Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 112-8349

Form No. 3357-923 Rev A

Tilt Switch Kit

For Z Master Mowers

Model No. 112–8349

Installation Instructions

Due to c hanging regulations reg arding the sale

of items containing mercur y , T oro will no long er

sell the tilt switc h. T he switc h should be remo v ed

from the product and retur ned for disposal in the

enclosed shipping container .

T he mercur y contained in the tilt s witch

is poisonous and exposur e to mercur y can

cause sev er e illness.

• Nev er attempt to open or r epair the tilt

s witch.

• A v oid contact with the mercur y .

Step

Removing the Tilt Switch

No Parts Required

Procedure

Note: T here are no par ts supplied with this

kit to re place the tilt switc h. T he follo wing

instr uctions explain the remo v al of the switc h and

the reconnecting of the existing wire har ness’.

1. Diseng ag e the PTO , mo v e the motion control

lev ers to the neutral loc k ed position and set

the parking brak e .

2. Stop the engine , remo v e the k ey , and w ait for

all mo ving par ts to stop before lea ving the

operating position.

3. Tilt the seat forw ard.

4. F or Z100 and Z400 Z Masters , disconnect the

tilt switc h wire har ness from the seat switc h

( Figure 1 ).

5. R emo v e the bolts holding the tilt switc h to the

frame and disconnect the main wire har ness

from the switc h.

6. Connect the main wire har ness directly to the

seat switc h.

Figure 1

Z100 and Z400 Z Masters

1. Tilt switch 3. Main wire harness

2. Seat switch

7. F or Z200 and Z500 Z Masters , disconnect the

tilt switc h wire har ness from the seat switc h

wire har ness ( Figure 2 ).

8. R emo v e the bolts holding the tilt switc h to the

frame and disconnect the main wire har ness

from the switc h.

9. Connect the main wire har ness directly to the

seat switc h wire har ness .

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (4 pages)

PAGE 1
Form No. 3357-923 Rev A Tilt Switch Kit For Z Master Mowers Model No. 112–8349 Installation Instructions Due to changing regulations regarding the sale of items containing mercury, Toro will no longer sell the tilt switch. The switch should be removed from the product and returned for disposal in the enclosed shipping container. 6. Connect the main wire harness directly to the seat switch. The mercury contained in the tilt switch is poisonous and exposure to mercury can cause severe illness.
PAGE 2
Step 2 Recycling the Tilt Switch No Parts Required Procedure The tilt switch on your unit contains mercury, a hazardous material. Mercury that is outside a sealed container vaporizes at room temperature. The vapors are harmful. Mercury can be absorbed through the skin. Do not attempt to open or repair this switch. A very small amount of mercury is contained in a hermetically sealed body. The steel switch is then potted in a hard epoxy in a plastic case.
PAGE 3
Form No. 3357-923 Rev A Kit de interruptor de inclinación Cortacéspedes Z Master Nº de modelo 112–8349 Instrucciones de Instalación Debido a cambios en la normativa sobre la venta de artículos que contienen mercurio, Toro dejará de vender el interruptor de inclinación. El interruptor debe ser retirado del producto y devuelto en el embalaje adjunto para su eliminación. 5. Retire los pernos que sujetan el interruptor de inclinación al bastidor y desconecte el arnés de cables principal del interruptor. 6.
PAGE 4
2 8. Retire los pernos que sujetan el interruptor de inclinación al bastidor y desconecte el arnés de cables principal del interruptor. 9. Conecte el arnés de cables principal directamente al arnés de cables del interruptor del asiento. Reciclado del interruptor de inclinación de mercurio No se necesitan piezas Procedimiento El interruptor de inclinación de su unidad contiene mercurio, un material peligroso. El mercurio se vaporiza a temperatura ambiente si no está dentro de un recipiente sellado.