240-2003 8 IN. DRILL PRESS Operator’s Manual SAVE THIS MANUAL You will need this manual for safety instructions, operating procedures and warranty. Put it and the original sales receipt in a safe dry place for future reference. For questions about this product, please call 1-866-915-8626.
IMPORTANT SAFETY INSTRUCTION WARNING: When using electric tools, machines or equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury. READ ALL INSTRUCTIONS BEFORE USING THIS TOOL 1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don’t use power tools in damp, wet, or poorly lit locations. Don’t expose your tool to rain. Keep the work area well lit.
IMPORTANT SAFETY INSTRUCTION 14. DRESS PROPERLY. Don’t wear loose clothing or jewelry; they can be caught in moving parts. Protective, non-electrically conductive gloves and non-skid footwear are recommended when working. Wear protective hair covering to contain long hair and keep it from harm. 15. USE EYE PROTECTION. Use a full-face mask if the work you’re doing produces Goggles are acceptable in other situations.
SAFETY PRECAUTIONS FOR DRILL PRESS 6. Never perform layout, assembly, or set-up work on the table while the drill is in use. 7. Make sure drill bit is securely locked in the chuck. 8. Make sure chuck key is removed from the chuck before turning power on. 9. Adjust the table or depth stop to avoid drilling into the table. 10. Always stop the drill before removing scrap pieces from the table. 11. Use clamps or a vise to secure workpiece to the table.
SPECIFICATIONS Voltage: 120V ~ 60Hz, Current Rating: 3.0 Amps Spindle Speed: 740, 1100, 1530, 2100, 3140 RPM (No Load) Chuck Capacity: 1/2" Spindle travel: 2" Spindle Attachment: JT33 Table Height Adjustment: 8-1/2" Swing: 8" Contents:(1) Chuck Key (2) 1/8" & 5/32" hex wrench, Product Manual FUNCTION DESCRIPTION 1 10 2 8 3 9 7 4 5 6 1. Belt cover 2. On/Off Switch 3. Chuck 4. Work table 5. Base 6. Lock handle 7. Column assembly 8. Motor 9. Handle 10.
ASSEMBLY AND ADJUSTMENTS WARNING: To reduce the risk of injury, never connect plug to power source outlet until all assembly steps are completed. Base to column (See Fig. 1) 1. Place Colum n (1) on the Base (3) and align holes in the Column with holes in the Base. 2. Attach using Bolt, Spring Washer, and Washer (2) in each hole through the Column and into the Base. 1 2 3 Fig. 1 Fig 1 Table to column (See Fig. 2) 1. Loosen the Lock handle (3) on the table. (2). 2. Slide the Table(2) over the Column (1).
ASSEMBLY AND ADJUSTMENTS Install the chuck (see Fig. 4 ). Fig. 4 1. Inspect and clean the taper hole in the chuck and the spindle. Remove all grease, coatings, and particles from the chuck and spindle surfaces with a clean cloth. 2. Open the chuck jaws by turning the chuck barrel clockwise by hand. Make sure the jaws are completely recessed inside the chuck. 3. Seat the chuck on the spindle by placing a block of wood under the chuck and tapping the wood with a hammer or tap the chuck with a rubber mallet.
ASSEMBLY AND ADJUSTMENTS WARNING: Disconnect the drill press from the power source before making any speed adjustments. ! Adjust speeds and tension the belt 1. 2. 3. 4. Open the drill press pulley cover. Loosen the belt tension knob (2) (see Fig 7). Pull the motor (3) (see Fig. 7) toward the drill press head. Set the belt on the desired steps of the motor and spindle pulleys according to the belt positions on the spindle speed chart . (See above chart) 5.
ASSEMBLY AND ADJUSTMENTS Coil spring adjustment (See Fig. 11) WARNING: Disconnect the drill press from the power source before adjustment . ! 1 7 6 4 8 3 5 2 Fig. 11 If the quill (8) returns too quickly or too slowly when the handles are released, adjust the spring. Note: This adjustment is set at the factory and should not need changing. Re-adjustments may eventually be necessary due to normal wear and tear. 1. Raise the spindle to the top position. 2.
ASSEMBLY AND ADJUSTMENTS 11. If the quill (8) returns gently to top position (correct operation): Tighten the inner nut (4). Do not overtighten. Replace the jam nut (3). Tighten against the inner nut. Remove the screwdriver. Rotate the handles and check the quill (8) for unrestricted movement. 12. If the quill (8) movement is too restricted or tight: Loosen the jam nut (3). Slightly loosen the housing inner nut (4). Tighten the jam nut (3).
OPERATION 4. Select your drilling depth and secure the depth stop lock knob in position. 5. Adjust the table to your desired position. 6. Slowly rotate the wheel handles to bring the drill bit down towards the table and into your workpiece. After drilling a hole, release the wheel handles slowly to return the chuck to its original position. 7. Continue the operation until the task is completed. When completed, switch the drill press off by pressing the “OFF button on the switch.
PARTS LIST AND SCHEMATIC DRAWING 11 12 '(6&5,37,21 12 '(6&5,37,21 1 BASE 38 RULER HOLDER 2 COLUMN FLANGE 39 MAIN SPINDLE 3 FLAT WASHER 40 CHUCK 4 SPRING WASHER 41 HEXAGON BAR WRENCH 5 OUTSIDE HEX. BOLT 42 HEXAGON BAR WRENCH 6 OUTSIDE HEX. BOLT 43 HEX.
PARTS LIST AND SCHEMATIC DRAWING ! WARNING: Repairs should be made by an authorized repair center. Do not open or disassemble this power tool.Contact at 1-866-915-8626 for questions regarding this power tool.
TOOL SHOP® 8 IN. DRILL PRESS 1-YEAR LIMITED WARRANTY: This TOOL SHOP® brand power tool carries a 1-Year Limited Warranty to the original purchaser. If the tool fails within one (1) year from the date of purchase, simply bring this tool with your original sales receipt back to your nearest MENARDS® retail store.
