Service Manual
Table Of Contents
- Title Page
- Revision History
- Reader Comments
- Preface
- Table Of Contents
- 1 - Safety
- 2 - Product Records and Maintenance
- 3 - Kubota Diesel Engine
- 4 - Hydraulic System
- Specifications
- General Information
- Special Tools
- Hydraulic Schematics
- Hydraulic Flow Diagrams
- Troubleshooting
- Testing
- Traction Circuit Testing - Charge Pressure Test
- Traction Unit Testing - Wheel Motor Efficiency Tests
- Traction Circuit Testing - Piston Pump/Hydrostat Flow and Relief Pressure Test
- Cutting Unit Circuit Testing - Pressure Test
- Cutting Unit Circuit Testing - Reel Motor Efficiency/Case Drain Test
- Cutting Unit Circuit Testing - Reel Motor Cross-Over Relief Pressure Test (Reelmaster 3575-D)
- Cutting Unit Circuit Testing - Proportional Relief Valve (PRV) Pressure Test
- Cutting Unit Circuit Testing - Mow Control Manifold Relief Valve (RV) Pressure Test
- Cutting Unit Circuit Testing - Gear Pump (P1) Flow Test
- Steering/Lift Circuit Testing - Gear Pump (P2) Flow Test
- Steering/Lift Circuit Testing - Lift Relief Valve (RV1) Pressure Test (Reelmaster 3555-D and 3575-D)
- Steering/Lift Circuit Testing - Steering Relief Valve Pressure Test
- Steering/Lift Circuit Testing - Steering Control Valve and Steering Cylinder Test
- Adjustments
- Service and Repairs
- General Precautions for Removing and Installing Hydraulic System Components
- Check Hydraulic Lines and Hoses
- Priming Hydraulic Pumps
- Flush Hydraulic System
- Filtering Closed-Loop Traction Circuit
- Charge Hydraulic System
- Hydraulic Tank
- Radiator and Oil Cooler Assembly
- Hydraulic Pump Assembly
- Neutral Arm Assembly
- Piston Pump/Hydrostat
- Piston Pump/Hydrostat Service
- Gear Pump
- Gear Pump Service
- Front Wheel Motors
- Rear Wheel Motor
- Wheel Motor Service
- Cutting Unit Reel Motor
- Cutting Unit Reel Motor Service (Reelmaster 3550-D and 3555-D)
- Cutting Unit Reel Motor Service (Reelmaster 3575-D)
- Mow Control Manifold
- Mow Control Manifold Service
- Lift Control Manifold
- Lift Control Manifold Service (Reelmaster 3550-D)
- Lift Control Manifold Service (Reelmaster 3555-D and 3575-D)
- Control Manifold Cartridge Valve Service
- Steering Control Valve
- Steering Control Valve Service
- Steering Cylinder
- Steering Cylinder Service
- Front Lift Cylinders
- Rear Lift Cylinders
- Lift Cylinder Service
- 5 - Electrical System
- General Information
- Electrical Schematic
- Special Tools
- Troubleshooting
- Electrical System Quick Checks
- Adjustments
- Component Testing
- Ignition Switch
- Main Power Relay
- Fuses
- Fusible Links
- Toro Electronic Controller (TEC)
- Parking Brake Switch
- Neutral Switch
- Lower/Raise Joystick Switches
- Reel Enable/Disable Switch
- Mow/Transport Switch
- Seat Switch
- Backlap Switch
- Turn Around Switch (Reelmaster 3555-D and 3575-D)
- Engine Temperature Sender
- Start Relay
- Fuel Stop Solenoid
- Fuel Pump
- Glow Relay
- Hydraulic Solenoid Valve Coils
- Indicator Lights
- CAN-bus Termination Resistors
- Hour Meter
- Oil Pressure Switch
- Worklight Switch
- Service and Repairs
- 6 - Chassis
- 7 - DPA Cutting Units
- 8 - Belt Driven Groomer (Optional)
- 9 - Universal Groomer (Optional)
- 10 - Foldout Drawings
- Electrical Drawing Designations
- Reelmaster 3550-D Hydraulic Schematic
- Reelmaster 3555-D/3575-D Hydraulic Schematic
- Reelmaster 3550-D Electrical Schematic (machine serial numbers below 316000300)
- Reelmaster 3550-D (machine serial numbers above 316000300) Electrical Schematic
- Reelmaster 3555-D/3575-D Electrical Schematic
- Reelmaster 3550--D/3555--D/3575--D Electrical Schematic (Serial Numbers Above 403446001)
- Reelmaster 3550-D (machine serial numbers below 316000300) Wire Harness Drawing
- Reelmaster 3550-D (machine serial numbers below 316000300) Wire Harness Diagram
- Reelmaster 3550--D/3555--D/3575--D (Machine serial number 316000301 to 403446000) Wire Harness Drawing
- Reelmaster 3550-D (machine serial numbers above 316000300) Wire Harness Diagram
- Reelmaster 3550--D/3555--D/3575--D Wire Harness Drawing(Machine serial number 316000301 to 403446000)
- Reelmaster 3550--D/3555--D/3575--D Wire Harness Drawing Serial Numbers 403446001 to 405999999)
- Reelmaster 3550--D/3555--D/3575--D Wire Harness Drawing (Serial Numbers Above 406000000)
Reelmaster 3550−D/3555−D/3575−D Page 6 − 23 Chassis
Removal (Fig. 15)
1. Park machine on a level surface, lower cutting units,
stop engine, engage parking brake, and remove key
from the ignition switch.
2. Remove cutting units (see Chapter 7 − Cutting Units
in this manual).
3. Remove lynch pin and thrust washer securing pivot
yoke to lift arm and remove pivot yoke.
4. Remove retaining ring and flat washer from one end
of the cylinder pin that secures rod end of lift cylinder to
lift arm. Pull pin from lift arm and cylinder rod. Support
lift cylinder away from lift arm. DO NOT allow the lift cyl-
inder to hang by the hydraulic hoses.
5. Note the position of the spring actuator prior to re-
moval for proper assembly. Insert a tube or similar object
onto the straight end of the counterbalance spring. Lift
the spring end up and remove the spring actuator (cap
screw, spacer, washer, and lock nut) (Fig. 16). Relieve
all tension from the counterbalance spring.
6. Remove flange head screw from lift arm pin.
7. Support lift arm assembly and slide lift arm pin from
frame. Remove lift arm assembly and counterbalance
spring.
8. Repair lift arm as necessary.
1. Counterbalance spring 2. Spring actuator
Figure 16
1 2
Installation (Fig. 15)
1. Position counterbalance spring over lift arm as
shown.
2. Support lift arm and slide lift arm pin into frame. Se-
cure lift arm pin to frame with flange head screw.
3. Insert a tube or similar object onto the straight end of
the counterbalance spring. Lift the spring end up and in-
stall the spring actuator (cap screw, spacer, washer, and
lock nut) (Fig. 16). Rest end of counterbalance spring on
spring actuator.
4. Slide pivot yoke into lift arm and secure with thrust
washer and lynch pin.
5. Secure hydraulic cylinder to the lift arm with pins,
washers, and retaining rings.
6. Install cutting unit to the rear lift arm pivot yoke (see
Chapter 7 − Cutting Units in this manual).
7. Grease rear lift arm and pivot yoke.
Chassis