Installation Instructions

ManualsBrandsToro ManualsLawn MowersToro 20655

Form No. 3356-266 Rev A

Electric Bed Lift Kit

For For Gas-Powered Mid-Duty Workman and Twister

Utility Vehicles

Model No. 07262 —Serial No. 270000001 and Up

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Prepare the Machine

Lift bracket, upper

Flange head screw (5/16 x 3/4 inch)

Lift cylinder support

Lift actuator

U-bolts

Flange nut (3/8 inch)

Carriage bolts (3/8 x 3/4 inch)

Clevis pin, short

Cotter pin

Install the bed lift

Switch

Thermal fuse, 15 amp

Clevis pin, long

Cotter pin

Install the switch

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (8 pages)

PAGE 1
Form No. 3356-266 Rev A Electric Bed Lift Kit For For Gas-Powered Mid-Duty Workman and Twister Utility Vehicles Model No. 07262—Serial No. 270000001 and Up Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Step 1 2 3 Description Qty.
PAGE 2
Step 1 Preparing the Machine No Parts Required Procedure Figure 1 1. Position the machine on a level surface. Set the parking brake, turn the ignition off, and remove the key. 1. Prop rod 4. Disconnect the battery cables from the battery. 5. Remove the bracket securing the battery to the battery base. Lift the battery out of the battery base. If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders.
PAGE 3
Step Remove the 2 ﬂange head screws securing each side of the latch rod bracket to the underside and front face of the box (). Retain all parts for future use. 2 Installing the Bed Lift Parts needed for this step: 1 4 1 1 2 6 2 1 1 Figure 3 1. Latch rod bracket 3. 2. Latch rod 4.
PAGE 4
and 4 ﬂange nuts (3/4 inch) while aligning the mounting holes with the holes in the battery tray (Figure 5). Figure 6 1. Actuator 2. Lift cylinder support Figure 5 1. Lift cylinder support 2. Right end of the axle 4. 5. 3. Rear frame battery tray 6. U-bolt Carriage bolt, 3/8 x 3/4 inch Flange nut, 3/4 inch 4. Secure the lift cylinder support to the rear frame with 2 carriage bolts (3/8 x 3/4 inch) and 2 ﬂange nuts (3/8 inch).
PAGE 5
Step 5. Install the battery and connect the cables. 3 6. Press the switch upward to extend the actuator rod until it is aligned with the mounting holes in the upper lift bracket. Secure the rod to the bracket with the clevis pin and cotter pin. Installing the Switch 7. Remove the screws and clip securing the prop rod to the frame rail (Figure 8). Parts needed for this step: 1 1 1 1 Switch Thermal fuse, 15 amp Clevis pin, long Cotter pin Procedure 1.
PAGE 6
Operation Important: When a ratcheting noise is heard, the box lift is completely extended or retracted. Do not continue pressing the switch. Raising the Bed Driving the vehicle with the cargo box raised may cause the vehicle to tip or roll easier. The box structure may become damaged if the box is raised for an extended period of time while operating the vehicle. • Only operate the vehicle when the cargo box is down. • After a load has been dumped, lower the cargo box. 1.
PAGE 7
PAGE 8