FORM NO. 3317–979GB Rev. A ProLine Mid-Size 12.5 HP Traction Unit Model No. 30165 – 690001 & Up Operator’s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety of others. Also become familiar with the controls and their proper use before you operate the product.
Introduction Thank you for purchasing a Toro product. All of us at Toro want you to be completely satisfied with your new product, so feel free to contact your local Authorized Service Dealer for help with service, genuine replacement parts, or other information you may require. Whenever you contact your Authorized Service Dealer or the factory, always know the model and serial numbers of your product.
Contents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slope Chart . . . . . . . . . . . . . . . . . . . . . . . . . Symbols Glossary . . . . . . . . . . . . . . . . . . . Gasoline and Oil . . . . . . . . . . . . . . . . . . . . . . . . Recommended Gasoline . . . . . . . . . . . . . . . Stabilizer/Conditioner . . . . . . . . . . . . . . . . Filling the Fuel Tank . . . . . . . . . . . . . . . . . Check Engine Oil Level . . . . . . . . . . . . . . . Set-up . . . . . . . . . . . . .
Safety Training 4. Replace faulty silencers. 1. Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. 5. 2. Never allow children or people unfamiliar with these instructions to use the lawnmower. Local regulations may restrict the age of the operator. Before using, always visually inspect to see that the blades, blade bolts and cutter assembly are not worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance. 6.
Safety 13. Disengage all blade and drive clutches before starting the engine. Maintenance and storage 1. Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. 2. Never store the equipment with petrol in the tank inside a building where fumes may reach an open flame or spark. 3. Allow the engine to cool before storing in any enclosure. 4.
Safety Slope Chart Read all safety instructions on pages 2–7.
Safety Symbols Glossary Safety alert triangle– symbol within triangle indicates a hazard Fire, open light & smoking prohibited Safety alert symbol Fire or open flame Read operator’s manual Consult technical manual for proper service procedures Shut off engine & remove key before preforming maintenance or repair work Explosion Do not dispose of lead battery in garbage Stay a safe distance from the machine Caustic liquids, chemical burns to fingers or hand Stay safe distance from machine Caution,
Safety Symbols Glossary Do not open or remove safety shields while engine is running Machine rollover, riding mower Thrown or flying objects, whole body exposure To operate machine on a slope, use with 16kg weight kit & operate with deck lowered Thrown or flying objects, whole body exposure Stop engine before leaving operator position Keep guards and safety sheilds in place Machine being transported Severing of toes & fingers, rotary mower blade Blade cutting elementheight adjustment Severing of fing
Safety Symbols Glossary Power take off (PTO) Fast Slow Engage Decreasing/Increasing Disengage On/Run Off/stop Engine start Traction drive Forward Reverse Engine stop Neutral Choke First gear Brake system Second gear Parking brake Third gear Battery Fourth gear Fuel 7
Gasoline and Oil Recommended Gasoline Stabilizer/Conditioner Use UNLEADED Regular Gasoline suitable for automotive use (85 pump octane minimum). Leaded regular gasoline may be used if unleaded regular is not available. Add the correct amount of gas stabilizer/conditioner to the gas. Using a stabilizer/conditioner that is isopropyl-based in the machine: IMPORTANT: Never use methanol, gasoline containing methanol, or gasohol containing more than 10% ethanol because the fuel system could be damaged.
Set-up Loose Parts Note: Use the chart below to verify all parts have been shipped. DESCRIPTION QTY. USE Upper Handle 1 Flanged bolt 3/8–16 x 1” (26 mm) 4 Flange nut 3/8–16 4 Shift lever 1 Shift lever mounting bracket 1 Washer 1/4” 1 Bolt 1/4–28 x 2” (51 mm) 1 Rod fitting 2 Clevis pin 2 Washer 2 Hairpin cotter 2 Fuel tank 1 Control panel 1 Bolt 5/16–1/ x 7/8” (22.
Set-Up Mount Control Panel and Fuel Tank 1. Install Shift Lever 1. Position control panel under bottom of rear frame (Fig. 1). Align fuel tank to top of rear frame (Fig. 1). Align mounting block with flats of shaft on top of transmission and slide onto shaft (Fig. 3). Note: 2. 3 DO NOT remove rubber washer on transmission shaft. Slide shift lever through control panel and align mounting hole in lever with mounting block on transmission. Secure lever to transmission with 51 mm bolt and washer.
Set-Up Install Upper Handle Connect Throttle Cable 1. 1. Place throttle control lever in FAST position.(Fig. 5). 2. Hook wire Z–bend into hole of speed control lever (Fig. 5). 3. Loosen cable clamp screw allowing cable installation, but do not tighten (Fig. 5). Route cables and wire harness inside of frame (Fig. 4) 4. Move control cable casing and wire until hole in speed control lever is aligned with hole in base plate. Insert a 1/4 in. (6.
Set-Up Connect Wire Harness Install Control Rods 1. 1. Thread a rod fitting onto each control rod approximately 2 in. (51 mm) (Fig. 7) or until upper control bar (Fig. 8). is approximately perpendicular to the ground. 2. Mount rod fitting ends to mounting holes in idler brackets (from outside) with clevis pins, washers and hairpin cotters (Fig. 7). Secure clutch and engine in–line wire connectors (Fig. 6). 2153 Figure 6 1. Clutch wire connector 2. 3. 12 2.
Set-Up 3. Check gap between upper control bar and upper handle when fully engaging wheel belts. Gap should be approximately 1 to 1-1/4 in. (25–32 mm) (Fig. 8). Note: 6. If an adjustment to brake rods is required, remove hairpin cotter and washer securing brake rod fitting to idler bracket (Fig. 9). 7. Adjust wing nut up or down on brake rod and resecure to idler bracket (Fig. 9). Check adjustment and readjust if necessary.
Operation Think Safety First Please carefully read all the safety instructions and symbols in the safety section. Knowing this information could help you, your family, pets or bystanders avoid injury. Controls Become familiar with all the controls (Fig. 10) before you start the engine and operate the machine. Recoil Starter – Pull recoil Starter handle to start engine. Fuel Shut–off Valve – (Under fuel tank) Close fuel shut–off valve when transporting or storing mower.
Operation Parking Brake Always set the parking brake when you stop the machine or leave it unattended. Setting the Parking Brake 1. Pull the upper control bar (Fig. 11) rearward and hold it in this position. 2. Lift the parking brake lock (Fig. 11) up and gradually release the upper control bar. The brake lock should stay in the set (locked) position. Releasing the Parking Brake 1. Pull rearward on the upper control bar (Fig. 11). Lower the parking brake lock to the released position. 2.
Operation Starting and Stopping the Engine 2 Starting 1. Make sure spark plug wire(s) are installed on spark plug(s) and fuel valve is open. 2. Move the shift lever to neutral, set the parking brake and turn ignition key to RUN. 3. Move the throttle control to CHOKE position before starting a cold engine. Note: 4. A warm or hot engine usually does not require any choking. To start a warm engine, move throttle control to FAST position.
Operation Operating Mower Blade Control (PTO) The Safety Interlock System The blade control switch (PTO) in conjunction with the blade control bail engages and disengages power to the electric clutch and mower blades. Engaging the Mower Blades (PTO) 1. Pull on the upper control bar to stop the machine (Fig. 13). 2. To engage blade, squeeze blade control bail against upper control bar 3. Press rocker switch forward “ON” and release. Hold blade control bail against control bar while operating. 4.
Operation Driving Forward or Backward The throttle control regulates the engine speed as measured in rpm (revolutions per minute). Place the throttle control in the “FAST” position for best performance. Forward 1. To go forward, move the shift lever to a forward gear. 2. Release the parking brake: refer to Releasing the Parking Brake, page 15. 3. Slowly press on the upper control bar to move forward (Fig. 14). To go straight, apply equal pressure to both ends of the upper control bar (Fig. 14).
Maintenance Service Interval Chart Service Operation Oil—check level Each Use 8 Hours 25 Hours 50 Hours 100 Hours 250 Hours X Oil—change* X Initial Safety System—check X Brake—check X Wheel Bearings—grease* X X X X X X X Transmission Couplings—grease* X Foam Air Cleaner—service* X X Belts—check for wear/cracks X X X X X Electric Clutch–Adjust X X Gasoline—drain Engine—clean outside X X X Fuel Filter—replace Tires—check pressure X X Paper Air Cleaner—replace* Spark Plug(
Maintenance Cleaning the Foam and Paper Elements Air Cleaner 1. Service Interval/Specification Foam Element Foam Element: Clean and re-oil after every 25 operating hours. A. Wash the foam element in liquid soap and warm water. When the element is clean, rinse it thoroughly. Paper Element: Replace after every 100 operating hours. B. Dry the element by squeezing it in a clean cloth. C. Put one or two ounces of oil on the element (Fig. 16). Squeeze the element to distribute the oil.
Maintenance 2. Paper Element Engine Oil A. Lightly tap the element on a flat surface to remove dust and dirt (Fig. 17). Service Interval/Specification B. Change oil: Inspect the element for tears, an oily film, and damage to the rubber seal. IMPORTANT: Never clean the paper element with pressurized air or liquids, such as solvent, gas, or kerosene. Replace the paper element if it is damaged, defective, or cannot be cleaned thoroughly. • After the first 8 operating hours.
Maintenance Checking Oil Level Changing/Draining Oil 1. 1. Start the engine and let it run five minutes. This warms the oil so it drains better. 2. Park the machine so that the drain side is slightly lower than the opposite side to assure the oil drains completely. Then disengage the power take off (PTO), set the parking brake, and turn the ignition key to “OFF” to stop the engine. Remove the key. 3. Place a pan below the oil drain. Remove the oil drain plug (Fig. 19). 4.
Maintenance Checking the Spark Plug Spark Plug 1. Service Interval/Specification Look at the center of the spark plug(s) (Fig. 21). If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty. Check the spark plug(s) after every 200 operating hours. Make sure the air gap between the center and side electrodes is correct before installing the spark plug.
Maintenance Greasing and Lubrication 2. Service Interval/Specification Lubricate the transmission couplers (Fig. 23). Guard does not have to be removed if you go in from the front, next to engine. Grease the wheel bearings every 8 operating hours and the transmission couplers every 250 operating hours. Grease more frequently when operating conditions are extremely dusty or sandy. Grease Type: General-purpose grease. How to Grease 1.
Maintenance Brake Always set the parking brake when you stop the machine or leave it unattended. If the parking brake does not hold securely, an adjustment is required. Adjusting the Brake The brake lever is on the upper control bar (Fig. 10). If the parking brake does not hold securely, an adjustment is required. 1. Check the brake before you adjust it; refer to Checking the Brake, page 25. 2. Release the parking brake; refer to Releasing the Parking Brake, page 15. 3. Remove the belt cover (Fig.
Maintenance Fuel Tank Draining The Fuel Tank 1 POTENTIAL HAZARD • In certain conditions gasoline is extremely flammable and highly explosive. WHAT CAN HAPPEN • A fire or explosion from gasoline can burn you, others, and cause property damage. HOW TO AVOID THE HAZARD • Drain gasoline from the fuel tank when the engine is cold. Do this outdoors in an open area. Wipe up any gasoline that spills. • Never drain gasoline near an open flame or where gasoline fumes may be ignited by a spark.
Maintenance Fuel Filter Replacing the Drive Belt Service Interval/Specification 1. Remove belt guard, not shown for clarity. Replace the fuel filter after every 100 operating hours or yearly, whichever occurs first. 2. Remove top capscrew securing idler support and idler bracket to rear frame (Fig. 28). 3. Loosen bottom two mounting screws enough to allow belt to pass between drive pulley and idler support (Fig. 28). 4. Raise wheel off ground enough to allow belt removal.
Maintenance Replacing the Traction Belt Adjusting the Electric Clutch 1. Raise the front of the machine and hold with jack stands. Remove lower shield (4) bolts. The clutch is adjustable to ensure proper engagement and proper braking. Check adjustment after every 100 hours of operation. 2. Disconnect in–line wire connector from wire harness to electric clutch. 3. Remove left front engine mounting bolt securing clutch retainer to frame (Fig. 29). Unhook retainer from clutch and remove retainer. 4.
Maintenance Wiring Diagram $ 1 $-, ! /", ! ," " * * & $ # $- * & -+ %( $ $-, ! '"$ '!%+ "&"%-% & % &, )-"* % &,+ .
Maintenance Cleaning and Storage 1. 2. Disengage the power take off (PTO), set the parking brake, and turn the ignition key to “OFF” to stop the engine. Remove the key. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine. Clean dirt and chaff from the outside of the engine’s cylinder head fins and blower housing. IMPORTANT: You can wash the machine with mild detergent and water. Do not pressure wash the machine.
Troubleshooting PROBLEM Engine g will not start,, starts hard,, or f il to kkeep running. fails i Engine g loses power. Engine g over heats. Abnormal vibration. POSSIBLE CAUSES CORRECTIVE ACTION 1. Fuel tank is empty. 1. Fill fuel tank with gasoline. 2. Choke is not ON. 2. Move choke lever to ON. 3. Air cleaner is dirty. 3. Clean or replace air cleaner element. 4. Spark plug wire is loose or disconnected. 4. Install wire on spark plug. 5.
Troubleshooting PROBLEM Machine does not drive. 32 POSSIBLE CAUSES CORRECTIVE ACTION 1. Shift lever is in NEUTRAL. 1. Move shift lever to a drive gear position. 2. Traction belt is worn, loose or broken. 2. Contact Authorized Service Dealer. 3. Traction belt is off pulley. 3. Contact Authorized Service Dealer.