Service Manual
Table Of Contents
- Title Page
- Revision History
- Reader Comments
- Preface
- Table Of Contents
- 1 - Safety
- 2 - Product Records and Maintenance
- 3 - Diesel Engine
- KUBOTA WORKSHOP MANUAL, DIESEL ENGINE, SM-E3B SERIES
- 4 - Drive Train
- 5 - Electrical System
- Table of Contents
- General Information
- Special Tools
- Troubleshooting
- Electrical System Quick Checks
- Component Testing
- Ignition Switch
- Indicator Lights
- Fuse Blocks
- Fusible Links
- Hour Meter
- Headlight Switch
- Brake Switch
- Main Power and Glow Relays
- Start Relay
- Glow Plug Controller
- Engine Run Solenoid
- Over Temperature Switch
- Fuel Pump
- Oil Pressure Switch
- Backup Alarm (Optional Kit)
- Backup Switch (Optional Kit)
- Windshield Washer/Wiper Switch (Machines with Operator Cab)
- Diode Assembly (Model 07236)
- Service and Repairs
- 6 - Chassis
- Table of Contents
- Specifications
- General Information
- Special Tools
- Troubleshooting
- Adjustments
- Service and Repairs
- Check Tire Pressure
- Inspect Tires and Wheels
- Upper Steering (Serial Numbers Below: 316000001)
- Steering Gearbox (Serial Numbers Below: 316000001)
- Lower Steering and Front Wheels (Serial Numbers Below: 316000001)
- Steering Assembly (Serial Numbers Above: 316000001)
- Steering Rack Assembly Service (Serial Numbers Above: 316000001)
- Front Shock Absorbers
- A−arms and Front Suspension (Serial Number Below: 316000001)
- A−arms and Front Suspension (Serial Number Above: 316000001)
- Frame Pivot Yoke
- Swing Arm
- Parking Brake
- Rear Wheels and Brakes
- Rear Brake Service
- Front Brake Calipers
- Front Brake Caliper Service
- Brake Master Cylinder
- Brake Master Cylinder Service
- Bleed Brake System
- Seat Base
- Front Hood
- Cargo Box
- Windshield Wiper Assembly (Machines with Operator Cab)
- 7 - Electrical Drawings
- Table of Contents
- Electrical Schematic (Serial Number Below315000000)
- Electrical Schematic (Serial Number315000001 to 403450000)
- Electrical Schematic (Serial NumberAbove 403450001)
- Glow Plug Circuits
- Start Circuits
- Run Circuits
- Main Electrical Harness (Serial NumberBelow 315000000)
- Main Electrical Harness (Serial NumberBelow 315000000)
- Main Electrical Harness (Serial Number315000001 to 403450000)
- Main Electrical Harness (Serial Number315000001 to 403450000)
- Main Electrical Harness (Serial NumberAbove 403450001)
- Main Electrical Harness (Serial NumberAbove 403450001)
- Engine Electrical Harness
- Heater Kit--Wire Harness Drawing
- Cab Headliner--Wire Harness Drawing
![](/manual/toro/07359/service-manual-english/images/img-99.png)
Workman MDX−D Electrical SystemPage 5 − 23
Windshield Washer/Wiper Switch (Machines with Operator Cab)
The windshield washer/wiper switch controls the opera-
tion of the windshield wiper and washer pump. The
switch is located in the roof console (Fig. 32).
Testing
1. Park the machine on a level surface, lower the cut-
ting deck, set the parking brake, and shut off the engine.
2. To access the switch, do as follows:
A. Remove the 10 clips, 10 sealing washers, and 10
flange−head screws that secure the roof to the cab
frame, and remove the roof.
B. Remove the console foam.
C. Remove the console panel from the roof console.
3. Disconnect the wire harness electrical connector
from the windshield wiper/washer switch.
4. With the use of a multimeter (ohms setting), test the
switch functions to determine if continuity exists be-
tween the various terminals for each switch position.
Check the continuity between the switch terminals. The
windshield wiper/washer switch terminals are identified
in Figure 33 and the circuitry of the switch is shown in be-
low table:
SWITCH
POSITION
NORMAL
CIRCUITS
OTHER
CIRCUITS
OFF 2 + 1 None
WIPER ON 2 + 3 None
WASHER ON 2 + 3 5 + 6
5. Replace the windshield wiper/washer switch if test-
ing determines that the switch is damaged.
6. If the windshield wiper/washer switch testing is cor-
rect and a circuit problem still exists, check the wire har-
ness; refer to the Chapter 7 − Electrical Drawings.
1. Washer/wiper switch 2. Console panel
Figure 32
1
2
Figure 33
7. After you complete the testing, connect the wire har-
ness connector to the windshield wiper/washer switch.
8. Position the console foam. Secure the roof to the cab
frame with the 10 clips, 10 sealing washers, and 10
flange−head screws.