CONTENTS Foreword.................................................................................................................................................................... 3 Safety Precautions ..................................................................................................................................................... 4 Signal Words Used in this Manual.....................................................................................................................
Emergency Shutdown Procedure ..................................................................................................................... 45 Machine Stability ............................................................................................................................................. 46 Operating on Slopes.........................................................................................................................................
Foreword SAVE THESE INSTRUCTIONS—This manual contains important instructions for Tomahawk Rollers. These instructions have been written expressly by Tomahawk Power and must be followed during installation, operation, and maintenance of the machines. Machine Documentation From this point forward in this documentation Tomahawk Power LLC will be referred to as Tomahawk. Keep a copy of the Owner’s Manual with the machine at all times.
Safety Precautions Signal Words Used in this Manual This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE signal words which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It is used to alert you to potential personal hazards. Obey all safety messages that follow this symbol. DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
engine powers the hydraulic systems that provide machine movement and drum vibration. The vibrating drums smooth and compact the work surface as the machine moves. Machine speed, direction, and vibration are controlled by the operator from the operator’s seat on the platform. The machine is designed as a lightweight roller to be used in the compaction of sub layers and finish layers of asphalt on roads, driveways, parking lots, and other types of asphaltcovered surfaces.
the machine. Familiarize yourself with the location and proper use of all controls and safety devices. Contact your local Tomahawk distributor for additional training if necessary. When operating this machine: Do not allow improperly trained people to operate the machine. People operating the machine must be familiar with the potential risks and hazards associated with it. Operator qualifications Only trained personnel are permitted to start, operate, and shut down the machine.
Safe operating practices When operating this machine do: Remain aware of the machine’s moving parts. Keep hands, feet, and loose clothing away from the machine’s moving parts Always remain seated and wear the seat belt at all times while operating the machine. Keep clear of the articulated steering joint between the front and rear frames. Always disengage and stow the locking bar for the articulated steering joint before operating the machine.
operated. Ensure that the machine will not tip over, roll, slide, or fall when not being operated. Store the machine properly when it is not being used. The machine should be stored in a clean, dry location out of the reach of children. Operating the Machine in Electrical Storms WARNING Operating this machine in an electrical storm can be hazardous. You can be injured or killed by lightning. Be aware of deteriorating weather conditions and approaching electrical storms.
All adjustments and repairs must be completed before operating the machine. Do not operate the machine with a known problem or deficiency. All repairs and adjustments shall be completed by a qualified technician. Turn off the machine before performing maintenance or making repairs. Remain aware of the machine’s moving parts. Keep hands, feet, and loose clothing away from the machine’s moving parts. Re-install the safety devices and guards after repair and maintenance procedures are complete.
Operator Safety while Using Internal Combustion Engines WARNING Internal combustion engines present special hazards during operation and fueling. Failure to follow the warnings and safety standards could result in severe injury or death. Read and follow the warning instructions in the engine owner’s manual and the safety guidelines below. DANGER Exhaust gas from the engine contains carbon monoxide, a deadly poison. Exposure to carbon monoxide can kill you in minutes.
Hydraulic Fluid Safety WARNING Possibility of severe injury. Hydraulic fluid is under high pressure and becomes very hot during operation. To avoid injury, obey the safety instructions listed below. Safety instructions Inspect the hydraulic system thoroughly before operating the machine. Do not touch hydraulic fluid or hydraulic components while the machine is operating. Wait until the machine is cool.
Labels DANGER EXPLOSION HAZARD Never operate the machine in an explosive atmosphere, near combustible materials, or where ventilation does not clear exhaust fumes. CAUTION READ OWNER’S MANUAL Read and understand owner’s manual before using this machine. Failure to follow operating instructions could result in serious injury or death. DANGER ASPHYXIATION HAZARD ■ Engines emit carbon monoxide.
Always stop the engine and let it cool for a few minute before refueling. ATTENTION LIFTING SPOT Lift the machine at the spot indicated. Tie-down Point CAUTION No lift point WARNING WEAR HEARING-PROTECTOR The operator must wear ear protection device during the operation WARNING Always wear seat belt when operating roller. Read the Owner’s Manual for machine information. Engine will stop without operator seated. WARNING Avoid crushing area Articulated steering joint locking location.
WARNING Avoid crushing area. WARNING Disconnect battery before servicing. Read Repair Manual for instructions. Battery contains caustic acid and potentially explosive hydrogen gas. CAUTION ELECTRIC SHOCK HAZARD at auxiliary battery positive terminal. Never touch this terminal and a metal portion of the machine simultaneously. Grease points Inspect and lubricate every 100 hours of operation. Noise emission to the environment according to the European Community’s Directive.
NOTICE Lifting spot Lock articulated joint. Attach chains to the lifting eyes on machine. Attach chains to hook on lifting equipment. All the labels clearly identified according to ISO 6405-1 NAMEPLATE A nameplate listing the model number, max output, operating mass, Spindle speed max, Serial number is attached to this machine.
Lifting and Transporting Locking and Unlocking the Articulated Joint Description A lockarm located below the articulated joint is provided to fasten the front and rear halves of the roller together. Once secured, the lockarm prevents the two halves from swinging together. WARNING Pinching / crushing hazards. Always install the lockarm before you lift the machine, transport the machine, or perform maintenance near the center of the machine. Locking Move the lockarm (a) to the LOCKED position (1).
Lifting the machine Requirements Lifting equipment (crane or hoist) capable of supporting the machine’s weight. See the Technical Data Chapter for your machine. Lifting devices (hooks, chains, and shackles) capable of supporting the machine’s weight. Engine stopped. All access covers closed and secured. WARNING Crushing hazard. You may be crushed if the lifting devices fail. Never stand under, or get onto, the machine while it is being lifted or moved. WARNING Crushing hazard.
WARNING Crushing hazard. An unstable machine may cause the lifting device to fail. You may be crushed if the lifting device fails. Check for machine stability before continuing. 7.Check for stability. If necessary, lower the machine, reposition the lifting devices, and lift the machine a small distance again. 8.Continue lifting the machine only when it is stable.
Tying Down and Transporting the Machine Requirements Engine shut down Parking brake ON Procedure Perform the procedure below to tie down the machine. 1. Make sure that the transport vehicle is capable of handling the weight and size of the machine. See Technical Data for dimensions and operating weight. 2. Lock the articulated steering joint (a). 3. Block or chock the drums as shown. 4. Attach steel ropes or chains to each of the two tie down bars (b) on the front and ear of the machine. 5.
Towing the machine Requirements Second machine of greater size and rigid towing equipment, or Two machines of equal size to towed machine if non-rigid towing equipment is being used Shielding for all machines being used Note: The strength of the towing line or the tow bar should be at least 150 percent of the gross weight of the towing machine.
Manually Releasing the Parking Brake There are two drive motors on the roller—one on each drum. Each drive motor includes a parking brake that is spring activated and hydraulically released (SAHR). NOTICE: To avoid damaging the internal mechanism, do not use power tools to release or reactivate the brakes. Note: This procedure must be performed on both drums. To manually release the brakes: 1. Chock each drum to prevent the machine from moving. 2. Lock the articulated steering joint.
Towing Bypass Valve The drive circuit is equipped with a towing valve (43) to allow oil to bypass the drive motors and let the roller freewheel for towing. The towing valve should be used in emergency cases where the machine has become bogged down in loose or muddy soil, or cannot be driven due to an engine or hydraulic system failure. WARNING With the towing valve open, the drive circuit has no braking action and the machine will roll freely.
Controls Features and Controls Ref. Description Ref.
19 Grease fittings—articulated joint (4places) 42 Parking brake 20 Hydraulic tank fill port 43 Tow valve 21 Hydraulic manifold block 44 Choke lever 22 Water tank fill cap 45 Auxiliary battery positive terminal 23 Lockarm 24
Control Panel and Indicator Lights Ref. 47 Item Hour meter 50 Vibration on indicator 53 Lights switch (if equipped) 54 Throttle switch 56 Low fuel indicator 61 Water spray switch 62 Water spary dial 63 Emergency stop switch Function This instrument meters machine usage. This indicator light illuminates to indicate that the vibration is on. This switch controls power to the lights. This switch sets the position of the throttle, either high or low.
Operation Preparing the Machine for First Use 1. Make sure all loose packaging materials have been removed from the machine. 2. Check the machine and its components for damage. If there is visible damage, do not operate the machine! Contact your Tomahawk dealer immediately for assistance. 3. Take inventory of all items included with the machine and verify that all loose components and fasteners are accounted for. 4. Attach component parts not already attached. 5.
A fire extinguisher is not supplied with this machine. However, a fire extinguisher must be mounted on the machine and made available for use according to local and national regulations. Type Select a fire extinguisher classified for use on engine-powered construction equipment. Installation Install the fire extinguisher according to the manufacturer’s instructions. The installation must be performed by an authorized Tomahawk dealer or service center.
Roll Over Protection Structure (ROPS) Background The machine is equipped with a Roll Over Protection Structure (ROPS). The ROPS is designed to protect the operator in a rollover accident. Depending on the machine model, the ROPS is either fixed (stationary) or foldable. A foldable ROPS is equipped with two sets of hinge pins, or locking pins. This enables the ROPS to be folded either forward or backward as required for transportation or storage. WARNING Crushing hazard.
Raising the ROPS Follow the procedure below to raise the ROPS. WARNING Pinching / crushing hazard. Keep fingers and extremities away from the pivot points when raising or lowering a foldable ROPS. 1. Support the upper half of the ROPS (3) using a crane and suitable rigging capable of supporting 19 kg. WARNING Crushing hazard. Do not remove all cotter pins and locking pins from each side of the ROPS at the same time.
3. Gently lower the upper half of the ROPS. NOTICE: When lowering the ROPS, do not drop the upper frame. Sudden impacts can weaken or damage the ROPS. 4. Insert the locking pins and secure them with the washers (5) and cotter pins. Rotating Beacon (if equipped) The rotating beacon (a) powers up when the ignition switch is turned to the ON position. The beacon illuminates and rotates when powered up. To install the beacon: 1. Slide the rotating beacon onto the light staff. 2.
Operator Presence System The machine is equipped with an “operator presence system”. This system is part of the seat and senses the weight of an operator in the seat. During operation, if the operator leaves the seat, the engine will shut down When the operator sits down again, the forward/reverse control must be placed in the neutral position before the roller can be moved or the vibration can be started. The engine will need to be restarted to continue operation.
Recommended Fuel Use of oxygenated fuels The engine requires regular grade unleaded gasoline. Use only fresh, clean gasoline. Gasoline containing water or dirt will damage the fuel system. Consult the engine owner’s manual for complete fuel specifications. Some conventional gasoline is blended with alcohol. These gasoline is collectively referred to as oxygenated fuels. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement.
Refueling the Machine Requirements Machine shut down Engine cool Machine/fuel tank level with the ground Fresh, clean fuel supply Procedure Perform the procedure below to refuel the machine. WARNING Fire hazard. Fuel and its vapors are extremely flammable. Burning fuel can cause severe burns. Keep all sources of ignition away from the machine while refueling. Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.
Positioning the Scrapers Requirements Machine shut down Parking brake engaged Positions Each drum has two scrapers (a, b). Scrapers prevent dirt and asphalt from sticking to and accumulating on the drum surface. They are spring loaded, and may be set in the travel position (1) or the scraping position (2) by moving the bar up or down.
Using the Seat Belt Precaution Always use the seat belt when operating the machine. To use To use the seat belt: 1. Pull seat belt (c) out of the retractor in a continuous motion. 2. Fasten seat belt catch (b) into buckle (a). 3. Position the seat belt low across the lap of the operator. The retractor will adjust the belt length and the retractor will lock in place. 4. Push the release button (d) on the buckle in order to release the seat belt. The seat belt will automatically retract into the retractor.
Using the Forward / Reverse Lever Background Both roller drums are driven. An infinitely variable displacement pump drives the hydraulic motors fitted to each drum. The machine moves forward or reverse by using the forward/reverse lever located to the side of the operator’s seat. Travel direction Move the forward/reverse lever into FORWARD (f) or REVERSE (r) according to the direction of travel desired. To change direction of travel from FORWARD to REVERSE or vice versa: 1.
Using the Vibration System Background The machine has an exciter on front drum. The exciter is driven by gear-type hydraulic motors. The exciter motor is fed by a fixed-displacement, gear-type hydraulic pump. Starting and stopping vibration To start vibration, press button (a). When vibration is active, the vibration ON indicator on control panel will illuminate. Vibration can be activated while operating in either or forward or reverse, and will remain active until button (a) is pressed again.
Using the Water Spray System Water spray controls Water from the tank is fed to the spray nozzles by an electric pump. A water spray switch (c) controls the water pump motor. A water spray dial (d) controls the water flow. To operate the water spray controls: Water spray switch position 1: activates the water spray Water spray switch position 2: stops the water spray Water spray dial: Rotate the dial clockwise to increase spray frequency. Rotate the dial counter-clockwise to decrease spray frequency.
Using the Manual Parking Brake Background To hold the machine in a stopped position (parked), there is a mechanical parking brake on the rear drive motor. The engine will automatically shut off when the operator leaves the seat, but the parking brake must be set manually. Engaging and releasing To set the parking brake pull the brake lever (a) up until the brake pad engages the rear drum. Always set the parking brake before leaving the machine. To release the parking brake, lower the brake lever.
Parking Brake Adjustment The parking brake is located on the rear drive motor drum support, and is used to prevent the roller from moving when the engine is turned off. Adjust brake for proper holding force as follows: 1. Unscrew brake lever knob (42) until brake can be applied with moderate force. 2. Start roller on level ground and try to travel forward and reverse with brake applied. If roller drives through brake, stop machine, tighten lever knob one turn and repeat process. 3.
Avoiding the Danger Zone Description A “danger zone” is an area near a machine where a person can be seriously injured if struck by, or caught between, moving parts of the machine. On this machine, the danger zone specifically refers to the area near the articulated joint between the front and rear frames (a). The danger zone is identified with safety labels (b) on both sides of the front frame. Avoiding injury Obey the instructions below to avoid injury within the danger zone.
Preliminary Checks Requirements Machine on a flat, level surface Before starting Before starting the machine, check the following items: Engine coolant level Engine oil level Hydraulic oil level Fuel level Condition of oil cooler and radiator cooling fins Water level in tank NOTICE: Top off the lubricating and hydraulic oil levels using products with the grades and specifications shown in the “Lubricants” table found in the Technical Data chapter of this Operator’s Manual.
Starting, Operating, and Stopping the Machine Requirements Machine is in serviceable condition and has been properly maintained There is fuel in the tank DANGER Asphyxiation hazard. Exhaust gases contain carbon monoxide and can kill you in minutes. Do not start the engine in an enclosed space. Starting the machine Perform the steps below to start the machine. 1. Sit in the operator’s seat and fasten the seat belt. 2. Set the parking brake. 3.
Operating the machine Perform the procedure below to operate the roller 1. Before moving the machine, release the parking brake by lowering the brake lever. 2. Set the engine throttle to the high position. This ensures maximum travel speeds and will produce the best compaction results NOTICE: Operating the machine at slower engine speeds will reduce compaction, slow down machine functions, and damage hydraulic components. WARNING High noise levels. Prolonged exposure can damage your hearing.
Emergency Shutdown Procedure If a breakdown/accident occurs while the machine is operating, follow the procedure below. 1. Press the emergency stop switch on panel. Activate the emergency stop switch by pushing the button. Pushing the emergency stop switch: turns off (opens) the main circuit breaker cuts power to the fuel solenoid stops the engine The emergency stop switch will remain activated until the switch is pulled out.
Machine Stability WARNING Crushing hazards. Certain job site conditions or operating practices may adversely affect machine stability. Follow the instructions below to reduce the risk of tipping or falling incidents. Surface conditions Pay attention to changing surface conditions while operating the machine. Adjust speed and travel direction as necessary to maintain safe operation.
Vibrating on a compacted surface Activating the vibration system on a fully compacted surface may cause the drums to rebound and momentarily lose contact with the ground. If this occurs while the machine is on an incline, the machine may slide. If the drums rebound on the compacted surface, reduce vibration speed or stop vibration entirely.
Operating on Slopes Background When operating on slopes or hills, special care must be taken to reduce the risk of personal injury or damage to the machine. Procedure Always operate the machine up and down slopes rather than from side to side. For safe operation and for protection of the engine, continuous duty use should be restricted to slopes of 15° (25% grade) or less. WARNING Crushing hazard. Never operate the machine sideways on slopes. The machine may tip or roll over even on stable ground.
Anti-Vandalism Protection and Machine Access Parts of the machine which may be subject to theft or vandalism when the vehicle is parked unattended can be padlocked to prevent unauthorized access or use. Lockable parts are: Engine cover. a.To lock the engine cover, close the cover. b. Attach a padlock to the fastener. Control panel. a.To lock the control panel, place the anti-vandalism cover over the controls. b. Attach a padlock to the fastener. Fuel cap. a.To lock the fuel cap, close cap completely.
Maintenance WARNING A poorly maintained machine can malfunction, causing injuries or permanent damage to the machine. Keep the machine in safe operating condition by performing periodic maintenance and making repairs as needed. Periodic Maintenance Schedule The table below lists basic machine and engine maintenance. Tasks designated with check marks may be performed by the operator. Tasks designated with square bullet points require special training and equipment.
Rear Frame Access Overview The operator’s platform is hinged and can be tilted to provide access to the water pump, the water filter, the battery, the hydraulic hoses, and the fuel tank. The platform has lifting cylinders and a prop rod that hold the platform in the open position. WARNING Pinching/crushing hazard. The lifting cylinders do not have enough force to lift and hold the platform in the open position when the tank is filled with water. Drain the water tank before tilting the platform.
3. Pull the steering column handle down to lower the platform. 4. Replace the two bolts locking the platform to each side of the rear frame. Maintaining the Seat and Seat Belt Background In order for the seat and seat belt to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. Poorly maintained equipment can become a safety hazard! Maintaining the seat and seat belt Keep the seat clean.
Checking the Water Filter When Check the water filter daily before operating the machine. Daily checks are especially important if the available water supply is cloudy or dirty. Location The water filter is located on the right side of the machine beneath the operator’s platform. The operator’s platform must be lifted to access the water filter. Requirements Engine stopped Water tank drained Operator’s platform lifted (see Rear Frame Access). WARNING Pinching/crushing hazard.
Cleaning the Water Filter When Clean the water filter every 100 hours, or more often if the available water supply is cloudy or dirty. Location The water filter is located on the right side of the machine beneath the operator’s platform. The operator’s platform must be lifted to access the water filter. Requirements Engine stopped Water tank drained Operator’s platform lifted (see Rear Frame Access). WARNING Pinching/crushing hazard.
Grease Fittings See section Technical Data for oil quantity and type. Articulation Joint Lockarm The articulated joint is equipped with grease fittings (a) for lubrication. WARNING Pinching hazard. To avoid being pinched by the machine halves, set the lockarm before greasing the articulating joint! Rear Drum The rear drum drive bearing is equipped with a grease fitting (b) located at the center of the drum behind the right rear drum support. Exciter The exciter is grease lubricated.
Battery WARNING Explosion hazard. Batteries can emit explosive hydrogen gas. Keep all sparks and flames away from the battery. Do not short-circuit battery posts. WARNING Battery fluid is poisonous and corrosive. In the event of ingestion or contact with skin or eyes, seek medical attention immediately. The battery on this machine is equipped with a terminal that allows temporary disconnection of the battery for maintenance work.
Hydraulic System Cleanliness Keeping the hydraulic oil clean is a vital factor affecting the service life of hydraulic components. Oil in hydraulic systems is used not only to transfer power, but also to lubricate the hydraulic components used in the system. Keeping the hydraulic system clean will help avoid costly downtime and repairs.
Checking and Cleaning the Hydraulic Tank Breather Prerequisites Machine shut down Clean, nonflammable solvent When Every 1000 hours of service or yearly Procedure Follow the procedure below to clean the hydraulic tank breather (a). 1. Open the engine compartment. 2. Remove the breather from the hydraulic tank. 3. Clean the breather with clean, nonflammable solvent. 4. Dry the breather with compressed air. 5. Re-install the breather.
6. Bleed the hydraulic system. See section Bleeding the Hydraulic System. Bleeding the Hydraulic System Overview Bleeding trapped air from the hydraulic system is necessary each time the drive system or hydraulic system is opened up. Trapped air bubbles can cause equipment malfunctions or erratic performance. Procedure Follow the procedure below to bleed trapped air from the exciter circuit and the drive circuit. 1.
Checking the Neutral Switch Requirement Parking brake engaged When Every 10 hours of service or daily Procedure Follow the procedure below to check the neutral switch. WARNING Crush hazard. The machine may lurch forward if the neutral switch is out of adjustment while making this test. Be sure the area is clear of all personnel and equipment before making this test. 1. Turn off the engine. 2. Engage the parking brake. 3. Move the forward/reverse lever to the FORWARD position. 4.
Inspecting the Seat Belt Requirements Machine shut down Parking brake engaged When Daily, before starting the machine. Procedure Perform the procedure below to inspect the seat belt. 1. Check the seat belt mounting hardware (a) for wear and damage. Replace damaged hardware. 2. Check the buckle (b) for wear and damage. Replace the seat belt if the buckle is damaged. 3. Inspect the seat belt (c) for wear and damage. Replace the seat belt if it is damaged.
Cleaning the Spray Bars Background Clogged or dirty spray bars can prevent water from spraying onto the drums. If water spray is noticeably reduced or absent even though there is water in the tank, then clean the spray bars. Procedure Follow the procedure below to clean the spray bars. 1. Locate the plugs (a) at the ends of each spray bar (b). Unscrew and remove the plugs. 2. Flush the inside of the spray bar with clean water. 3.
Testing the Brake System Prerequisites 15° slope When Every 500 hours of service or yearly Precaution Use this test to determine if the parking brake is functioning on the specified slope. This test is not intended to measure the maximum brake holding effort. Procedure Follow the procedure below to test the braking system. 1. Position the machine on a 15° slope as shown. 2.
Long-Term Storage Introduction Extended storage of equipment requires preventive maintenance. Performing these steps helps to preserve machine components and ensures the machine will be ready for future use. While not all of these steps necessarily apply to this machine, the basic procedures remain the same. When Prepare your machine for extended storage if it will not be operated for 30 days or more. Preparing for storage Perform the procedures below to prepare your machine for storage.
NOTICE: Allowing the battery to freeze or completely discharge is likely to cause permanent damage. Periodically charge the battery while the machine is not in use. In cold climates, store and charge the battery indoors or in a warm location. Cover the machine. Tires and other exposed rubber items should be protected from the weather. Either cover them or use a readily available protectant.
Troubleshooting Problem / Symptom Engine does not start Reason Fuel tank is empty Refill fuel tank. Wrong type of fuel Drain tank, change fuel filter, and refill with the proper fuel. Old fuel Drain tank, change fuel filter, and refill with fresh fuel. Fuel system not primed Prime the fuel system. Fuel filter clogged is restricted Replace fuel filter. Check battery connections or replace battery as needed. Plugged air elements Clean air cleaner or replace filter elements.
Problem / Symptom No travel, or travel only in one direction No steering Water leaking from spray nozzles when machine is shut off Reason Remedy Parking brake is on Release parking brake. Sheared pin on forward/ reverse control Replace pin. Loose or broken control cable Tighten or replace. Damaged drive motor Repair or replace. Damaged drive pump Repair or replace. Defective relief valve(s) Repair or replace. Damaged steering cylinder Repair or replace.
Schematics Electrical Schematics 68
Electrical Schematic Components Ref. 1 2 3 4 5 6 7 Description Work light switch (optional) Throttle switch Pump switch Key switch Vibration indicator light (green) Low fuel indicator light (amber) Alternator (30A) Ref.
Hydraulic Schematic 70
Hydraulic Schematic Components Ref. 1 2 3 4 5 6 7 Description Steering cylinder Steering unit Drive motor Bypass lever Charge pump Main pump Exciter pump Ref.
Specification Engine Item no. TRR15 Engine type 4-stroke, 2 cylinder, air cooled Engine make Honda Engine model GX630 Max. rated power @ rated speed 1 kW (hp) 15.1 (20.3) @ 3,600 rpm Displacement cm³ (in³) 688 (42) Spark plug Electrode gap Engine speed - operating Valve clearance (cold) intake: exhaust: (NGK) ZFR5F mm 0.71-0.79 (in.) (0.028-0.031) rpm 3,100 mm (in.) 0.10-0.16 (0.004-0.006) 0.10-0.16 (0.004-0.
Machine Item No. Dry Weight Dimensions (LxWxH) TRR15 kg (lb.) 1200 (2,171) mm (in.) 1824(71.8)x1040(40.9)x2290(90.4) mm (in.) 399 (15.7) Curb Clearance: Right Left 208 (8.2) Water Tank Capacity l (gal.) 100 (26.4) Outside Turning Radius m (ft.) 2.45 (8.0) km/hr. (mph) 0-8.7 (0-5.4) Forward / Reverse Speed Grade ability Vibration Frequency 30% vpm 4,200 Lubrication Item No. Hydraulic System CRR-12 type Premium grade, anti-wear hydraulic fluid 10W30 L (gal.) Exciter 20.8 (5.
Hydraulic Pressures Operating Pressure Relief Pressure System Drive** Steering* —while turning Vibration —single drum bar psi bar psi 55–69 800–1,000 200 2,900 0–41 0–725 45–51 650–725 55–76 800–1,100 200 2,900 * Values for hard-packed surface shown. Values may differ depending on surface. ** Charge pressure: 11.4 – 12.8 bar (165–185 psi).
according to ISO 2631-1. The results are compliant to the limit and action vibration values (hand/arm and whole body) as specified in European directive 2006/42/EC. Proposition 65 WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For More Information Visit https://www.p65warnings.ca.
Where a warrantable condition exists, Tomahawk Power, LLC will repair your small offroad engine/equipment at no cost to you including diagnosis, parts and labor. MANUFACTURER'S WARRANTY COVERAGE: The emissions control system is warranted for two years.
DEFECTS WARRANTY REQUIREMENTS (a)The warranty period begins on the date the small engine/equipment is delivered to an ultimate purchaser. (b)General Emissions Warranty Coverage.
part will be repaired or replaced by Tomahawk Power, LLC according to Subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part. (4)Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge to the owner.
not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part. (11)The manufacturer issuing the warranty shall provide any documents that describe that manufacturer's warranty procedures or policies within five working days of request by the Air Resources Board.
(g) Pressure regulator (if equipped) (h) Mixer assembly and its internal components (if equipped) (2) Air Induction System including: (a)Intake pipe/manifold (b)Air cleaner (3)Ignition System including: (a)Spark plug (b)Ignition coil (4)Catalytic Muffler Assembly including: (a)Muffler gasket (b)Exhaust manifold (c)Catalytic converter (5)Crankcase Breather Assembly including: (a) Breather connection tube.
(b) Hoses, belts, connectors, and assemblies.
(b) Hoses, belts, connectors, and assemblies. (7) Fuel tank evaporative emissions control system including: (a) Fuel Tank The warranty is provided in accordance with the “California AND FEDERAL Emission Control Warranty Statement”. Tomahawk Power, LLC San Diego, CA Sales Support (866) 577-4476 sales@tomahawk-power.com Service and Registration support@tomahawk-power.
www.tomahawk-power.