Assembly Instructions

ManualsBrandsThree Posts ManualsCloset & Bedroom StorageRomsey 48" W Closet Storage Island

Hardware List

Part List

Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/16” Drill Bit, 3/8” Drill Bit

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Storage Island

Cam Lock Screw

33 pcs. (+2 extra)

Cam Lock

33 pcs. (+6 extra)

M4x25

Machine Screw

12 pcs.

Knob

12 pcs.

Adjustable Pin

24 pcs. (+1 extra)

M6x32

Head Cap Bolt

14 pcs. (+1 extra)

M3.5x32

Wood Screw

4 pcs. (+1 extra)

Hex Wrench

1 pc.

Small Hex Wrench

1 pc.

Flat Washer

14 pcs. (+1 extra)

Spring Washer

14 pcs. (+1 extra)

Side Panel

1 pc.

Side Panel

1 pc.

Middle Panel

1 pc.

Back Panel

1 pc.

Back Panel

1 pc.

Cartons are also needed for assembly.

Summary of content (9 pages)

PAGE 1
Storage Island IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List B. Side Panel 1 pc. C. Side Panel 1 pc. D. Middle Panel 1 pc. G. Back Panel 1 pc. H. Back Panel 1 pc. Hardware List Hex Wrench 1 pc. Cam Lock Screw 33 pcs.
PAGE 2
Assembly Instructions 2/8 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the screws until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
PAGE 3
Assembly Instructions 3/8 STEP 2 Attach Back Panels (G) and (H) to Middle Panel (D) with Cam Locks. (See Figure 2) Cam Lock H D G Flat Washer Spring Washer Head Cap Bolt Figure 2 STEP 3 Attach Base (E) to unit with Cam Locks, Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway. (See Figure 3) E Tighten all bolts used in this step. Note: Arrow label indicates front of Bottom (E). Arrow label at front Figure 3 Cam Lock J STEP 4 Attach Plinths (J) to unit with Cam Locks.
PAGE 4
Assembly Instructions 4/8 Cam Lock STEP 5 Attach unit to Side Panel (C) with Cam Locks, Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway. Attach Rails (I) to unit with Wood Screws, into pre-drilled holes. (See Figure 4) I I Head Cap Bolt Spring Washer Flat Washer C Figure 4 Wood Screw Wood Screw B Cam Lock STEP 6 Attach Side Panel (B) to unit with Cam Locks, Wood Screws, Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway.
PAGE 5
Assembly Instructions 5/8 Drawer (K) STEP 7 K4 Attach Drawer Sides (K3) and (K4) to Drawer Back (K2), then flip Locks. (See Figures 5 and 6) K2 K3 Lock STEP 8 Figure 5 Figure 6 Slide Drawer Bottom (K5) into grooves in unit. Attach Drawer Front (K1) to unit, then flip Locks. K1 K5 Machine Screw Knob Lock STEP 9 Attach Knobs with Machine Screws. Part List K1. Drawer Front 2 pcs. K2. Drawer Back 2 pcs. K3. Drawer Side 2 pcs. K4. Drawer Side 2 pcs. K5. Drawer Bottom 2 pcs.
PAGE 6
Assembly Instructions 6/8 Drawer (L) L4 STEP 10 Attach Drawer Sides L3) and (L4) to Drawer Back (L2), then flip Locks. L3 L2 Lock L1 STEP 11 Slide Drawer Bottom (L5) into grooves in unit. Attach Drawer Front (L1) to unit, then flip Locks. L5 Lock Machine Screw Knob STEP 12 Attach Knobs with Machine Screws. Part List L1. Drawer Front 4 pcs. L2. Drawer Back 4 pcs. L3. Drawer Side 4 pcs. L4. Drawer Side 4 pcs. L5. Drawer Bottom 4 pcs.
PAGE 7
Assembly Instructions 7/8 Cam Lock STEP 13 A Attach Top (A) to unit from Step 6 with Cam Locks, Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway. Tighten all bolts used in this step. Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 7) Flat Washer Spring Washer Head Cap Bolt Figure 7 K L K STEP 14 L Slide Drawers (K) and (L) into position. L L STEP 15 Insert Adjustable Pins into side panels at desired level.
PAGE 8
Assembly Instructions 8/8 Per regulatory requirements, a Tip-over Restraint is included. Follow Step 16 to install it. STEP 16 Drill a 3/16” hole 1/2” deep 1” below top of unit in middle of side panel that is against a wall. Anchor in wall Bracket on wall Wall Screw 3/16” hole in side panel of unit Wood Screw 3/8” wall hole Place unit at desired location. Drill a 3/8” hole in wall in-line with pre-drilled hole at top of unit. Tie end Move unit.
PAGE 9
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.