Operator's Manual
The fuel system must be bled if any of
the following situations have occurred:
A. Initial start up of a new machine.
B. Engine has ceased running due to lack of fuel.
C. Maintenance has been performed upon fuel
system components; i.e. filter replaced,
separator serviced, and so on.
Refer to Bleeding Fuel System.
Ensure parking brake is set, PTO lever is in OFF
position, and lift lever is in TRANSPORT or FLOAT
position. Remove foot from traction pedal and insure it
is in neutral.
Move throttle control to full FAST position.
Push glow plug switch to ON position and hold
until indicator glows red. Continue to hold switch in
position for suggested interval and turn key in key
switch to START position. Release glow plug switch
after engine starts and allow key to return to RUN
position. Move throttle control to SLOW position.
/3% / ./3 %7#%%$ -).43% /& #/.3).4/42 42% /1
',/6 0,4' -!8 &!), 01%-!341%,8
/3% Refer to chart indicating approximate preheat
time suggested in various temperature ranges.
%-0%1!341%
Above 41F(5C)
1%(%!3 3)-% 2%#
23Fto 41F
Below 23F (Ć5C)
10
20
30
/3% / ./3 14. 23!13%1 -/3/1 -/1% 3(!.
2%#/.$2 !3 ! 3)-% /1 01%-!341% 23!13%1 &!),41% -!8
1%24,3 & %.').% &!),2 3/ 23!13 !&3%1 2%#/.$2 341.
+%8 3/ 0/2)3)/. 1%#(%#+ #/.31/,2 !.$
01/#%$41%2 6!)3 !$$)3)/.!, 2%#/.$2 !.$ 1%0%!3
23!13%1 01/#%$41%
Turn key in key switch to START position. Release
key immediately when engine starts and allow it to
return to RUN position. Move throttle control to SLOW
position.
(43 %.').% /&& !.$ 6!)3 &/1 !,, -/5).' 0!132 3/
23/0 "%&/1% #(%#+).' &/1 /), ,%!+2 ,//2% 0!132
/1 /3(%1 $)&&)#4,3)%2
When engine is started for the first time, or after
overhaul of the engine, transmission or axle, operate
the machine in forward and reverse for one or two
minutes. Also operate the lift lever and PTO lever to
assure proper operation of all parts. Turn steering
wheel to the left and right to check steering response.
Then shut engine off and check for oil leaks, loose
parts, and any other noticeable difficulties.
To stop engine, move throttle control backward to
SLOW position, move PTO lever to OFF position, and
rotate ignition key to OFF. Remove key from switch to
prevent accidental starting.
Unlatch and raise hood over engine.
Loosen air bleed screw on top of fuel filter/water
separator (Fig. 32).
)'41%
4%, &),3%16!3%1 2%0!1!3/1
,%%$ 2#1%6
Turn key in ignition switch to the RUN position.
Electric fuel pump will begin operation, thereby forcing
air out around air bleed screw. Leave key in RUN
position until solid stream of fuel flows out around
screw. Tighten screw and tun key to OFF.
Open the air bleed screw on the fuel injection
pump (Fig. 33) with a 12 mm wrench.
)'41%
4%, ).*%#3)/. 04-0
)1 ",%%$ 2#1%6