Assembly Instruction Sheet

ManualsBrandsThree Posts ManualsCeiling LightsSpofford 5 - Light Shaded Classic / Traditional Chandelier

1of2

Package Contents

Fixture

Loop

Fixture Body

Spacer

Ring

Socket Collar

Shade

Vintage Bulb

(5)MediumBase60WVintageBulbs(supplied),100WMaximum.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Bottom

Assembly

Hardware Contents

Crossbar

Assembly

Ceiling

Canopy

Fixture Chain

Quick Link

STEP 1 Install Fixture Loop-

A. (Refer to Arms Orientation) Unfold

support arms with sockets of the

Fixture Body (C) and branches of the

Bottom Assembly (D) to proper

locations.

ARMS ORIENTATION

Figure 1

Lock Ball

Bolt

(Step 1 Continued)

B. Remove lock balls from the Fixture Body (C). Place the branches of

the Bottom Assembly (D) over the bolts on the Fixture Body (C) and

secure with lock balls. Hand tighten until snug.

C. Place the Spacer (B) over the nipple on the top center of the Fixture

Body (C) and thread the Fixture Loop (A) onto the nipple. Hand

tighten until snug.

STEP 2 - Install the Crossbar Assembly to Outlet Box and Adjust

the length of the Nipple

A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head

of the Green Ground Screw facing you. Secure it with Outlet Box

Screws (not included), tighten until snug

B. Adjust the hex nut and lock washer underside of the crossbar to the

middle of the nipple.

C. Remove the canopy lock ring from the canopy chain loop. Place the

Ceiling Canopy (DD) over the canopy chain loop against the ceiling

to determine the correct position of the nipple. Thread the canopy

lock ring onto the canopy chain loop. Adjust the nipple to allow the

Ceiling Canopy (DD) to rest against the ceiling when held in place by

the canopy lock ring.

D. Remove the canopy lock ring and the Ceiling Canopy (DD). Tighten

the lock washer and the hex nut against the crossbar to secure in

place.

Outlet Box Screw

(not included)

Hex Nut and

Lock Washer

Outlet Box

Green Ground Screw

Canopy Chain Loop

Canopy Lock Ring

Figure 2

Nipple

STEP 3 - Install the Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (BB) to your desired length by removing

links if needed. Put a cloth over the Fixture Chain (BB) to protect the

finish.

B. Pull the supply wires through the Fixture Chain (BB) alternating

links. After the wires are through the Fixture Chain (BB), pull the

Supply Wires and the Ground Wire through the canopy lock ring and

the Ceiling Canopy (DD) in order.

Assembly Instruction Sheet

Thank you for purchasing this product.

Need assistance with parts or assembly? Call our customer service.

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (5) Medium Base 60W Vintage Bulbs (supplied), 100W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
(Step 3 Continued) STEP 5 - Install Shades, Rings and Bulbs C. Attach one end of the Fixture Chain (BB) to the Fixture Loop (A) with one Quick Link (CC). Lift the fixture and Fixture Chain (BB) up and attach the other end of the Fixture Chain (BB) onto the Supply canopy chain loop with another Wires and Quick Link (CC). The fixture will Ground Wire now hang safely. D. Feed the Supply Wires and BB Ground Wire through the canopy chain loop and nipple into the outlet box.