Installation Instructions

ManualsBrandsToro ManualsSprayersTank Agitation Kit, 2005 and 2006 Multi-Pro 1250 Turf Sprayer

FormNo.3358-351RevA

TankAgitationKit

for2005and2006Multi-Pro1250TurfSprayer

ModelNo.112-7942

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Neutralizethetank.

Adapterassembly2

Nipple,short6

Cross

Nipple6

Elbow,90degree6

Agitationnozzle6

Nut6

Preparethenewtankagitationnozzles.

Nopartsrequired

–

Removethetankagitationnozzles.

Nopartsrequired

–

Installthenewtankagitationnozzles.

Agitationreducer1Installthereducer.

Nopartsrequired

–

Finishtheinstallation.

Chemicalsarehazardousandcaninjureyou,

bystanders,animals,plants,soils,orother

property.

•Carefullyreadandfollowthechemical

manufacturer’sinstructionsforthesafe

preparation,use,anddisposalofthe

chemical.

•Keepchemicalsoffofyourorbystander’s

skin.Ifcontactshouldoccur,washitoff

immediatelywithcleanwateranddetergent.

•Weargogglesandotherprotective

equipmentasinstructedbythechemical

manufacturer.

CleaningandNeutralizingthe

Tank

NoPartsRequired

Procedure

1.Movethesprayerontoalevelsurface,settheparking

brake,stopthepump,stoptheengine,andremove

theignitionkey.

2.Drainthecontentsofthetanktoremoveany

solutionintank.RefertotheOperator’sManualfor

moreinformation.

Important:Properlydisposeofunused

chemicalsandchemicalcontainersasinstructed

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3358-351 Rev A Tank Agitation Kit for 2005 and 2006 Multi-Pro 1250 Turf Sprayer Model No. 112-7942 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Neutralize the tank. 2 Adapter assembly Nipple, short Cross Nipple Elbow, 90 degree Agitation nozzle Nut 2 6 2 6 6 6 6 Prepare the new tank agitation nozzles. No parts required – Remove the tank agitation nozzles.
PAGE 2
by the chemical manufacturer and your local codes. 2 3. Perform the procedure for Cleaning the Sprayer described in Operation section in the Operator’s Manual. Use a cleaning/neutralizing agent in the water as needed. G006347 3 4 1 Note: Consult the chemical manufacturers instruction of the last chemical used to select the proper cleaning/neutralizing agent. 5 6 4. Rinse the sprayer a minimum of three times to make sure the tank is clean. On the final rinse, use only clean, clear water.
PAGE 3
Removing the Tank Agitation Nozzles 1 No Parts Required Procedure 3 Chemicals are hazardous and can injure you, bystanders, animals, plants, soils, or other property. 2 • Carefully read and follow the chemical manufacturer’s instructions for the safe preparation, use, and disposal of the chemical. G006349 Figure 3 Top View 1. Rear Nozzle 2. Forward Nozzle 3. 10 degrees • Keep chemicals off of your or bystander’s skin. If contact should occur, wash it off immediately with clean water and detergent.
PAGE 4
Installing the New Tank Agitation Nozzles No Parts Required Procedure 1. Enter tank to install the new tank agitation nozzles. 2. Install the nozzles as shown in Figure 5 and secure nozzles using the retaining forks removed previously. 2 1 3 4 3 4 5 G006351 Figure 5 1. Rear nozzle 2. Forward nozzle 3. Adapter assembly 4. Bulkhead 5. Main tank assembly 3. Exit the tank and replace the strainer. Close the tank cover.
PAGE 5
2 3 Installing the Reducer Parts needed for this procedure: 1 4 Agitation reducer Procedure 1. Locate the agitation control valve on the right side of the main tank. Remove the retaining fork securing the agitation control valve to the upper tee. Retain all parts. 5 1 G006346 Figure 6 1. Control valve 2. Agitation reducer 3. Upper tee Chemicals are hazardous and can injure you, bystanders, animals, plants, soils, or other property.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8