and then torque it to 15 ft-lb (20.4 N-m). 3. Connect the spark plug wire. 4.
PAGE 27
Troubleshooting Problem Possible Cause Electric starter does not turn (electric-start models only) 1. The power cord is disconnected at the outlet or the machine. 1. Connect the power cord to the outlet and/or the machine. 2. The power cord is worn, corroded, or damaged. 3. The power outlet is not energized. 2. Replace the power cord. 1. The key is not in the ignition or is in the Stop position. 1. Insert the key into the ignition and turn it to the On position. 2.
PAGE 28
Problem Possible Cause Corrective Action 7. The auger/impeller drive belt is worn or broken. 7. Replace the auger/impeller drive belt; refer to www.Toro.com for servicing information or take the machine to an Authorized Service Dealer. Discharge chute either does not lock into place or does not move 1. The discharge chute latch is not properly adjusted. 1. Adjust the discharge chute latch. The machine does not properly clear the snow off the surface 1.
PAGE 29
Notes: 29
PAGE 30
Notes: 30
PAGE 31
International Distributor List Distributor: Atlantis Su ve Sulama Sisstemleri Lt Balama Prima Engineering Equip. B-Ray Corporation Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Equiver Femco S.A. G.Y.K. Company Ltd. Geomechaniki of Athens Guandong Golden Star Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Ibea S.P.A. Irriamc Irrigation Products Int’l Pvt Ltd. Jean Heybroek b.v. Lely (U.K.
PAGE 32
The Toro Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Product listed below if used for residential purposes* if defective in materials or workmanship. Instructions for Obtaining Warranty Service If you think that your Toro Product contains a defect in materials or workmanship, follow this procedure: 1. Contact your seller to arrange service of the product.