MODEL NO. 38191 & UP MODEL NO. 38196 & UP FORM NO. 3320-580 OPERATOR’S MANUAL CCR 1000”" SNOW THROWER INSTRUCTIONS To ensure maximum safety, best performance, and to gain knowledge of the product, R is essential that rower read and understand the contents of this manual before the motor is ever started. Pay particular attention to the safety alert symbol ) which means CAUTION, WARNING OR DANGER — “personal safety instruction” Read and understand the Instruction because it has 10 do with safety.
SAFEWAY INSTRUCTIONS 17. DO NOT USE SNOW THROWER ON A ROOF. 18. Do not overload the snow thrower by clearing snow at too fast a rate. 19. Never operate snowblower at high transport speeds on slippery surfaces. 20. Use extreme caution when crossing or operating snowblower on wanks, roads, grave! or crushed rock drives. Refer to Operating Instructions, page 7, item 4 for correct operating procedure, 21.
A\ SAFETY SYMBOL GLOSSARY Safety decals and Instructions are easily visible 1o the operator and are located near any area of potential danger. Replace any decal that Is damaged. bt TH b Rotor drive~Engaged Rotor drive — Disengaged Whenever you leave the operating position, stop engine by turning key to OFF \ l. ,} s\ Shut off engine before unclogging discharge chute Az @ Stop engine to adjust, unclog or remove debris 4 pb Av old Injury from rotating auger by keeping hands, feet, and clothing away.
ASSEMBLY INSTRUCTIONS Note: Determine left and right sides of snow thrower by standing in the normal operating position. INSTALL WHEELS (Fig. 1) 1. Place a wood block under the wheel axis for support. Figure 1 1. Hatsheput 2. Spacer 3, Axle 2. Slide a spacer and wheel onto the axle. The side of the wheal with six spokes must face the center of the axis. Slide a push nut onto the end of the axle. 3. Using a hammer, strike the push nut o seat the nut firmly in place.
ASSEMBLY INSTRUCTIONS 3. Secure right side of handier with (2) machine screws. Secure left side of handle with (1) machine screw, (1} eye bolt, and a spacer. Use the eyeball to mount upper left side of handle. Insert the eye bolt through the spacer before using it 1o secure handle to the snow thrower frame. The eye bolt must be positioned perpendicular 1o handier when lightened. INSTALL CONTROL CABLE (Fig. 4-5) 1. Route control cable through eye bolt on left side of snow thrower. 2.
BEFORE OPERATING DANGER: Gasoline is extremity flammable and explosive under certain conditions. Do not smoke when handing fuel and keep fuel far away from open flames and sparks. Never buy mote than & 30 day supply of gasoline. Store it in an approved container. Keep gasoline out of the reach of children. Refuel outdoors and only when engine is cold. Do not fife tank full. Fief tank to just below bottom of filler neck, not into the filler neck. This space Is for expansion of fuel.
OPERATING INSTRUCTIONS STARTING/STOPPING ENGINE (Fig. 7) 1. CONTROLS—Key switch, primer, dyslectic sitar button, and recoil starter are located on the control panel. The choke lever is just below the lower left corner of the control panel. 2. Tum key to ON and move choke lever to ON (far right position). 3.
OPERATING INSTRUCTIONS §. In some snow and cold weather conditions, some controls and moving parts may freeze solid. DO NOT USE EXCESSIVE FORCE WHEN TRYING TO OPERATE FROZEN CONTROLS. When any control or pant becomes hard to operate, start the engine and let it rur for a few minutes. If control or part still will not move with moderate force, stop engine, remove ice or thaw out snowblower. €. AFTER CLEARING engine run for a few minutes 80 ice does not freeze moving parts solid.
MAINTENANCE REPLACING SCRAPER (Fig. 11-12) Before each season, inspect scraper for west. If thickness of bottom of scraper is less than 1/16” (1.6 ram), replace scraper (Fig. 11). A 116” Figure 11 1. Soc raper 1. Tum ignition key ta OFF. 2. Drain gasoline from tel tank; refer to Draining Gasoline, page 8. 3. Tip snow thrower forward onto nose. 4. Remove (3) carriage bolts and (3) flange nuts holding scraper in place {Fig. 12). Remove scraper. 4.
MAINTENANCE REPLACING SPARK PLUG (Fig. 15-17) Be tore each snow season, check the spark pig. 1f electrodes in center of plug are dark or have deteriorated, install a new plug. Use a Champion CABBY spark plug and set gap at .030" (.76 mmj. 1. REMOVE CONTROL PANEL (Fig. {2) screws securing control pane to housing. Remove ignition key and lift off pane, allowing it to hang on recoil rope. Figure 15 1. Control panes 2. Cap screws 2. REMOVE SPARK PLUG {Fig. 16)— Pull wire off spark plug and remove pig.
MAINTENANCE ADJUSTING CARBURETOR The carburetor has been factory set, and no adjustment is required. However, when operating snow thrower at altitudes of 5000 feet above sea level or higher, carburetor jets may have to be changed. Contact your local Authorized Toto Service Dealer for assistance. STORING SNOW THROWER 1. For long term storage, either drain gasoline from fuel tank of use a fuel stabilizer before storing. To drain gasoline, refer to Draining Gasoline, page 8.
