Service Manual
Table Of Contents
- Title Page
- Revision History
- Reader Comments
- Preface
- Table Of Contents
- 1 : Safety
- 2 : Product Records and Maintenance
- 3 : Engine
- SUBARU SERVICE MANUAL
- 4 : Traction and Reel Drive System
- Table of Contents
- Specifications
- General Information
- Special Tools
- Adjustments
- Service and Repairs
- Reel Drive Belt
- Reel Drive Assembly
- Reel Drive Bearing Housing
- Drum Drive Belt
- Drum Drive Idler Assembly
- Traction Drums
- Differential Assembly
- Differential Assembly Service
- Transmission Drive Belt
- Transmission Idler System
- Transmission Reel Drive System
- Removing Seized Reel Clutch Shaft From Transmission
- Transmission Clutch System (1800/2100)
- Clutch Assembly Service (1800/2100)
- Transmission Clutch System (1820/2120)
- Clutch Assembly Service (1820/2120)
- Clutch Shaft Service (1820/2120)
- Transmission Drum Drive System
- Transmission
- 5 : Electrical System
- 6 : Chassis and Controls
- 7 : Cutting Unit
- 8 : Belt Driven Groomer (Optional)
- Table of Contents
- Specifications
- General Information
- Troubleshooting
- Adjustments
- Service and Repairs
- Groomer Belt Replacement (Forward Rotating Groomer Drive)
- Groomer Cover (Counter Rotating Groomer Drive)
- Grooming Reel (Forward Rotating Groomer Drive)
- Grooming Reel (Counter Rotating Groomer Drive)
- Grooming Reel Service
- Grooming Reel Bearing Replacement
- Idler Assembly (Forward Rotating Groomer Drive)
- Idler Assembly (Counter Rotating Groomer Drive)
- Lift Arm Assembly
- Groomer Brush
- 9: Universal Groomer (Optional)
Greensmaster Flex 1800/1820/2100/2120Belt Driven Groomer (Optional) Page 8 − 10
Grooming Reel (Forward Rotating Groomer Drive)
Figure 7
1. Lock nut (4 used)
2. Drive cover
3. Groomer drive belt
4. Drive pulley
5. Shoulder bolt (2 used)
6. Spring
7. RH drive plate assembly
8. Groomer shim
9. RH groomer arm assembly
10. Cap screw (2 used)
11. Bushing (2 used)
12. Spring washer (2 used)
13. Lock nut (2 used)
14. LH support plate assembly
15. LH groomer arm assembly
16. HOC washer (2 used)
17. Rear roller height shim
18. Socket head screw (4 used)
19. Driven pulley
20. HOC screw (2 used)
21. HOC nut (2 used)
22. Plow bolt (2 used)
23. Grooming reel assembly
24. Front roller assembly
25. RH cutting unit sideplate
26. LH cutting unit sideplate
27. O−ring
FRONT
RIGHT
Antiseize
Lubricant
100 ft−lb
(135 N−m)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1
20
21
22
23
24
11
12
13
25
26
27
17 to 21 ft−lb
(24 to 28 N−m)
Remove the grooming reel to replace individual blades,
to replace worn groomer components, to reverse the
blades on the shaft (if not equipped with carbide blades)
or to replace the grooming shaft.
Removal (Fig. 7)
1. Position machine on a clean and level surface with
engine stopped. Engage parking brake.
2. Remove the cutting unit from the machine and place
cutting unit on a flat work area.
3. Remove groomer drive cover (item 2) and groomer
drive belt (item 3) from groomer drive (see Groomer Belt
Replacement in this section).
4. Loosen cap screws (item 10) that secure front roller
shaft to groomer arms.
5. Remove lock nut and spring washer that secure RH
groomer arm lift rod to RH drive plate assembly (Fig. 8).