Service Manual
Table Of Contents
- Title Page
- Revision History
- Reader Comments
- Preface
- Table Of Contents (Page 1)
- Table of Contents (Page 2)
- 1 - Safety
- 2 - Product Records and Maintenance
- 3 - Kubota EFI Gasoline Engine
- 4 - Kubota Diesel Engine
- 5 - Kohler Air Cooled Gasoline Engine
- 6 - Drive Train
- 7 - Chassis
- Specifications
- General Information
- Special Tools
- Troubleshooting
- Service and Repairs
- Wheel Assembly
- Brake System
- Brake Caliper Service
- Bleed Brake System
- Parking Brake Caliper Service
- Brake Master Cylinder
- Brake Master Cylinder Service
- Parking Brake Cable
- Wheel Hub
- Steering Assembly
- Front Control Arms
- Front Compression Spring Service
- Front Shock Absorber
- Rear Shock Absorber
- Rear Leaf Spring
- Front Wheel Alignment
- Steering Wheel
- Seat Base
- Hood
- Windshield Wiper Assembly (Machines with Operator Cab)1. Flange- head screw (10 each)2. Sealing washer (10 each)3. Cab roof4. Bulb trim seal5. Console foam6. Fuse block mount7. Wiper motor8. Wiper motor bracket9. Roof console10. Clip
- 8 - Electrical System
- Electrical Schematics
- Special Tools
- Troubleshooting
- Electrical System Quick Checks
- Component Testing
- Ignition (Key) Switch
- Gauge Cluster
- Fuses
- Headlight Switch
- Clutch Switch(s)
- Brake Switch(s)
- Hydraulic Lift Lever Interlock Switch
- 3rd - High Lockout Key Switch
- Transaxle Switches
- Power Relay (Four Terminals)
- Relay (Five Terminals)
- Fusible Link
- Diodes
- Electronic Throttle Control (Workman HDX)
- Fuel Run/Stop Solenoid (Workman HDX-D)
- Fuel Gauge Sender (Workman HD & HDX-D)
- Fuel Pump/Sender (Workman HDX)
- Fuel Pump (Workman HDX-D)
- Temperature Sender (Workman HDX and HDX-D)
- Electric Fan Thermal Switch (Workman HDX-D)
- Speed Sensor
- Glow Controller (Workman HDX-D)
- High Flow Hydraulics Kit Switch (High Flow Hydraulics Kit)
- Hydraulic Solenoid Valve Coil (High Flow Hydraulics Kit)
- Rear PTO Switch (Optional Kit)
- Interlock Switch (1/3 Area Lift Platform Kit)
- Windshield Washer/Wiper Switch (Machines with Operator Cab)
- Diode Assembly (Machines with Operator Cab)
- Service and Repairs
- 9 - Hydraulic System
- Specifications
- General Information
- Special Tools
- Hydraulic Schematics
- Hydraulic Circuit Operation
- Troubleshooting
- Testing
- Primary Hydraulic System Gear Pump Flow Test (Workman HDX and HDX-D)
- Primary Hydraulic System Gear Pump Flow Test (Workman HD)
- Primary Hydraulic System Relief Valve Pressure Test
- Steering Control Valve and Steering Cylinder Test
- Lift Cylinder Internal Leakage Test
- High Flow Hydraulic System Gear Pump Flow and Relief Pressure Tests
- Service and Repairs
- General Precautions for Removing and Installing Hydraulic System Components
- Check Hydraulic Lines and Hoses
- Primary Hydraulic System Gear Pump (Workman HDX and HDX-D)
- Primary Hydraulic System Gear Pump (Workman HD)
- Primary Hydraulic System Gear Pump Service
- High Flow Hydraulic System Gear Pump Service
- Lift Valve
- Lift Valve Service
- Steering Control Valve
- Steering Control Valve Service
- Steering Cylinder
- Steering Cylinder Service
- Lift Cylinder
- Lift Cylinder Service
- Hydraulic Manifold (High Flow Hydraulics Kit)
- 10 - Front Wheel Drive (4WD)
- 11 - Electrical Drawings
- Electrical Drawing Designations
- Workman HD (Serial Numbers313000001 to 404350000)
- Workman HD (Serial NumbersAbove 404350001)
- Workman HDX (Serial Numbers313000001 to 401400000)
- Workman HDX (Serial Numbers401400001 to 404350000)
- Workman HDX (Serial NumbersAbove 404350001)
- Workman HDX--D (Serial Numbers313000000 to 314000000)
- Workman HDX--D (Serial Numbers314000001 to 401420000)
- Workman HDX--D (Serial Numbers401420001 to 404350000)
- Workman HDX--D (Serial NumbersAbove 404350001)
- Front Wire Harness: Workman HD (SerialNumbers 313000000 to 314000000)
- Front Wire Harness: Workman HD (SerialNumbers 314000001 to 401406000)
- Front Wire Harness: Workman HD (SerialNumbers 401406001 to 404350000)
- Front Wire Harness: Workman HD (Serial Numbers 404350001 to 409080000)
- Front Wire Harness Drawing(Serial Number above 409080000)
- Rear Wire Harness Drawing Serial Number below 409080000)
- Rear Wire Harness Drawing(Serial Number above 409080000)
- Front Wire Harness: Workman HDX (SerialNumbers 313000001 to 314000000)
- Front Wire Harness: Workman HDX (SerialNumbers 314000001 to 316000000)
- Front Wire Harness: Workman HDX (SerialNumbers 316000001 to 316999999)
- Front Wire Harness: Workman HDX (SerialNumbers 400000000 to 401400000)
- Front Wire Harness: Workman HDX (SerialNumbers 401400001 to 404350000)
- Front Wire Harness: Workman HDX (SerialNumbers 404350001 to 409100000)
- Front Wire Harness Drawing(Serial Number above 409100000)
- Rear Wire Harness: Workman HDX (SerialNumbers 313000001 to 315000500)
- Rear Wire Harness: Workman HDX (SerialNumbers 315000501 to 316999999)
- Rear Wire Harness: Workman HDX (SerialNumbers 400000000 to 401420000)
- Rear Wire Harness: Workman HDX (SerialNumbers 401420001 to 409100000)
- Rear Wire Harness Drawing(Serial Number above 409100000)
- Front Wire Harness: Workman HDX--D (SerialNumber 313000000 to 314000000)
- Front Wire Harness: Workman HDX--D (SerialNumber 314000001 to 316000000)
- Front Wire Harness: Workman HDX--D (SerialNumber 316000001 to 400000000)
- Front Wire Harness: Workman HDX--D (SerialNumber 400000001 to 401420000)
- Front Wire Harness: Workman HDX--D (SerialNumber 401420001 to 404350000)
- Front Wire Harness: Workman HDX--D (SerialNumber 4043500001 to 408000000)
- Workman HDX--D Front Wire Harness Drawing(Serial Number above 408000000)
- Rear Wire Harness: Workman HDX--D (SerialNumbers 313000000 to 400000000)
- Rear Wire Harness: Workman HDX--D (SerialNumbers 400000001 to 401420000)
- Rear Wire Harness: Workman HDX--D (SerialNumbers 401420001 to 408000000)
- Workman HDX--D Rear Wire Harness Drawing(Serial Number above 408000000)
- Front Wire Harness:Workman HDX--D (Industrial)
- Rear Wire Harness:Workman HDX--D (Industrial)
- Heater Kit--Wire Harness DrawingWorkman HD Series
Workman HD Series Page 7 - 23 Chassis
Removal (Fig. 15)
1. Park vehicle on a level surface, shut engine off and
remove key from ignition switch.
2. Jack up and support rear of vehicle (see Jacking Ve-
hicle in Chapter 1 - Safety in this manual). Make sure
that vehicle is supported with jack stands.
3. For wheel hub to be serviced, remove wheel, brake
caliper and brake rotor (see Brake System Disassembly
in this section).
IMPORTANT: Spindle nuts are staked (deformed) to
the splined shaft during assembly. Clear away the
deformed area of the nut before removing the nut
from the shaft or damage to the shaft threads will
occur.
4. If rear wheel hub is to be removed, remove spindle
nut that secures splined shaft to wheel hub.
5. Using wheel hub hole to access flange head screws,
remove screws that secure wheel hub to vehicle. Re-
move wheel hub from vehicle.
6. Inspect wheel studs in hub and replace studs if dam-
age is identified. Use press to extract stud(s) from hub.
NOTE: If wheel hub wear or damage exists, replace-
ment of the wheel hub assembly is necessary. Wheel
hubs are not rebuildable.
7. If front wheel hub replacement is necessary, remove
cap screw, washers and lock nut from wheel hub assem-
bly so that these components can be installed on re-
placement hub.
Installation (Fig. 15)
1. If front wheel hub is being replaced, install cap screw,
washers and lock nut to new hub. Torque lock nut from
170 to 180 ft- lb (231 to 244 N- m).
2. If any wheel studs were removed from hub, press
new stud(s) fully into hub making sure that stud shoulder
is tight against hub.
3. If rear wheel hub was removed, apply antiseize lubri-
cant to splined shaft.
4. Position wheel hub to vehicle and secure with four (4)
flange head screws. Torque screws from 35 to 40 ft- lb
(48to55N-m).
5. If rear wheel hub was removed, secure wheel hub to
splined shaft with spindle nut. Torque spindle nut from
170 to 180 ft- lb (231 to 244 N- m). Then, stake spindle
nut end into slot in splined shaft.
6. Install brake rotor, brake caliper and wheel (see
Brake System Assembly in this section). Make s ure that
wheel lug nuts are properly torqued from 80 to 90 ft- lb
(109 to 122 N- m).
Chassis