Operator's Manual

3
Changing the Hydraulic System Fluid 48. . . . . . . . . .
Changing Rear Axle Lubricant 49. . . . . . . . . . . . . . .
Checking Steering Cylinder Bolt Torque
(Models 30627 & 30631 only) 49. . . . . . . . . . . . . .
Changing Bidirectional Clutch Lubricant
(Models 30627 & 30631 only) 50. . . . . . . . . . . . . .
Fuses 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Servicing the Battery 50. . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Schematic
(Models 30627 & 30631 only) 51. . . . . . . . . . . . . .
Hydraulic Schematic
(Models 30626 & 30630 only) 52. . . . . . . . . . . . . .
Electrical Schematic
(Models 30627 & 30631 only) 53. . . . . . . . . . . . . .
Electrical Schematic
(Models 30626 & 30630 only) 54. . . . . . . . . . . . . .
Seasonal Storage 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Traction Unit 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Toro General Commercial Products Warranty 56. . .
Introduction
Read this manual carefully to learn how to operate and
maintain your product properly. The information in this
manual can help you and others avoid injury and product
damage. Although Toro designs and produces safe
products, you are responsible for operating the product
properly and safely.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and
serial numbers of your product ready. Figure 1 illustrates
the location of the model and serial numbers on the
product.
1
Figure 1
1. Location of the model and serial numbers
Write the product model and serial numbers in the space
below:
Model No.
Serial No.
This manual identifies potential hazards and has special
safety messages that help you and others avoid personal
injury and even death. Danger, Warning, and Caution are
signal words used to identify the level of hazard. However,
regardless of the hazard, be extremely careful.
Danger signals an extreme hazard that will cause serious
injury or death if you do not follow the recommended
precautions.
Warning signals a hazard that may cause serious injury or
death if you do not follow the recommended precautions.
Caution signals a hazard that may cause minor or moderate
injury if you do not follow the recommended precautions.
This manual uses two other words to highlight information.
Important calls attention to special mechanical
information and Note: emphasizes general information
worthy of special attention.
Safety
Models 30630 and 30631 meet or exceed CEN standard
EN 836:1997, ISO standard 5395:1990, and ANSI
B71.4-1999 specifications in effect at the time of
production, when weights are installed according to
chart on page 24.
Models 30626 and 30627 meet or exceed the B71.4 1999
specifications of the American National Standards
Institute, in effect at time of production, when weights
are installed according to chart on page 24.
Note: The addition of attachments made by other
manufacturers that do not meet American National
Standards Institute certification will cause noncompliance
of this machine.
Improper use or maintenance by the operator or owner
can result in injury. To reduce the potential for injury,
comply with these safety instructions and always pay
attention to the safety alert
symbol, which means
CAUTION, WARNING, or DANGER—“personal
safety instruction.” Failure to comply with the
instruction may result in personal injury or death.