Operation and Instruction Manual
Read carefully this operation manual before starting the machine and always keep the instruction this way you will secure safe operation, high working output and long durability of the machine. The manufacturer bears no responsibility for damages arising from mis use or not following the operation manual. QUICK START INSTRUCTIONS 1. 2. 3. 4. 5. 6.
TABLE OF CONTENTS 0. QUICK START INSTRUCTIONS 1. SAFETY INFORMATION 1.1 Safety Precau�ons 1.2 Opera�ng Safety 1.3 Operator Safety while using Internal Combus�on Engines 1.4 Label Loca�ons 1.5 Safety and Opera�ng Labels 2. OPERATION 2.1 Opera�ng Principle 2.2 Delivery Checks 2.3 Before Star�ng 2.4 To Start 2.5 To Stop 2.6 Applica�on 2.7 Opera�on 2.8 Max. Admissible Inclina�on 2.9 Main Parts and Accessories 3. MAINTENANCE 3.1 Periodic Maintenance Schedule 3.2 Exciter Oil 3.3 V-Belt and Clutch 3.3.
This manual provides information and procedures to safely operate and maintain this model. For your own safety and protection from injury, carefully read, understand and observe the safety instructions described in this manual. Keep this manual or a copy of it with the machine. If you lose this manual or need an additional copy, please contact Tomahawk Power LLC or visit www.tomahawk-power.com.
1.2 Operating Safety -Beware of uneven or slippery work surfaces, as they may cause injury or death. -Exercise care when working in the vicinity of unprotected holes or excavations. -NEVER allow any person to operate the machine without adequate instruction. -NEVER allow any person to operate the machine without adequate instruction. -ENSURE all operators read, understand and follow the operation instructions. -Serious injury could result from improper or careless use of the machine.
-DO NOT use the machine near flammable material or in explosive environments. -Gasoline is extremely flammable and explosive under certain conditions. -ENSURE that the Gasoline is only stored in an approved storage container. -DO NOT refuel the engine while it is in operation or hot. -DO NOT operate or refuel the engine in a confined area without adequate ventilation. -DO NOT refuel the engine in the vicinity of sparks, a naked flame or smoking.
1.3 Operator Safety while using Internal Combustion Engines -DO NOT smoke when refueling the engine or operating the machine. -DO NOT refuel a hot or running engine. -ALWAYS keep away from all hot or spark-generating objects when refueling the engine. -ALWAYS refill the fuel tank until the machine has cooled, and in a well-ventilated environment. -DO NOT spill fuel when refueling the engine. -ALWAYS take care to use the right type of fuel. -ALWAYS inspect the fuel leakage regularly.
1.4 Label Locations CHECK ENGINE OIL REGULARLY SAE10W-30 87 + OCTANE PETROL GASOLINE Carbon monoxide (CO) can cause brain damage or death. Engine and generator exhaust contains odorless and colorless carbon monoxide gas. Signs of carbon monoxide poisoning include nausea, headache, dizziness, drowsiness, and lack of consciousness. Get fresh air if anyone shows signs of carbon monoxide poisoning. INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR’S MANUAL 1.
WARNING Engine emits carbon monoxide; operate only in wellventilated areas. Read the Operator’s Manual for machine information. No sparks, flames, or burning objects near the machine. Shut off the engine before refu-eling. Use only clean, filtered, unleaded gasoline. NOTICE Follow the Maintenance Schedule included in the Operations Manual to check engine oil regularly.
2. OPERATION 2.1 Operating Principle The following instructions were compiled to provide you information on how to obtain long and trouble-free use of the unit. Periodic maintenance of this unit is essential. Read the manual in its entirety and follow the instructions carefully. Failure to do so may injure yourself or a bystander. 2.2 Delivery Checks Immediately on taking delivery of your new equipment and before putting it into service.
NOTICE: Check the oil level in the engine and exciter. Engine and compactor warranties are VOID if this unit is run without oil. Note: the Honda engine is built with a low oil sensor switch if the oil level is not adequate the engine may not start. Before using each time check the oil level. 2.4 To Start 1. Open the fuel cap by moving the fuel ON/OFF lever fully to the right. 2. If starting the engine from cold, set the choke to ON by moving the choke lever fully to the left.
2.5 To Stop 1. Move the throttle lever to “Idle” position. 2. Turn the Red On/Off switch to “Off” position. 3. Close the fuel valve. 2.6 Applications Trench Compaction Road Maintenance Brick Paving Groundwork Landscaping Asphalt Compaction 2.7 Operation Run the engine at full throttle and allow plate to pull itself along at its normal speed. When operating it may be necessary to assist plate by pushing it forward slightly.
2.9 Main Parts and Accessories D A G B H C I E J F A. Handle F. Belt B. Throttle Lever G. Clutch C. Protective Frame H. Rubber Mat (Optional) D. Water Tank (Optional) I. Base Plate E. Belt Cover J.
3. MAINTENANCE 3.1 Periodic Maintenance Schedule Daily After First 20 Hours Every 50 Hours Every 100 Hours Every 200 Hours Starting Check Loosened of Lost Screws Damaged to Parts Control System Functioning Exciter Oil Check Exciter Oil Replacement V-Belt (Clutch) Check Leakage of Oil Fuel Tightness of Fastening Threads Engine Oil Check and Replenishment Engine Oil Replenishment Air Filter Cleaning These inspection intervals are meant for operation under normal conditions.
3.3 V-Belt and Clutch 3.3.1 Checking the V-Belt After 200 hours of operation, remove the upper belt cover to check the V-belt tension (Figure 2). Tension is best if the belt bends about 0.4 in when depressed firmly with finger between grooves. Loose or worn V-belts reduce power transmission efficiency, causing weak compaction, reducing the life of the belt itself. NEVER attempt to check the V-belt while the engine is running. Severe injury can occur if your hand is caught between the V-belt and the clutch.
3.4 Air Filter 1. The air filter element should be cleaned as a clogged air filter can cause poor engine starting, lack of power, and shortened engine life. 2. To clean or replace the air filter, loosen the wing nut on the air filter housing (Figure 1), remove the cover and take out air filter cartridge. If only cleaning of the air filter is needed, blow through the air filter cartridge from the inside, with a jet of dry compressed air, up and down until all dust is removed. 3.
3.7 Troubleshooting 3.7.1 Machine Troubleshooting SYMPTOM Travel speed too low, and the vibration is weak. POSSIBLE CAUSES SOLUTION Engine speed too slow? Set engine speed to correct RPM. Clutch slips? Check or replace clutch. V-belt slips? Adjust or replace V-belt. Excessive oil in vibration? Malfunction in vibrator housing? Drain excess oil and fill to proper level. Check eccentric, gears, and counter weights. Bearing failure? Replace bearing.
3.7.2 Engine Troubleshooting SYMPTOM POSSIBLE CAUSES Spark plug bridging. Difficult to start, fuel is Carbon deposit on spark plug. available, but no SPARK at spark plug. Short circuit due to deficiency. Improper spark plug gap. ON/OFF switch is shorted. Difficult to start, fuel is Ignition coil defective. available, and SPARK is Improper spark gap, points dirty. present at spark plug. Condenser insulation worn or short circuiting. Spark plug wire broken or short circuiting.
SYMPTOM “Weak in power” compression is proper and does not misfire. Engine overheats. Rotational speed fluctuates. Recoil starter malfunction. SOLUTION POSSIBLE CAUSES Air filter not clean. Clean or replace air filter. Improper level in carburetor. Check float adjustment, rebuild carburetor. Defective spark plug. Clean or replace spark plug. Spark plug heat value improper. Replace with correct type of spark plug. Correct type of fuel. Replace with correct type of fuel. Cooling fins dirty.
Sound Specification (According to 2000/14/EC) Model Guaranteed sound power level TPC90H 108dB(A) Vibration Specification (According to ISO 2631 and EN 1033) : Model TPC90H 5 m/s2 Engine Type Honda GX160 Power kW (HP) 4.0kW (5.5 HP) Operating Weight (lb) Plate Size L x W (in) 187 lbs 22 x 20 in Centrifugal Force kN 18 kN (4050lbf) Vibration Frequency Travel Speed 5,400 vpm (90 Hz) 78ft /min Exciter Lubrication 0.25 L, SG15W-40 motor oil 5.
Impact damage is not covered under warranty. Clutches are not covered under any warranty. Engines warranties are guaranteed by Honda on case by case analysis assuming user error was not a cause for the issue. 6. MAINTENANCE RECORDS PREVENTATIVE MAINTENANCE AND ROUTINE SERVICE PLAN Tomahawk’s TPC90 Forward Plate Compactor has been assembled with care and will provide years of service. Preventative maintenance and routine service are essential to the long life of your plate compactor.
SPARE PARTS MANUAL 23
Part Name: BELT COVER 1 P 4 Machine Type: 73& + 24 3
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER 001 42019A 002 2933008016 003 2125000084 PART NAME BELT COVER BOLT WASHER QUANTITY 1 2 3 25
Part Name: COVER POZ.
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER 001 31590A 003 2933008022 004 2985000008 005 2125000084 PART NAME COVER VD BOLT NUT WASHER QUANTITY 1 4 4 8 27
Part Name: THROTTLE OPTION 32196A 4 10 7 2 9 5 POZ.
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER 001 41786A 002 600041787A 003 41238A 004 6000000239 005 2200000006 006 2798504006 007 2934008075 008 3292900005 009 2799105040 010 600041027A PART NAME BOWDEN WIRE NUT LEVEER SPRING BOLT NUT RING BOLT WASHER QUANTITY 1 1 1 1 1 1 1 1 2 2 29
Part Name: SPRINKL(5 6<67(0 19 6 8 4 1 15 22 25 10 18 14 11 2 26 21 24 12 Machine Type: 73& + 30 17
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER 001 41847A 31837A 002 31908A 31860A 004 600031326A 006 41855A 008 6000000048 010 4014435001 011 4014014024 012 4014085034 014 60107 015 60108 017 2933010035 018 2933008025 019 2933008016 021 2985000010 022 2985000008 024 2125000105 025 2125000084 31818A 026 31810A 31862A PART NAME PLATE TUBE VD15P TUBE VD18P TUBE VD20P, 24P TANK HOLDER PLUG WATER TAP SOCKET PLUG TUBE TUBE BOLT BOLT BOLT NUT NUT WASHER WASHER PLATE VD15P PLATE18P PLATE 20P, 24P QUANTIT
Part Name: DAMP(1ING PLATE 7 2 6 1 9 3 5 8 Machine Type: 73& + 32
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER PART NAME 4013100015 DAMPENING PLATE 001 4013100016 DAMPENING PLATE 4013100017 DAMPENING PLATE 40093A PLATE I 002 42010A PLATE I 41886A PLATE I 40094A PLATE II 003 42011A PLATE II 41887A PLATE II 005 2933010040 BOLT 006 2963006025 BOLT 007 2985000010 NUT 008 2934000006 NUT 009 2125000105 WASHER QUANTITY 1 1 1 1 1 1 1 1 1 2 4 2 4 2 33
Part Name: :+((/ .
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER PART NAME 001 3180180211 WHEEL 002 2985000010 NUT 003 2125000105 WASHER 004 2125000084 WASHER 005 2985000008 NUT BOLT 006 2933008025 BOLT 007 42424B RATCHET 008 4014003034 RING 009 4014103034 RING 010 2200042456 SPRING 012 2912010020 BOLT 013 31366B FRAME 014 31608B FRAME 016 42488A ROLLER 018 2933008050 BOLT QUANTITY 2 2 2 11 6 4 1 1 1 1 2 1 1 1 1 35
Part Name: PLATE WITH VIBRATOR 16 5 3 11 13 20 17 23 4 8 12 21 6 15 Machine Type: 73& + 36 18 7 1 22 10
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER 31573A 31574A 001 31575A 31576A 31387B 31387A 003 31387C 31466A 004 31581B 004 31583B 005 31582A 005 31584A 006 31597A 007 6000040044 008 40032A 010 4232124284 011 3110030207 011 3110030307 012 3800000015 013 2256287720 015 4104205518 016 4928110002 017 4928025526 018 3931021014 020 2933010020 021 2933006020 022 2934000010 023 2125000105 PART NAME PLATE PLATE PLATE PLATE ECCENTRIC ECCENTRIC ECCENTRIC ECCENTRIC COVER I COVER I COVER II COVER II PULLEY R
Part Name: DRIVE 9 15 5 21 10 1 19 6 16 14 17 3 11 Machine Type: 73& + 38 12
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER 001 41890A 003 41824A 005 41061A 006 40172A 009 3120010030 010 6000000118 011 4080000785 012 3120010030D 014 2931008040 015 2798504006 016 2933008025 017 2125000084 019 3200000019 021 6800000001 PART NAME HOLDER HOLDER EXHAUST HONDA WASHER MOTOR CLUTCH V-BELT FEATHER BOLT BOLT BOLT WASHER RING SWITCH QUANTITY 1 2 1 1 1 1 1 1 4 2 1 4 1 1 39
Part Name: %(/7 COVER 1 2 4 Machine Type: 73& + 40 PO 1 4 2
TOMAHAWK POWER MACHINE TYPE: TPC90H CHART: LABEL PART NUMBER 001 600031325A 002 31364A 004 2738008016 PART NAME COVER LOGO BOLT QUANTITY 1 1 2 41
Part Name: HOUR COUNTER 5 1 3 Machine Type: 73& + 42 4
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER 001 41893A 003 6000000296 004 2840003008 005 2934000003 PART NAME HOLDER HOUR COUNTER BOLT NUT QUANTITY 1 1 2 2 43
3art Name: FRAME PRACTIC 10 16 17 1 4 13 6 7 12 15 8 Machine Type: 73& + 44 2
TOMAHAWK POWER MACHINE TYPE: TPC90H LABEL PART NUMBER 001 10098A 002 31604A 004 600041988A 006 4236203470 007 4014014033 008 2200000015 010 2933005030 012 2985000008 013 2985000005 015 2125000084 016 2125000053 017 2902100005 PART NAME FRAME HANDLEBAR HOLDER SILENTBLOCK BUSH BOLT PIN BOLT NUT NUT WASHER WASHER WASHER QUANTITY 1 1 1 2 4 2 2 2 2 2 2 2 45