Operator's Manual
Table Of Contents
- NO TITLE
- .
- 1 Removing the Aerator from the Crating
- 2 Connecting the Lower Link Arms
- 3 Connecting the Hydraulic Top Link
- 4 Installing the Depth Gauge
- 5 Connecting the Traction Unit Upper Link
- 6 Verifying the Hydraulic Top Link Setup
- 7 Checking the PTO Angle
- 8 Fitting the PTO Shaft
- 9 Installing the PTO Shield
- 10 Connecting the PTO Shaft
- 11 Adjusting the Sway Links
- 12 Leveling the Aerator Side-to-Side
- 13 Installing the Tines
- 14 Setting the Tine Depth
- 15 Installing the Rear Guard
- 16 Removing the Storage Stands
- 17 Installing the Latch Lock
- 18 Applying the CE Decal and the Production Year Decal
- NO TITLE
- NO TITLE
- NO TITLE
- During Operation Safety
- Slope Safety
- Aerating Procedures
- Subsoil Cultivation
- Hard Ground
- Longer/Larger Tines
- Multi Row Adapter Heads
- Root Zone Lifting
- Adjusting the Tine Angle (Models SR54, SR54-S, SR70 and SR70-S)
- Adjusting the Tine Angle (Model SR72)
- Adjusting the Tine Depth (Models SR54-S and SR70-S)
- Adjusting the Tine Depth (Models SR54, SR70, and SR72)
- Adjusting the Head Return Springs
- Transport Operation
- NO TITLE
- NO TITLE
- NO TITLE
- .
- Maintenance Safety
- Lifting the Machine
- Greasing the PTO Shaft and Roller Bearings
- Gearbox Oil Specification
- Checking the Gearbox Oil
- Changing the Gearbox Oil
- Inspecting/Adjusting the Drive Chain
- Adjusting the Drive Chain
- Lubricating the Drive Chain
- Adjusting the PTO Clutch
- Fastener Torque Specifications
- Checking the Springs
- Adjusting the Hole Spacing
- Removing the Aerator from the Traction Unit
- Troubleshooting
- NO TITLE
- What is this warning?
- What is Prop 65?
- Does this law apply everywhere?
- How do the California warnings compare to federal limits?
- Why don’t all similar products carry the warning?
- Why does Toro include this warning?
connectthecylindertothetractionunit(Figure
5).
Note:Ifyouinstalltheextensionblockand
needtoretractthecylindertoinstallit,the
aeratortineheadswillgetclosertotheground.
Installtheextensionblocksasfollows:
A.Removethecotterpinandpinsecuring
thestandardconnectinglinktothecylinder
(Figure5).Removetheconnectinglink
fromthecylinder.
B.Installtherequiredlengthextensionblock
tothecylinderwiththepinspreviously
removed(Figure5).
4
InstallingtheDepthGauge
ModelsSR54,SR70,andSR72
Partsneededforthisprocedure:
1Depthgauge
1
Slideblock
2
Machinescrew(#10x1/2inch)
2
Screw(1/4x2-1/2inch)
1Tubeclamp
1Weldplate
1Depthdecal
Procedure
1.Mountthedepthgaugetotheatsideofthe
slideblockwith2machinescrews(#10x1/2
inch),positioningthecomponentsasshownin
Figure8.
g024283
Figure8
1.Screw
5.Depthdecal
2.Depthgauge
6.Cylinder
3.Machinescrew(2)
7.Weldplate
4.Slideblock
8.Tubeclamp
2.Usingthetubeclamp,weldplateand2screws
(1/4x2-1/2inches),looselymountthedepth
gaugetotherodendofthetoplinkcylinder
(Figure8).Makesurethattheclampsareloose
enoughtoallowthemtorotatetothedesired
position.
3.Makesurethatthetopofthecylinderisclean
enoughtoexcepttheinstallationofadecal.
4.Afxthedepthdecaltothetopofthecylinder
atalocationthatisvisiblefromtheoperating
positionanddoesnotinterferewithhydraulic
hosesorotherobstructions(Figure8).Alignthe
endofthedecalwiththeletter“J”towardthe
aerator.
5.Checktomakesurethecylinderrodcanextend
andretractfullywithoutinterferingwithother
tractionunitoraeratorcomponents.Whenthe
depthgaugeinpositionedcorrectly,tighten
mountingscrews.
6.Runtheaeratoronatestplottodeterminethe
desiredsettingandnotethecorresponding
positiononthedepthindicator.
Ifneeded,youcanadjustthecylinderwhile
operationtheaeratortoadeepersetting(toward
“J”)orshallowersetting(toward“A”).
11