Owner’s Manual Do not use this equipment before reading this manual! ADVANTAGE 400 Electric Piston Pump Model 0552071 Model 0552054 Model 0552072 Register your product online at: NOTE: This manual contains important warnings and instructions. Please read and retain for reference. www.titantool.com Serial Number* * See page 3 for location __________ 0914 • © Titan Tool Inc. All Rights Reserved. Form No.
Important Safety Information · Read all safety information before operating the equipment. Save these instructions. This symbol indicates a hazardous situation, which, if not not avoided could result in death or serious injury. HAZARD: HAZARDOUS VAPORS Paints, solvents, insecticides, and other materials can be harmful if inhaled or come in contact with the body. Vapors can cause severe nausea, fainting, or poisoning.
Important Safety Information · Read all safety information before operating the equipment. Save these instructions. Grounding Instructions HAZARD: EXPLOSION HAZARD DUE TO INCOMPATIBLE MATERIALS Will cause property damage or severe injury. PREVENTION: • Do not use materials containing bleach or chlorine. • Do not use halogenated hydrocarbon solvents such as bleach, mildewcide, methylene chloride and 1,1,1 trichloroethane. They are not compatible with aluminum.
Table of Contents Setup Perform the following procedure before plugging in the power cord of an electric unit. 1. Ensure that the siphon tube and the return hose are attached and secure. 2. Using a wrench, attach a minimum of 50’ of 1/4” airless spray hose to the outlet fitting on the sprayer. Tighten securely. 3. Attach an airless spray gun to the spray hose. Using two wrenches (one on the gun and one on the hose), tighten securely. Safety Precautions.....................................................
Preparing to Paint Painting Before painting, it is important to make sure that the fluid in the system is compatible with the paint that is going to be used. 1. Place the siphon tube into a container of paint. 2. Place the return hose into a metal waste container. 3. Set the pressure to minimum by turning the pressure control knob fully counterclockwise.
Pressure Relief Procedure 1. 2. 3. 4. 5. 6. 7. 8. Keep the spray gun perpendicular to the surface, otherwise one end of the pattern will be thicker than the other. Be sure to follow the pressure relief procedure when shutting the unit down for any purpose, including servicing or adjusting any part of the spray system, changing or cleaning spray tips, or preparing for cleanup. Lock the gun by turning the gun trigger lock to the locked position.
Cleanup Cleaning the Spray Tip 1. Flush the gun with solvent immediately after the work is completed. 2. Oil the sliding pins to prevent them from seizing up. Do not use gasoline to clean the sprayer. Should the spray tip become clogged, reverse the spray tip with the lever and pull the trigger. Once the obstruction comes out of the spray tip, release the trigger, reverse the spray tip back to the spray pattern setting, and resume spraying.
Replacing the prime/spray Valve Gun Filter Perform the following procedure using PRIME/SPRAY valve replacement kit P/N 0507690. 1. Drive the groove pin out of the valve handle. 2. Remove the valve handle and the cam base. 3. Using a wrench, loosen and remove the valve housing assembly from the pump manifold. 4. Make sure the gasket is in place and thread the new valve housing assembly into the pump manifold. Tighten securely with a wrench. 5. Place the cam base over the valve housing assembly.
Replacing the Gears NOTE: If the motor will not dislodge from the pump housing: • Remove the front cover plate. • Using a rubber mallet, carefully tap on the front of the motor crankshaft that extends through the slider assembly. 12. 13. 1. Perform the Pressure Relief Procedure and unplug the sprayer. 2. Loosen and remove the four motor cover screws. Remove the motor cover. 3. Disconnect the black and red wires coming from the gear box housing. 4. Loosen and remove the four motor mounting screws. 5.
Replacing the Transducer 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Servicing the Fluid Section Loosen and remove the four front cover screws. Remove the front cover. Stop the sprayer at the bottom of its stroke so that the piston is in its lowest position. Perform the Pressure Relief Procedure and unplug the sprayer. Use the following procedures to service the valves and repack the fluid section. Perform the following steps before performing any maintenance on the fluid section. 1.
12. Using a wrench, tighten the retainer nut securely. 13. Slide the top of the piston rod into the T-slot on the slider assembly. 14. Position the pump block underneath the pump housing and push up until it rests against the pump housing. NOTE: The outlet cage always must be used with the crush washer. They are included together in the repacking kit as assembly P/N 704-642. 6. Reassemble the valves by reversing the steps above.
Troubleshooting Problem A. The unit will not run. Cause 1. 2. 3. B. The unit will not prime. Plug the unit in. Reset the breaker. Turn the pressure control knob clockwise to supply power to the unit and increase the pressure setting. 4. 5. Inspect or take to a Titan authorized service center. Allow motor to cool. The PRIME/SPRAY valve is in the SPRAY position. Air leak in the siphon tube/suction set. 1. 3. 4. The pump filter and/or inlet screen is clogged. The siphon tube/suction set is clogged.
Notes © Titan Tool Inc. All rights reserved.
Consignes de sécurite important · Lire toutes ces consignes avant d’utiliser l’appareil. Garder ces consignes. DANGER : ÉMANATIONS DANGEREUSES Certains produits (peintures, solvants, insecticides ou autres) peuvent être nocifs s’ils sont inhalés ou entrent en contact avec l’organisme. Les émanations de ces produits peuvent provoquer de graves nausées, évanouissements ou empoisonnements.
Consignes de sécurite important · Lire toutes ces consignes avant d’utiliser l’appareil. Garder ces consignes. Instructions de mise à la terre DANGER : EXPLOSION CAUSÉE PAR DES PRODUITS INCOMPATIBLES Ce type d’explosion peut entraîner des dommages matériels ou des blessures graves. MESURES PRÉVENTIVES : • Ne pas utiliser de produits contenant du chlore ou du javellisant.
Información de seguridad importante · Lea toda la información de seguridad antes de operar el equipo. Guarde estas instrucciones. PELIGRO: VAPORES PELIGROSOS Las pinturas, solventes, insecticidas y demás materiales pueden ser nocivos si se inhalan o toman contacto con el cuerpo. Los vapores pueden causar náuseas graves, desmayos o envenamiento. Indica una situación peligrosa que, de no evitarse, puede causar la muerte o lesiones graves.
Información de seguridad importante · Lea toda la información de seguridad antes de operar el equipo. Guarde estas instrucciones. Instrucciones para conectar a tierra PELIGRO: POSIBLE EXPLOSIÓN DEBIDO A MATERIALES INCOMPATIBLES Causará daños materiales o lesiones graves. PREVENCIÓN: • No use materiales que contengan blanqueador o cloro. • No use solventes de hidrocarburos halogenados como blanqueador, mohocida, cloruro de metileno y 1,1,1 tricloroetano. No son compatibles con el aluminio.
Parts List Main Assembly 1 2 13 3 14 15 4 16 17 5 18 19 6 14 7 8 9 10 11 12 Item 1 2 3 4 5 6 7 8 9 10 11 12 Part # 0558302 0551440 9800308 ---------0551526 0551553 763-552 710-033 730-334 705-054 0551556 710-046 Description Quantity Motor cover................................................1 Screw.........................................................4 Screw.........................................................4 Motor assembly.........................................
Motor Assembly NOTE: All electrical work should be performed by a Titan authorized service center. 1 2 3 4 5 6 7 Item Part # 1 0551540 2 770-099 3 704-206 Description Quantity Motor assembly (includes items 2–7 and items 25, 29, and 30 in the Gear Box Assembly parts list)...................1 Tie wrap.....................................................1 Capacitor...................................................
Gear Box Assembly 4 5 1 2 6 3 7 8 NOTE: All electrical work should be performed by a Titan authorized service center. 9 10 11 12 17 16 24 13 18 19 20 21 22 14 23 15 16 20 © Titan Tool Inc. All rights reserved.
Item Part # 1 700-139 2 0558301 3 0508208 4 0508572 5 704-174 6 704-176 7 0509219 8 700-771 9 0551522 10 02712 11 9822522 12 806-032 13 800-741 806-213 Description Quantity Screw.........................................................4 Front cover................................................1 Slider assembly.........................................1 Crankshaft/gear assembly.........................1 Thrust washer............................................1 Second stage gear.....................
Fluid Section Assembly (Stand and Low Boy Cart P/N 0552754) (Upright Cart P/N 0552762) Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Install upper packing with raised lip and O-ring facing down.
Low Boy Cart Assembly 9 10 11 12 13 1 2 14 15 16 17 18 3 4 5 19 3 6 7 Item 1 2 3 4 5 6 7 8 9 10 11 8 20 Part # 0551608 704-291 0294534 0270394 9890104 9885546 0295615 9805230 773-918 0551551 0551552 Description Quantity Cart weldment (includes items 6 and 14)..1 Roll pin.......................................................2 Wheel spacer.............................................4 Wheel........................................................2 Cap...................................................
Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship.
