Operator's Manual
Safe operation begins before taking the vehicle out for
a day's work. You should check these items each time:
Check tire pressure.
.2% These tires are different than car tires, they
require less pressure to minimize turf compaction and
damage.
Check all fluid levels and add the appropriate
amount of Toro specified fluids, if any are found to be
low.
Check brake pedal operation.
Check to see that the lights and horn are working.
Turn steering wheel to the left and right to check
steering response.
Check for oil leaks, loose parts and any other
noticeable malfunctions. Make sure engine is off and
all moving parts have stopped before checking for oil
leaks, loose parts and other malfunctions.
If any of the above items are not correct, notify your
mechanic or check with your supervisor before taking
the vehicle out for the day. Your supervisor may want
you to check other items on a daily basis, so ask what
your responsibilities are.
Sit on operator's seat and engage parking brake.
Disengage PTO (if so equipped) and return hand
throttle lever to OFF position (if so equipped).
Move shift lever to NEUTRAL position and depress
clutch pedal.
Keep foot off accelerator pedal.
In extremely cold weather (below 0_ F) -
fully depress and release the accelerator pedal
several times before trying to start engine.
,If engine is hot
- depress and hold the
accelerator pedal about half way down while
cranking engine.
If engine is flooded
- fully depress
accelerator pedal and hold it to the floor until the
engine starts. Never pump the accelerator pedal.
Insert key into ignition switch and rotate it
clockwise to start the engine. Release key when
engine starts.
. /0%4%-2 .4%0(%!2)-' .& 2(% 12!02%0
,.2.0 $. -.2 %-'!'% 12!02%0 +.-'%0 2(!-
1%#.-$1 &2%0 1%#.-$1 .& #.-2)-3.31 #0!-*)-'
5!)2 1%#.-$1 "%&.0% %-'!')-' 12!02%0 ,.2.0
!'!)-
Release parking brake.
Fully depress clutch pedal.
Move gear shift lever to 1st gear.
Release clutch pedal smoothly while depressing
accelerator pedal.
When vehicle gains enough speed, remove foot
from accelerator pedal, fully depress clutch pedal,
move gear shift lever to next gear and release clutch
pedal while depressing accelerator pedal. Repeat
procedure until desired speed is attained. Stop vehicle
before shifting to reverse and forward.
.2% Avoid long periods of engine idling.
.2% Leaving ignition switch in ON" position for long
periods of time without running engine will discharge
battery.
. -.2 (.+$ &0.-2 5(%%+1 230-%$
!'!)-12 2(% 0)'(2 .0 +%&2 12./1 &.0 +.-'%0 2(!-
1%#.-$1 (% (6$0!3+)# /3,/ ,!6 .4%0 (%!2
0%13+2)-' )- /3,/ .0 12%%0)-' '%!0 $!,!'%
Do not attempt to push or tow vehicle to get it
started. Damage to drive train could result.
To stop machine, remove foot from accelerator
pedal, depress clutch pedal, then depress brake
pedal.
To stop engine, rotate ignition key to OFF and
engage parking brake. Remove key from switch to
prevent accidental starting.
Your Workman is ready for work. To provide proper
performance and long vehicle life, follow these
guidelines for the first 100 operating hours.
D Check the fluid and engine oil levels regularly and
be alert for indications of overheating in any
component of the vehicle.
D After starting a cold engine, let it warm up for about
15 seconds before shifting into gear.
D Avoid racing the engine.
D Avoid situations requiring hard stops, especially
when hauling heavy loads or pulling a trailer. It is
necessary to fully break-in a new set of brake linings
to achieve full braking performance. Follow this
guideline whenever new linings are installed.
D Vary vehicle speeds during operation. Avoid
excessive idling. Avoid fast starts and quick stops.
D A break-in oil for engine is not required. Original
engine oil is the same type specified for regular oil
changes.
D Refer to Maintenance section of Operator's Manual
for any special low hour checks.