Operator's Manual

ManualsBrandsToro ManualsOutdoorsPower Clear 518 ZR 18 in. Single-Stage Gas Snow Blower

FormNo.3432-459RevA

PowerClear

518Snowthrower

ModelNo.38472—SerialNo.404621000andUp

ModelNo.38473—SerialNo.404621000andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeowners.Itisdesignedprimarilyforremoving

snowfrompavedsurfaces,suchasdrivewaysand

sidewalks,andothersurfacesfortrafconresidential

orcommercialproperties.Itisnotdesignedfor

removingmaterialsotherthansnow,norisitdesigned

forclearinggravelsurfaces.Usingthisproductfor

purposesotherthanitsintendedusecouldprove

dangeroustoyouandbystanders.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Visitwww.Toro.comforproductsafetyandoperation

trainingmaterials,accessoryinformation,helpnding

adealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

Important:Withyourmobiledevice,youcan

scantheQRcodeontheserialnumberdecal(if

equipped)toaccesswarranty,parts,andother

productinformation.

g293191

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedinMexico

AllRightsReserved

*3432-459*A

Summary of content (20 pages)

PAGE 1
Form No. 3432-459 Rev A Power Clear® 518 Snowthrower Model No. 38472—Serial No. 404621000 and Up Model No. 38473—Serial No. 404621000 and Up Operator's Manual Introduction Model No. This machine is intended to be used by residential homeowners. It is designed primarily for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties.
PAGE 2
Contents Important: If you are using this machine above 1500 m (5,000 ft) for a continuous period, ensure that the High Altitude Kit has been installed so that the engine meets CARB/EPA emission regulations. The High Altitude Kit increases engine performance while preventing spark-plug fouling, hard starting, and increased emissions. Once you have installed the kit, attach the high-altitude label next to the serial decal on the machine.
PAGE 3
Safety This machine has been designed in accordance with ANSI/OPEI B71.3 specifications. General Safety This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury. • Read and understand the contents of this Operator’s Manual before you start the engine. Ensure that everyone using this product knows how to use it, knows how to shut off the engine quickly, and understands the warnings.
PAGE 4
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal120-0149 120-0149 1. Primer 4. Pull the key to switch the engine switch off. 117-6047 2. Push the primer 2 times to prime the engine. 5. Remove the key to lock the machine. 1.
PAGE 5
Setup 1 Installing the Handle No Parts Required Procedure g253607 2 Installing the Discharge Chute No Parts Required Procedure g255436 5
PAGE 6
3 Installing the Recoil-Start Handle No Parts Required Procedure g253609 4 Filling the Engine with Oil No Parts Required Procedure g253610 6
PAGE 7
5 Adjusting the Control Cable No Parts Required Procedure Refer to Checking and Adjusting the Control Cable (page 15).
PAGE 8
Specifications Product Overview Model 38472 38473 Weight Length Width Height 24.5 kg (54 lb) 94 cm 48 cm 114 cm 26.3 kg (37 inches) (19 inches) (45 inches) (58 lb) Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories.
PAGE 9
Filling the Fuel Tank Operation • For best results, use only clean, fresh (less than Note: Determine the left and right sides of the 30 days old), unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). machine from the normal operating position. • Oxygenated fuel with up to 10% ethanol or 15% MTBE by volume is acceptable. Before Operation • Do not use ethanol blends of gasoline (such as E15 or E85) with more than 10% ethanol by volume.
PAGE 10
Checking the Engine-Oil Level Service Interval: Before each use or daily g293231 Figure 11 During Operation • When not actively clearing snow, disengage power During Operation Safety • Exercise extreme caution when operating the to the auger. machine on walks or roads. Stay alert for hidden hazards or traffic. General Safety • Never attempt to make any adjustments while • Shut off the engine before unclogging the • • • • • • • • the engine is running, except as directed in the instructions.
PAGE 11
Starting the Engine Electric-Start Model Note: Remove your glove when you push in the primer so that air cannot escape from the primer hole. Important: Do not use the primer or the choke if the engine has been running and is hot. Excessive priming may flood the engine and prevent it from starting. To use the electric starter (electric-start models only), connect a power cord to the electric-start plug-in first and then to a ground fault circuit interrupter (GFCI) power outlet.
PAGE 12
g253666 Figure 13 Engaging the Rotor Blades Disengaging the Rotor Blades To engage the rotor blades, hold the control bar against the handle (Figure 14). To disengage the rotor blades, release the control bar (Figure 15).
PAGE 13
Shutting Off the Engine To shut off the engine, pull the ignition key outward until it clicks into the OFF position (Figure 16) or move the choke lever fully to the right (B of Figure 13). g011581 Figure 18 1. Trigger 2. Chute deflector Clearing a Clogged Discharge Chute g013828 Figure 16 To clear the chute: 1. Ignition key • Shut off the engine. • Wait 10 seconds to ensure that the rotor blades have stopped rotating.
PAGE 14
scraper lifts off the ground and snow escapes behind the machine. wait for all moving parts to stop, and remove ice and snow from the machine. • Clean off any snow and ice from the base of the Operating Tips chute. • Rotate the discharge chute left and right to free it from any ice buildup. WARNING • With the key removed, pull the recoil-start handle The rotor blades can throw stones, toys, and other foreign objects and cause serious personal injury to you or bystanders.
PAGE 15
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval After the first hour After the first 2 hours Before each use or daily Yearly Yearly or before storage Maintenance Procedure • Check the control cable and adjust it if necessary. • Check for loose fasteners and tighten them if necessary. • Change the engine oil. • Check the engine-oil level and add oil if necessary. • Check the control cable and adjust it if necessary.
PAGE 16
g011544 Figure 22 1. The wear-indicator hole is intact; you do not need to replace the rotor blades. g006402 Figure 21 1. Adjuster link 3. Spring cover 2. Z-fitting 4. Unhook the spring here. Changing the Engine Oil Service Interval: After the first 2 hours Yearly Note: You can pull up the adjuster link and cable to make unhooking the spring easier. 2. If possible, run the engine for a few minutes before changing the oil to warm it. Warm oil flows better and carries more contaminants.
PAGE 17
Note: To determine the proper oil level on the dipstick, refer to Figure 23. 11. With the machine in the operating position, insert the dipstick into the oil-fill tube, but do not screw it in, then remove the dipstick. 12. Read the oil level on the dipstick. • If the oil level on the dipstick is too low, carefully pour a small amount of oil into the oil-fill tube, wait 3 minutes, and repeat steps 10 through 12 until the oil level on the dipstick is correct.
PAGE 18
Replacing the Drive Belt If drive belt becomes worn, oil-soaked, excessively cracked, frayed, or otherwise damaged, replace the belt. 1. Remove the 4 bolts that hold the drive-belt cover (Figure 26) in place. g011642 Figure 27 1. Belt guide 2. Engine pulley Note: Do not distort or damage the belt guide. 6. To install the new drive belt, reverse the steps above.
PAGE 19
Storage Storage Safety • Shut off the engine, remove the key, and wait for all movement to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it. • Fuel fumes are highly flammable, explosive, and dangerous if inhaled. If you store the product in an area with an open flame, the fuel fumes may ignite and cause an explosion.
PAGE 20
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.